Door Bumper
p/n: 34-0131-37
Bumper, front door above the upper hinge on the upper radius of the door. Stiff-backed, retained by screw, mounted on door only.
Shift Lever Grommet
p/n: 50-0284-24
Grommet, shift lever insulator. One (1) per car. Three eighths (3/8) inch inside diameter by five eighths (5/8) inch barrel by one half (1/2) inch long.
5/8" Door Weatherstrip with Clips
p/n: 70-1112-73
This Door Weatherstrip with Clips is made made from high quality EPDM sponge rubber. Excellent for use on many different vehicle models. Available by the foot.
Tailgate Bumper - Upper and Lower
p/n: 70-1827-87
This upper / lower Tailgate Bumper is designed from the original part for superior fitment and seal. Fully molded with top quality EPDM rubber over corrosion resistant brass cores to ensure durability and function.
Lower Door and Fuel Tank Door Bumpers
p/n: 20-0004-71
Manufactured to OEM specifications this Lower Door and Fuel Tank Door Bumper pair installs for an authentic fit, finish and function. Five eighths (5/8") inches high. Installs on door jamb where rear of door closes against body and on rear lower part of door.
Hood Bumper
p/n: 27-0103-42
Bumper, hood to fender ledge. Uses four (4) per car.Width: 1.25 inches. Height: .9375 inches.
Body Bolt Cushion
p/n: 60-0189-48
This Body Bolt Cushion is used for each body bolt under frame bracket, to cushion washer and nut. Fully molded from top-quality EPDM rubber with a high level of fit and finish.
Window Stop Stem Bumper
p/n: 33-0540-62
This Window Stop Stem Bumper is fully molded and designed from the original part for superior fitment and seal. Designed as a window stop cushion for front and rear door, rear side and quarter windows as required.
Glovebox Link Bumper
p/n: 50-0367-88
This Glovebox Link Bumper is made to original specifications for an authentic fit and appearance. The glovebox check link bumper fits on the glovebox door arm.
Door Bumper
p/n: 50-0203-41
This Door Bumper is used for the fuel filler door on the rear fender. Molded from top-quality EPDM rubber over a steel core for durability. These bumpers are screw retained.
Parking Light Housing Gaskets
p/n: 20-0612-16
This Parking Light Lens Gasket pair is designed from the original part for superior fitment and seal. This reproduction gasket fits between the Parking Light Housing or Bezel and the body of the vehicle.
Adjustable Hood Bumper
p/n: 70-0973-42
This Adjustable Hood Bumper is a quality reproduction of the original factory part. This rubber bumper attaches to the front fender to support / cushion the hood closure. 1957-1958 models use four (4) per vehicle. 1959-1960 models use two (2) per vehicle.
Multi-Purpose Clips
p/n: 70-4802-45
A ten (10) piece set of Multi-Purpose Clips. Commonly used to retain Hood to Cowl Weatherstrips or Inner Fender Splash Panels.
Shifter Bushing Set - Column Shift
p/n: 20-1435-26
This Shifter Bushing Set is designed from the original part for superior fitment and function. This bushing set will restore and tighten that loose and sloppy column shift gear selector to a like new condition.
Headlight dimmer switch pad
p/n: 70-0930-14
Pad, headlight dimmer switch. Rubber slip-over cover for floor mounted switch.
Spark Plug Wire Spacer
p/n: 70-0394-21
This Spark Plug Wire Spacer is designed from the original part for superior fitment and function. This spacer fits spark plug wires into the organizer bracket.
1-11/16" Main Harness Firewall Grommet
p/n: 70-2606-20
This Firewall Grommet fits to the engine firewall where main wire harness plugs in. Designed from the original part for superior fitment and finish.
Instrument Panel Grommet
p/n: 70-1654-88
Grommet, instrument panel to windshield frame. Two (2) to six (6) required.Length: 1.3125 inches. Width: 1.0625 inches.
Hood Bumper
p/n: 50-0205-42
This Hood Bumper is the adjustable type for the front of the hood. Used to support/cushion the hood closure. Cadmium plated bolt (5/16)-18 x 1-1/4". Excellent appearance with authentic details like original.
Upper Control Arm Bumper
p/n: 20-2725-32
Upper Control Arm Bumper made with top quality rubber. Includes nut.
Parking light lens gasket
p/n: 20-0608-16
Gaskets, parking light lens. Useage: 1957-63: Style-Side Trucks 1957-58: F100-600 Trucks
Rear View Mirror Mounting Pad
p/n: 70-3082-70
This single Rear View Mirror Mounting Pad To Door gasket is designed from the original part for superior fitment and seal. The gasket is precision die cut to the original specifications. This gasket is for one (1) door mounted rear view mirror.
Cowl to Fender Seal
p/n: 20-0031-31
Seal, right front fender apron to frame. Includes staples for installation.
