Body Weatherstrip Kit
p/n: 90-1035-90
This nine (9) piece Body Weatherstrip Kit includes the major weatherstrip components and some other essential parts needed for the body of your restoration project.
Front Door Weatherstrips
p/n: 60-0645-72
A Front Door Weatherstrip pair with molded ends. This part is the primary door to body weatherstrip. Includes clips for easy installation. Made of top-quality rubber.
Hardtop Roof Rail Weatherstrips
p/n: 82-0042-68
These Hardtop Roof Rail Weatherstrips fit on the roof of the vehicle and seal the side windows when the window is fully raised.
U Jamb Lock Pillar Fillers
p/n: 70-1625-79
This U Jamb Door Lock Pillar Filler pair seals the bottom of the rear side window. May also be known as a door jamb seal.
Beltline Weatherstrip
p/n: 70-0961-60
This Beltline Weatherstrip is thick pile lined without chrome bead. Available in 4ft pairs.
Beltline Weatherstrip Channel
p/n: 70-0651-58
This Beltline Weatherstrip Channel is a five (5) foot length of rigid channel with a flocked rubber lip and a flat stainless bead. Can be used as the inner beltline weatherstrip on front doors, rear doors and quarter windows.
Side Window Vertical Leading Edge
p/n: 50-0344-80
This Side Window Vertical Leading Edge pair is designed from the original part for superior fitment and seal. This part attaches to the vertical edge of the rear side windows when the rear side windows are fully raised.
Peel-N-Stick Trunk Weatherstrip
p/n: 70-0773-WT
This Steele exclusive Peel-N-Stick Trunk Weatherstrip is designed from the original part for superior fitment and seal. This easy to install weatherstrip mounts around the full perimeter of the trunk directly to the body.
Trunk Weatherstrip
p/n: 70-0773-84
This Trunk Weatherstrip is designed from the original part for superior fitment and seal. The seal mounts around the full perimeter of the trunk directly to the body.
Radiator Mounting Insulator Pads
p/n: 70-2016-31
A Radiator Mounting Insulator Pad pair for use on the corners of the radiator. One (1) pair per side.
Stabilizer Bar End Link Set
p/n: 60-0221-33
Twenty-two (22) piece Stabilizer Bar End Link set for both sides of one (1) vehicle, fits front or rear bar. Order two (2) sets for vehicles with front and rear stabilizer bars. Hex head bolt 3/8"-16 NF x 6-15/16" long. Comes with metal sleeve, metal cup washers and rubber grommets.
Battery Clamp Cover
p/n: 70-0095-21
This Battery Clamp Cover helps to protect the nearby metal and finish. Fully molded from high-quality EPDM rubber to ensure durability. Good copy from an original part.
Rocker Panel Inner Drain Cover
p/n: 70-2392-45
This Rocker Panel Inner Drain Cover pair is designed from the original part for superior fitment and seal. Fully molded with proper attaching teeth and flap.
Stabilizer Bar Bushings
p/n: 70-4678-34
This Stabilizer Bar to Frame Bushing pair may fit either front or rear stabilizer / sway bars depending on the vehicle. Manufactured with quality materials to original specifications.
Body Mounting Pad
p/n: 70-2165-48
Pad, body mount, lower bolt retaining. Rubber with metal washer molded in. Used on the bottom of most mounting locations.
Transmission Mount
p/n: 70-2058-25
This Transmission Mount is a new aftermarket replacement mount manufactured to meet or exceed factory specifications.. One (1) required per vehicle.
Dimmer Switch Grommet
p/n: 40-0083-88
This Dimmer Switch Grommet is used during carpet installations in automotive restorations. Made from high-quality EPDM dense rubber to provide excellent durability. Includes a wide flange for floor dimmer switch fitments.
Hood Bumper
p/n: 50-0205-42
This Hood Bumper is the adjustable type for the front of the hood. Used to support/cushion the hood closure. Cadmium plated bolt (5/16)-18 x 1-1/4". Excellent appearance with authentic details like original.
5/8" Door Weatherstrip with Clips
p/n: 70-1112-73
This Door Weatherstrip with Clips is made made from high quality EPDM sponge rubber. Excellent for use on many different vehicle models. Available by the foot.
13/16" Door Weatherstrip with Clips
p/n: 70-1245-73
This Door Weatherstrip is made from high quality EPDM sponge rubber. Excellent for use on many different vehicle models. Available by the foot.
