Battery Clamp Cover
p/n: 70-0095-21
This Battery Clamp Cover helps to protect the nearby metal and finish. Fully molded from high-quality EPDM rubber to ensure durability. Good copy from an original part.
Quarter Window Vertical Leading Edge
p/n: 70-0141-58
This quarter to side window Vertical Leading Edge Weatherstrip pair is designed from the original part for superior fitment and seal. Slides into metal retaining channel attached to rear side window and seals between the front door window and the rear quarter window.
1-5/8" Firewall Grommet
p/n: 60-0385-20
This Firewall Grommet is used to run various wires through the firewall. Designed from original parts for excellent workmanship.
Brake Master Cylinder Push Rod Boot
p/n: 60-0180-24
This Brake Master Cylinder Push Rod Boot is made from high-quality Nitrile rubber for a precise, factory like fit for your classic vehicle. Manufactured to OEM specifications to install for an authentic fit and finish.
Body Mounting Pad
p/n: 50-0506-48
Pad, body mounting. Rubber with metal core, locating collar and metal sleeve as original. Metal sleeve is removable.
Hood Bumper Set
p/n: 33-0681-42
This ten (10) piece Hood Bumper set is designed from the original parts for superior fitment and function.
Taillight Lens Gasket
p/n: 70-3091-15
This Taillight Lens Gasket pair is designed from the original part for superior fitment and seal. This reproduction gasket fits between taillight lens & taillight housing.
Header Bow Weatherstrip - Hardtop
p/n: 70-3918-64
This Header Bow Weatherstrip is the top and front seal rubber across windshield header for removable hardtops. Fully molded with the proper, as original, cross section in top quality rubber.
1-7/16" Firewall Grommet
p/n: 60-0276-45
This Firewall Grommet is used to run the throttle rod and tube, oil pressure gauge pipe, heat indicator tube, and choke rod through the firewall.
Front Lower Engine Mount
p/n: 20-0596-11
This Front Lower Engine Mount is designed from original part for correct fitment and function. Rubber coated over a metal core for durability and proper engine vibration isolation.
Body Mount Isolator Pad
p/n: 70-0929-48
Body Mount Isolator Pad - Rubber with metal core and locating collar as original part. Part dimensions = Two and three sixteenths inch (2 3/16") square by one inch (1") overall height with thirteen sixteenths inch (13/16") inside bolt diameter. Does not include any fastener hardware.
Trunk Bumper
p/n: 70-0296-87
T-nut, trunk bumper in gutter at sides, brass core tapped 10-32 thread. Two (2) required per car. For models having partial weatherstrip in gutter of body.
Body Mounting Pad
p/n: 60-0382-48
Cushion assembly (body mounting pad). Rubber with metal core, locating collar and metal bolt as original. Metal bolt is removable, measures fifteen sixteenths inch (15/16") long when removed.
Directional & Parking Light Lens Gaskets
p/n: 70-3092-16
This Directional Turn Signal and Parking Light Lens Gasket pair is designed from the original part for superior fitment and seal. This reproduction gasket fits between the signal / parking light lens and the signal / parking light housing or bezel.
Metal Sleeved Grommet
p/n: 70-0203-41
Flanged rubber grommet with metal sleeve bushing. Used as part of the accelerator relay lever. Also used from 1959-61 on all Cadillac models as a bushing for the windshield wiper relay lever adaptor.
Rear Leaf Spring Insulator
p/n: 70-0980-32
This Rear Leaf Spring Insulator is an exact replacement for the upper and lower spring pad. Two and one half (2-1/2) inches wide, with cloth reinforcement. Four (4) used per car.
Vent Window Division Bar Weatherstrips
p/n: 20-0709-56
This Front Vent Window Division Bar / Post Weatherstrip pair is designed from the original part for superior fitment and seal. This piece mounts with rivets on the vertical division bar and seals as the vent window glass closes against it.