Ulta-Mat Heat and Sound Underlayment Set
p/n: 70-4787-88
This Ulta-Mat Heat and Sound Deadener Underlayment Set includes die cut underlayment pieces for the floor, doors, quarter, and roof panels. Underlayment pieces are made from a flexible and lightweight foil facing foam rubber sound and heat insulation material.
Front Door Weatherstrip
p/n: 70-2556-72
Door edge weatherstrip. This part is the primary door to body weatherstrip.
Peel-N-Stick Trunk Weatherstrip
p/n: 70-0774-WT
This Peel-N-Stick Trunk Weatherstrip is designed from the original part for superior fitment and seal. The seal mounts around the full perimeter of the trunk directly to the body. Easy to install 3M Peel-N-Stick backing provides superior adhesion for reliable performance.
Trunk Weatherstrip
p/n: 70-0774-84
This Trunk Weatherstrip is designed from the original part for superior fitment and seal. The weatherstrip mounts around the full perimeter of the trunk directly to the body.
Splash Apron / A-Arm Dust Shield Fillers
p/n: 70-3483-45
This two (2) piece Splash Apron / A-Arm Dust Shield Filler pair is designed from the original part for superior fitment and seal. Filler pieces are die cut from quality masticated rubber to authentic original dimensions. Left and Right pieces fit over suspension a-arms and inside front inner fenders.
Fuel Tank Mounting Isolator Set
p/n: 70-4628-41
This six (6) piece Fuel Tank Mounting Isolator Set is a reproduction of the original style fuel tank isolator set. Replacing or adding the isolator strips and pads can help eliminate noise or friction between the fuel tank straps and the body.
Stabilizer Bar End Link Set
p/n: 60-0221-33
Twenty-two (22) piece Stabilizer Bar End Link set for both sides of one (1) vehicle, fits front or rear bar. Order two (2) sets for vehicles with front and rear stabilizer bars. Hex head bolt 3/8"-16 NF x 6-15/16" long. Comes with metal sleeve, metal cup washers and rubber grommets.
Brake or Clutch Pedal Pad - Manual
p/n: 60-0709-22
A top-quality rubber Clutch or Brake Pedal Pedal Pad reproduction. One (1) each slip-over type pedal pad installs over the full perimeter of the brake or clutch pedal for a precise, factory fit. For manual transmission model GM vehicles only.
Hood To Cowl Weatherstrip
p/n: 70-2807-43
This Hood To Cowl Weatherstrip is designed from the original part for superior fitment and seal. This seal mounts at the rear of the engine bay directly to the body.
Body Mounting Pad
p/n: 70-2165-48
Pad, body mount, lower bolt retaining. Rubber with metal washer molded in. Used on the bottom of most mounting locations.
Brake Pedal Pad - Automatic
p/n: 60-0710-22
This reproduction Brake Pedal Pad slips over the full perimeter of the brake pedal for a precise, factory fit. A direct fit to replace worn, heavy wear original brake pedal pads. For GM models with an automatic transmission.
Transmission Mount
p/n: 70-2058-25
This Transmission Mount is a new aftermarket replacement mount manufactured to meet or exceed factory specifications.. One (1) required per vehicle.
Multi-Purpose Clips
p/n: 70-4802-45
A ten (10) piece set of Multi-Purpose Clips. Commonly used to retain Hood to Cowl Weatherstrips or Inner Fender Splash Panels.
Masticated Rubber Sheet
p/n: 70-0645-45
This Masticated Rubber Sheet is three-thirty seconds (3/32") inch thick. The rubber sheet contains random milled cotton cord reinforcement for front end splash aprons and other project uses.
Peel-N-Stick Trunk Weatherstrip
p/n: 70-0510-WT
This Peel-N-Stick Trunk Weatherstrip is made from a high-quality EPDM sponge rubber. Available by the foot.
1" Trunk Weatherstrip
p/n: 70-0510-85
This Trunk Weatherstrip was designed from an original part for a specific application but has many uses outside of its original purpose. Available by the foot.
2-1/4" Body Hole Plug
p/n: 35-0863-45
This Body Hole Plug is fully molded and designed from the original part for superior fitment and seal. Designed for the trunk, however the generic shape makes this plug usable for a variety of applications.
Hood Bumper Cap
p/n: 70-1651-42
This Hood Bumper Cap is fully molded and designed from the original part for superior fitment and seal. Slip-over style application.
Door or Tailgate Bumper
p/n: 33-1228-71
This Door Bumper is fully molded and designed from the original part for superior fitment. This rubber bumper attaches to the vehicle body to support / cushion the door closure. Usually requires two (2) bumpers each per vehicle.
Door Bumper
p/n: 33-1227-71
This Door Bumper is fully molded and designed from the original part for superior fitment. The twin retainer style rubber bumper attaches to the vehicle body to support/cushion the door closure. Usually requires two (2) bumpers each per vehicle.
3/16" Trunk Bumper
p/n: 33-0990-87
This Trunk Bumper is a quality reproduction of the original factory part. Self-retaining bumper is manufactured to OEM specifications to install for an authentic fit, finish, and function.
Brake Adjustment Hole Cover Plug
p/n: 70-1092-24
A quality molded rubber Brake Adjustment Hole Cover Plug that inserts into brake adjustment hole in the backing plate. Most models with drum brakes. Length: 1.25 inches. Height: .875 inches.
Lock Cylinder Gasket
p/n: 60-0641-69
This Lock Cylinder Gasket is die cut from one-thirty-second (1/32) inch neoprene.
Hood Weatherstrip Clip
p/n: 70-1255-42
Clip, hood to cowl weatherstrip. Normal usage is fourteen (14) to sixteen (16) per car as needed.