Steering Column Spacer
p/n: 60-0563-32
Spacer, steering column to dash at U-clamp.Length: 2.50 inches.
Upper Control Arm Bumper
p/n: 20-2727-32
This Upper Control Arm Bumper is designed from the original part for superior fitment and function. A molded rubber bumper which serves as a bump stop for the front suspension.
Lower suspension arm dust seal
p/n: 70-0625-32
Dust seal, lower suspension arm bushing. Four (4) required per car.
Front Axle Bumper
p/n: 20-1577-33
This Front Axle Bumper is a quality reproduction of the original factory part. These bottoming bump stops are dense rubber blocks that mount with a stud to a front axle bracket.
Front Suspension Bumper
p/n: 20-0034-32
Bumper, front suspension upper arm. Three eighths (3/8) inch by three fourths (3/4) inch bolt, twenty four (24) threads.
Axle Rebound Pad
p/n: 20-0833-32
Bumper, front axle. Fully molded with retaining bolt. Typically order two (2) per truck.
Control arm bushing
p/n: 20-1293-32
Bushing, control arm. Upper inner front. One (1) required per side.
Control arm bushing
p/n: 20-1280-32
Bushing, control arm. Upper inner rear. One (1) required per side.
Front Suspension Bumper
p/n: 20-0080-32
Bumper for front suspension upper arm. Measures three eighths (3/8) inch by sixteen (16) by eleven sixteenths with (11/16) inch bolt thread.
Axle Rebound Pad
p/n: 20-2730-32
Bumpers, outer rear axle. Mounts on frame rail. Push in type. Two (2) required per car.
Axle Rebound Pad
p/n: 20-2729-32
Bumper, outer rear axle. Mounts on frame rail. Push in type. Two (2) required per car.
Lower Suspension Arm Dust Seal
p/n: 70-0624-32
Dust seal, "O" ring. Lower suspension arm pin bushing. Four (4) required per car.Height: .25 inches.
Bumper - Front Lower Suspension
p/n: 20-2475-32
This Front Lower Suspension Bumper is designed from the original part for superior fitment and function. For the front lower control arm, bumper measures 2" tall and 1-15/16" wide.
Front or Rear Axle Bumper
p/n: 20-1576-33
This Front or Rear Axle Bumper is designed from the original part for superior fitment, finish and function. An exact reproduction of original. Typically order two per vehicle.
Front suspension bumper
p/n: 20-1062-32
Bumper, front suspension. Bumper section is 1-5/8" tall, 2" long, and 1-3/8 wide.
Axle Rebound Pad
p/n: 20-1287-32
Bumper, rear spring and axle. 1957-59: Full size Fords: Five (5) required per car (1 in center, 2 each side).
Upper Control Arm Bumper
p/n: 20-2725-32
Upper Control Arm Bumper made with top quality rubber. Includes nut.
Front suspension bushing
p/n: 20-2471-32
Seal, front suspension. Inner upper arm.Qty Required:4 Four (4) required per car.
Front suspension bushing
p/n: 20-2474-32
Seal, front suspension lower control arm outer. Four (4) required per car.
Control Arm Bushing Seal
p/n: 60-0095-32
Seal, lower control arm pivot bolt bushing. Four (4) per car.Width: .1875 inches.
Control arm bushing seal
p/n: 60-0094-32
Seal, upper and lower control arm cross shaft bushing, at inner end of arm.1939-48: Lower only, all pass. (exc.
Front suspension bushing
p/n: 20-2470-32
Seal, front suspension. Inner lower arm.Qty Required:4 Four (4) required per car.
Front suspension bushing
p/n: 20-2473-32
Seal, front suspension outer upper arm. Four (4) required per car.
9/16" Frame Grommet
p/n: 32-0414-32
This Frame Grommet is fully molded and designed from the original part for superior fitment and seal. Designed for the Bijur Lubricator delivery tube to run thru the frame at various places.