Anti-Rattle Gravel Guard Deflector - Front or Rear Bumper
p/n: 70-0569-30
Manufactured to OEM standards, this Anti-Rattle Gravel Guard Deflector is for the front or rear bumper mounting bar depending on vehicle model. Metal with rubber covered end. Installs for an authentic fit and finish.
Bumper Grommet
p/n: 30-0039-28
Grommets, front or rear bumper. On models without trunk racks. Two (2) pair used per car if needing both front and rear bumper grommets.
Bumper Grommet
p/n: 10-0167-28
Grommets, front and rear bumper arm. Fully molded rubber, slightly angular.
Bumper Grommet
p/n: 40-0047-30
Grommets, front or rear bumpers, right and left. Two (2) pair used per car if needing both front and rear bumper grommets. Fully molded rubber.
Bumper Grommet
p/n: 40-0048-30
Grommets, bumper. Some front and some rear, right and left. Fully molded rubber.
Bumper Seal
p/n: 70-0978-45
Filler valance or deflector, rear. Extruded rubber to correct cross section. Fifty five (55) inches long.Length: 55.0 inches. Height: .28125 inches.
Bumper Seal
p/n: 70-0563-45
Filler valance or deflector, rear. Eight (8) inches long (cut shorter where required), three (3) to four (4) required per car.
Bumper Support Bar Pad
p/n: 70-0993-30
Bumper, impact bar end to body, for rear bumper. Fully molded rubber. Two inches (2") length by seven sixteenths inch (7/16") width by eleven sixteenths inch (11/16") height.
Bumper Support Bar Pad
p/n: 60-0420-30
Pads, rear bumper bar, inner, to quarter panel. Fully molded rubber.
Chrome Bumper To Body Splash Shield Filler
p/n: 70-4858-47
This Chrome Bumper To Body Splash Shield Filler is designed from the original part for a superior fitment. This bumper filler is approximately fifty-eight and three-eighths (58-3/8") inches long and fits between the vehicle body and the chrome rear bumper.</p>
Fender Bumper
p/n: 33-0545-30
Bumper, fender extension to quarter panel. Fully molded rubber. One and one fourths inch (1-1/4") length by eleven sixteenths inch (11/16") base diameter.
Front and Rear Bumper Spacer
p/n: 70-0184-30
Spacer or mute, front and rear bumper mounting bar to gravel deflector. Fully molded rubber. Two and nine sixteenths inch (2-9/16") outside length by seven eighths inch (7/8") width by thirteen sixteenths inch (13/16") height.
Front Bumper Gravel Shield Mute
p/n: 30-0399-29
These Front Bumper Gravel Shield Mutes are fully molded out of quality EPDM rubber. They are sold as a pair to fit on the outer bumper brackets. Designed to slide over the outer bumper to put tension on the bottom of the shield to prevent rattle.
Front Bumper Grommet
p/n: 27-0004-28
Grommet, front or rear bumper. Hollow construction, perfect fit. Note: In 1935 this grommet is used on the front bumper. In 1937-1938: this bumper is used on the rear bumper.
Front Bumper Grommet
p/n: 27-0054-28
Grommet, front bumper. Fully molded rubber, detailed and flanged as original.
Gravel Shield
p/n: 60-0524-30
This Gravel Shield is designed from an original part so it fits correctly. The seal installs to the rear apron to bumper. Sold as a sixty-six (66) inch strip.
Gravel Shield Bumper
p/n: 33-0286-30
Bumper, rear gravel shield, anti-rattle. Five (5) or more used per car. Fully molded rubber. Replaces factory #1320392.
Plastic body filler
p/n: 70-2265-30
Rear bumper corner. Seals between body and bumper on each end. Fully molded with proper details of long lasting rubber. Replaces #1387314-5.
Rear Bumper Arm Grommets
p/n: 20-2170-29
This Rear Bumper Arm Grommet pair is designed from the original part for an authentic fit, finish, and appearance.
Rear Bumper End Filler Set
p/n: 70-3769-30
This four (4) piece Rear Bumper End Filler set is designed from the original part for a superior fitment level. These die cut masticated rubber pieces fit to the left and right bumper ends between the rear bumper and the vehicle body.
Rear Bumper End Fillers
p/n: 70-3774-30
This two (2) piece Rear Bumper End Filler pair is designed from the original part for a superior fitment level. These die cut masticated rubber pieces fit to the left and right bumper ends between the rear bumper and the vehicle body.
Rear Bumper End Fillers
p/n: 70-2792-45
This Rear Bumper End Filler pair is designed from the original part for superior fitment and function. Filler pieces are die cut from quality masticated rubber to authentic original dimensions. These filler pieces fit behind each rear bumper end of the vehicle.
Rear Bumper Filler
p/n: 16-0004-30
Filler, rear bumper bar to body. U-shaped channel specially molded to conform to clearance in sheet metal. Fully molded rubber. Four and one fourths inch (4-1/4") length by two and one half inch (2-1/2") width by three eighths inch (3/8") height.
Rear Bumper Fillers
p/n: 70-4911-47
This Rear Bumper Filler pair is designed from the original part for a superior fitment level. These fully molded end pieces fit to the left and right bumper ends between the rear bumper and the vehicle body.
Rear Bumper Gravel and Splash Guard Shields
p/n: 70-1279-30
This two (2) piece Rear Bumper Gravel and Splash Guard Shield pair is designed from the original part for superior fitment and seal. Twenty-two (22) inches long per side.
Rear Bumper Gravel Shield
p/n: 60-0173-30
This Rear Bumper Gravel Shield, also known as a rear bumper face bar-to-body seal, is made of high quality dense rubber. Fully molded rubber with all original features.
Rear Bumper Gravel Shield
p/n: 60-0213-30
This Rear Bumper Gravel Shield, also known as a rear bumper face bar-to-body seal, is made of high quality dense rubber. This seal is the exact profile as original.
Rear Bumper Grommet
p/n: 50-0061-29
Grommets, rear bumper, hollow construction, superb copy, three and one half (3-1/2) inch high. Similar to our #50-0086-29.Length: 4.25 inches.
Rear Bumper Grommet
p/n: 40-0112-30
Grommets, rear bumper symmetrical, right and left. Perfect detailing on both inner and outer surfaces. Fully molded rubber.
Rear Bumper Grommet
p/n: 40-0363-30
Grommet, rear bumper to body, right and left. Fully molded rubber.
Rear Bumper Grommet
p/n: 70-0144-29
Grommets, rear bumper (Some cars have this type, some have our #70-0164-29, sold separately. They are both interchangeable and original). Fully molded rubber.
Rear Bumper Grommet
p/n: 40-0180-30
Grommet, rear bumper support bar to gas tank apron. One and three fourths (1-3/4) inch inside diameter.
Rear Bumper Grommet
p/n: 30-0127-29
Grommets, rear bumper extension bar through rear fender for wrap around bumpers. Fully molded rubber w/ full detail as in original.
Rear Bumper Grommet
p/n: 70-0104-29
Grommets, rear bumper, right and left. Large type with one and one fourth (1-1/4) inch by five (5) inch openings.