Tailgate Bumper
p/n: 70-1910-87
This Tailgate Bumper is designed from the original part for superior fitment, finish and function. This station wagon tailgate bumper is commonly used on GM station wagon models.
Door Handle Gasket Set
p/n: 60-0640-69
This Door Handle Gasket Set is designed from the original part for superior fitment and seal. This six (6) piece gasket set will do two (2) doors.
Body Mounting Pad
p/n: 70-2234-48
Pad, body mounting to chassis. Fully molded rubber, square type. Six (6) or more are used per car. Two and three sixteenths inch (2 3/16") square by three fourths inch (3/4") inside diameter hole by one half inch (1/2") inch height.
Tailgate Bumper
p/n: 20-0694-45
These Tailgate Bumpers are sold as pair. The bumpers fit in brackets and comes with chains.
Hood Bumper
p/n: 50-0489-42
Bumper, hood to fender ledge. Number required varies. Molded rubber type.Width: 1.5 inches. Height: 1.0 inches.
Body Mount Isolator
p/n: 70-2232-48
Isolator, body mounting to chassis. Fully molded rubber. One and seven eighths inch (1 7/8") outside diameter by fifteen sixteenths inch (15/16") inside hole diameter by nine sixteenths inch (9/16") height.
Body Mounting Pad
p/n: 70-2233-48
Pad, body mounting to chassis. Fully molded rubber. One and seven eighths inch (1 7/8") outside diameter by eleven sixteenths inch (11/16") inside hole diameter by nine sixteenths inch (9/16") height.
Body Mount Isolator Pad
p/n: 50-0507-48
Isolator, body mounting. Fully molded rubber. Two inches (2") outside diameter by seven eighths inch (7/8") inside hole diameter by three fourths inch (3/4") height.
Gearshift Bushing
p/n: 60-0237-24
This Gearshift Bushing is fully molded and designed from the original part for superior fitment and seal. This bushing is made from high-quality EPDM dense rubber to provide excellent durability. Designed for the gearshift shaft lever, large type.
Door Bumper
p/n: 20-0003-71
Bumpers, door. Seven sixteenths (7/16) inch high. Fits on door jamb where rear of door closes against body and on rear lower part of door.
Bumpers - Filler Door/Lower Door/Rear License Plate Support
p/n: 20-1302-41
A rubber Bumper pair designed from the original part for superior fitment, finish and function. Fits to the lower door and / or the fuel filler cover and / or the license plate support. Type with threaded end.
Axle Rebound Pad
p/n: 20-1287-32
Bumper, rear spring and axle. 1957-59: Full size Fords: Five (5) required per car (1 in center, 2 each side).
Gearshift Knob
p/n: 20-0521-24
This black column shift lever Gearshift Knob is designed from the original part for a superior fit and finish. This sphere shaped reproduction part is a direct push on replacement for that broken, aged-out original knob.
Strut Rod Bushing
p/n: 50-0522-27
Bushing, strut rod at drive shaft tube. Two (2) per car required.Length: 1.65625 inches.
Gearshift Knob
p/n: 20-0629-24
This white column shift lever Gearshift Knob is designed from the original part for a superior fit and finish. This sphere shaped reproduction part is a direct push on replacement for that broken, aged-out original knob.
Dimmer Switch Grommet
p/n: 40-0083-88
This Dimmer Switch Grommet is used during carpet installations in automotive restorations. Made from high-quality EPDM dense rubber to provide excellent durability. Includes a wide flange for floor dimmer switch fitments.
Clutch or Brake Pedal Pad
p/n: 20-0848-22
This reproduction Clutch and/or Brake Pedal Pad slips over the full perimeter of the pedal for a precise, factory fit. A perfect reproduction to replace worn original pedal pads. Manufactured in quality black rubber.
Door Handle Gasket Set
p/n: 27-0102-69
This Door Handle Gasket Set is designed from the original part for superior fitment and seal. This six (6) piece gasket set will do two (2) doors.
Splash Apron / A-Arm Dust Shield
p/n: 70-2507-45
This two (2) piece Splash Apron / A-Arm Dust Shield Filler set is designed from the original part for superior fitment and seal. Filler pieces are die cut from quality masticated rubber to authentic original dimensions. Pieces fit over suspension a-arms and inside front inner fenders.
Outside Door Handle Mounting Pads
p/n: 20-0568-69
This Outside Door Handle Mounting Pad set is designed from the original part for superior fitment and function. This four (4) piece molded rubber set does two (2) doors.
Front Stabilizer Bar End Link Set
p/n: 20-0037-33
This eleven (11) piece Front Stabilizer Bar End Link Set is designed from original parts so it fits correctly. Two (2) kits / sets required per car as one (1) kit / set services one side of front stabilizer bar.
Fuel Filler Neck Grommet
p/n: 20-0585-39
This Fuel Filler Neck Grommet is designed from the original part for superior fitment and seal. This grommet fits around the vehicles fuel filler neck between the filler neck and vehicle body.
