Antenna Mount Pad
p/n: 60-0159-21
Pad, antenna mounting. For fender location. One and five eighths (1-5/8) inch outside diameter.
Battery Hole Cover Seal
p/n: 20-0555-21
This Battery Hole Cover Seal is designed from the original part for superior fitment and seal. This part seals the battery hole cover to the vehicle floor.
Battery Clamp Cover
p/n: 70-0095-21
This Battery Clamp Cover helps to protect the nearby metal and finish. Fully molded from high-quality EPDM rubber to ensure durability. Good copy from an original part.
Antenna Mount Pad
p/n: 60-0338-21
This Antenna Mount Pad is a high-quality reproduction of the original factory part. This mount pad installs between the antenna mounting base and fender to protect the surface.
Coil wire sleeve
p/n: 40-0336-21
Nipple, sparkplug wire at sparkplug, for right angle plug terminal. This is an exact copy of the style used at the time. Not a modernistic makeover.
Starter Button Cover
p/n: 60-0358-21
Cover, starter rod button, round slip over type. One and seven sixteenths (1-7/16) inch outside diameter. Good copy with bow tie center.
Solenoid Plunger Boot
p/n: 60-0567-21
Boot, solenoid plunger, starter switch at starter.Height: 1.625 inches.
Antenna grommet
p/n: 70-1865-19
Grommet, antenna mounting. Fits all models with power antenna. Used with our #70-0756-19.
Spark plug retaining ring
p/n: 30-0352-21
Retaining ring, spark plug wire. Two (2) per car.Chevrolet 1935-48 Retaining ring, spark plug wire. Two (2) per car. All models.
Horn Button Contact Cushion
p/n: 18-0027-21
Cushions, horn contact plate.Qty Required:3 Width: 1.0 inches.
Antenna Mount Pad
p/n: 50-0168-21
Pad, antenna mounting over windshield, one and thirteen sixteenths (1-13/16) inch outside diameter, one and one fourth (1-1/4) inch inside diameter.
Antenna Mount Pad
p/n: 30-0502-21
Pad, antenna mounting on fender. For fender mounted antennas only.
Starter Pedal Bellows
p/n: 60-0210-21
This Starter Pedal Bellows is designed from the original part for an authentic fit, finish, and appearance. This bellows fits to the starter pedal shaft to floorboard.
Antenna Mount Pad
p/n: 60-0050-21
This Antenna Mount Pad is a high-quality reproduction of the original factory part. This mount pad installs between the antenna mounting base and fender to protect the surface.
Electrical Terminal Boot
p/n: 30-0279-41
This Electrical Terminal Boot is designed from the original part for superior fitment and seal. This boot works to cover and protect electrical terminal connections.
Battery Cable Grommet
p/n: 40-0333-21
Grommet, battery hot cable through frame. Three fourths (3/4) inch inside diameter for one and three sixteenths (1-3/16) inch hole through frame.
Coil wire sleeve
p/n: 70-1179-21
Sleeve, coil wire to distributor. Fluted to match upper water hoses rubber only.
Spark Plug Wire Spacer
p/n: 70-0394-21
This Spark Plug Wire Spacer is designed from the original part for superior fitment and function. This spacer fits spark plug wires into the organizer bracket.
Spark plug grommet
p/n: 70-1181-21
Grommet, spark plug and coil wire at distributor cap outlets. For seven (7mm) millimeter, later years.
Spark plug grommet
p/n: 70-1180-21
Grommet, spark plug & coil wire at distributor cap outlets. For nine (9mm) millimeter wire, earlier years.
Starter Solenoid Cable Rubber Boot
p/n: 70-0704-21
This Starter Solenoid Cable Rubber Boot is designed from the original part for superior fitment and function. This boot covers and protects the battery cable at the starter solenoid connection.
Insulator
p/n: 30-0404-48
Insulator, used on various places on vehicle. Uses 10 to 14 per car running board to frame bracket. Replaces factory #324851.
Instrument Bezel To Bezel Glass Seal
p/n: 70-4941-88
This Instrument Bezel To Bezel Glass Seal is designed from the original part for superior fitment and seal. This part seals the glass to the Instrument Panel / Bezel.
9/16" Battery Strap Grommet
p/n: 32-0491-21
This Battery Strap Grommet is fully molded and designed from the original part for superior fitment and seal. This grommet is made from high-quality EPDM dense rubber. Designed for the battery retaining hold-down bolt.
1-1/8" Antenna Hole Plug
p/n: 35-0327-45
This Antenna Hole Plug is fully molded and designed from the original part for superior fitment and seal. Designed for antenna mounting for inner fender at shroud, vehicles without a fender-mounted antenna.
1/2" Wiring Grommet
p/n: 32-0161-21
This Wiring Grommet is fully molded and designed from the original part for superior fitment. This grommet is made from quality dense rubber to provide excellent durability. Designed for the spark plug wire organizer bracket.
1" Firewall Grommet
p/n: 32-0320-21
This Firewall Grommet is fully molded and designed from the original part for superior fitment and seal. Designed for firewall applications such as running the wiring through the front body brace, right and left.
1" Antenna Grommets
p/n: 32-0390-21
This Antenna Grommet is fully molded and designed from the original part for superior fitment and seal. This grommet is made from high-quality EPDM dense rubber to provide excellent durability.
7/8" Wiring Grommet
p/n: 32-0002-21
This Wiring Grommet is fully molded and designed from the original part for superior fitment and seal. This grommet is made from high-quality EPDM dense rubber to provide excellent durability.
11/16" Wiring Grommet
p/n: 32-0003-21
This Wiring Grommet is fully molded and designed from the original part for superior fitment and seal. This grommet is made from high-quality EPDM dense rubber to provide excellent durability.
31/32" Firewall Grommet
p/n: 32-0133-21
This Firewall Grommet is fully molded and designed from the original part for superior fitment and seal. This grommet is made from high-quality EPDM dense rubber. Designed with wide spacing to pass electrical wiring and cables through metal frame.
Antenna Mount Gasket
p/n: 70-5054-19
This Antenna Mount Gasket is a high-quality reproduction of the original factory part. This mounting gasket installs between the antenna mounting base and fender to protect the painted surface.