Masticated Rubber Sheet
p/n: 70-0645-45
This Masticated Rubber Sheet is three-thirty seconds (3/32) inch thick. The rubber sheet contains random milled cotton cord reinforcement for front end splash aprons, etc.
2-5/8" Run Channel Mohair Liner
p/n: 70-2863-58
This Run Channel Mohair Liner helps to reline the guide bars on the lock side of hardtops and convertibles. This mohair liner comes with a rubber backing and installs with adhesive to the division bars and channel. Available by the foot.
1-1/16" Trunk Weatherstrip
p/n: 70-0346-85
This Trunk Weatherstrip is designed from an original part for a specific application but has many uses outside of its original purpose. Available by the foot.
Peel-N-Stick Trunk Weatherstrip
p/n: 70-0510-WT
This Peel-N-Stick Trunk Weatherstrip is made from a high-quality EPDM sponge rubber. Available by the foot.
Hood to Fender Bumper
p/n: 70-1963-42
This Hood to Fender Bumper is a quality reproduction of the original factory part. These rubber bumpers attach to the front fender to support / cushion the hood closure.
1" Trunk Weatherstrip
p/n: 70-0510-85
This Trunk Weatherstrip was designed from an original part for a specific application but has many uses outside of its original purpose. Available by the foot.
Door Bottom Drain Hole Seal
p/n: 70-0938-70
This Door Bottom Drain Hole Seal is designed from the original part for superior fitment and seal. This part fits into the lower door on both two (2) and four (4) door models.
13/16" Door Weatherstrip without Clips
p/n: 70-1244-73
This Door Weatherstrip is made from high-quality EPDM sponge rubber. Excellent for use on many different vehicle models. Available by the foot.
2-1/4" Body Hole Plug
p/n: 35-0863-45
This Body Hole Plug is fully molded and designed from the original part for superior fitment and seal. Designed for the trunk, however the generic shape makes this plug usable for a variety of applications.
5/8" Door Weatherstrip without Clips
p/n: 70-1111-73
This Door Weatherstrip made from high-quality EPDM sponge rubber. Excellent for use on many different vehicle models. Available by the foot.
Door Bumper
p/n: 33-0981-71
This Door Bumper is designed from the original part for superior fitment, finish and function. Molded with push in carrot retainers, this bumper is commonly used as a upper door bumper on GM models.
Door or Tailgate Bumper
p/n: 33-1228-71
This Door Bumper is fully molded and designed from the original part for superior fitment. This rubber bumper attaches to the vehicle body to support / cushion the door closure. Usually requires two (2) bumpers each per vehicle.
1/4" Universal Mounting Pad
p/n: 70-0308-17
This Universal Mounting Pad is used for lights, hinges, brackets, and other bright work when no molded pad is available. Manufactured with a special edge lip to hug bright work when clamped down. Shape outline to suit application.
Door Bumper
p/n: 33-1227-71
This Door Bumper is fully molded and designed from the original part for superior fitment. The twin retainer style rubber bumper attaches to the vehicle body to support/cushion the door closure. Usually requires two (2) bumpers each per vehicle.
7/8" Trunk Bumper
p/n: 33-0293-87
This 7/8" Trunk Bumper is a quality reproduction of the original factory part. Self-retaining bumper is manufactured to OEM specifications to install for an authentic fit, finish, and function.
7/8" Trunk Bumper
p/n: 33-0990-87
This 7/8" Trunk Bumper is a quality reproduction of the original factory part. Self-retaining bumper is manufactured to OEM specifications to install for an authentic fit, finish, and function.
Brake Adjustment Hole Cover Plug
p/n: 70-1092-24
A quality molded rubber Brake Adjustment Hole Cover Plug that inserts into brake adjustment hole in the backing plate. Most models with drum brakes. Length: 1.25 inches. Height: .875 inches.
Lock Cylinder Gasket
p/n: 60-0641-69
This Lock Cylinder Gasket is die cut from one-thirty-second (1/32) inch neoprene.
15/16" Trunk Bumper
p/n: 33-0350-87
This 7/8" Trunk Bumper is a quality reproduction of the original factory part. Bumper fits to the rear compartment lid, lower corners on lid. Two (2) per car. Manufactured to OEM specifications to install for an authentic fit, finish, and function.