Transmission Mount
p/n: 70-2058-25
This Transmission Mount is a new aftermarket replacement mount manufactured to meet or exceed factory specifications.. One (1) required per vehicle.
Hood Bumper
p/n: 27-0098-42
Bumper, hood front to radiator ledge, adjustable. Includes plated bolt and rubber cushion.Length: 2.1875 inches.
Parking Light Lens Gaskets
p/n: 20-1239-16
This Parking Light Lens Gasket pair is designed from the original part for superior fitment and seal. This reproduction gasket fits between the Parking Light Lens and the Parking Light Housing or Bezel.
Exhaust Tailpipe Hanger Strap
p/n: 60-0308-13
This Exhaust Tailpipe Hanger Strap is made from high-quality rubber for a precise, factory like fit for your classic vehicle. Muffler/tailpipe system, reproduction strap type is manufactured to OEM specifications.
Tie Rod Dust Covers
p/n: 20-2484-36
This Tie Rod Dust Cover, drag link seal, is sold as a four (4) piece set. The seals are designed from originals for proper fitment.
Parking Light To Fender Mounting Pads
p/n: 20-1240-16
This Parking Light To Fender Pad pair is designed from the original part for superior fitment and seal. These reproduction gaskets fit between the parking light assembly and the vehicle fender on each side.
Hood bumper
p/n: 20-0041-42
Bumpers, rear of hood to top of fender. Two (2) required per vehicle.Ford Cars 1961-64 Bumpers, rear of hood to top of fender. Requires 2 pair for hood.
Rear Lower Engine Mount
p/n: 60-0459-11
This Rear Lower Engine Mount is designed from original part for correct fitment and function. The mount is made from a dense rubber for durability and proper engine vibration isolation.
Folding seat bumper
p/n: 70-2579-88
Bumper, folding front seat frame rest cushion. Manufactured from dense rubber with a molded in metal retaining washer. Two (2) used per car.
Glovebox Door Check Grommet
p/n: 27-0105-88
This Glovebox Door Check Grommet is manufactured out of 100% EPDM dense rubber for durability. Designed from original for a proper fit.
Window Regulator | Accelerator Rod Seal
p/n: 60-0652-70
This Window Regular | Accelerator Rod Seal is used as a front window regulator seal for 1955-60 passenger cars with electric windows and for 1957-62 Corvette models. Used as an accelerator rod through toeboard seal for 1955-62 V8 only Corvettes.
Fuel Tank Filler Neck Grommet
p/n: 20-1298-39
This Fuel Filler Neck Grommet is designed from the original part for superior fitment and seal. This fully molded flexible rubber grommet fits around the vehicles fuel filler neck between the filler neck and vehicle body.
Hood to Cowl Weatherstrip
p/n: 20-1310-42
This Hood to Cowl Weatherstrip is designed from the original part for superior fitment and seal. An reproduction using the correct profile dense rubber extrusion.
Hood to Cowl Weatherstrip
p/n: 70-3959-43
This Hood To Cowl Weatherstrip has the proper rubber cross section and made from top quality rubber to ensure durability. Designed from the original part for a superior fitment and seal.
Rear Bumper To Fender Filler
p/n: 70-2501-45
This Rear Bumper To Fender Filler pair is designed from the original part for superior fitment and function. Filler pieces are die cut from quality masticated rubber to authentic original dimensions. These filler pieces fit behind each bumper end of the vehicle.
Decklid Top Cover Weatherstrip
p/n: 70-3922-67
This Decklid Top Cover Weatherstrip is designed from the original part for a superior fitment and seal. This seal mounts around the full perimeter of the soft top storage compartment.
Cowl Drain Gutter Hose Grommet
p/n: 33-0329-54
This Cowl Drain Gutter Hose Grommet is fully molded and designed from the original part for superior fitment and seal. This grommet is made from high-quality EPDM dense rubber to provide excellent durability.
Body Mounting Pad
p/n: 70-2165-48
Pad, body mount, lower bolt retaining. Rubber with metal washer molded in. Used on the bottom of most mounting locations.
Cowl Vent Gasket
p/n: 60-0601-54
Side cowl vent seal. One eighth (1/8) inch thick high quality sponge design.Length: 8.50 inches. Width: 5.375 inches.
Front Suspension Bumper
p/n: 20-0034-32
Bumper, front suspension upper arm. Three eighths (3/8) inch by three fourths (3/4) inch bolt, twenty four (24) threads.
Parking and Fog Light Lens Gaskets
p/n: 70-3159-16
This Parking and Fog Light Lens Gasket pair is designed from the original part for superior fitment and seal. This reproduction gasket fits between the Parking and Fog Light Lens and the Parking and Fog Light Housing or Bezel.
Rear Upper Engine Mount
p/n: 60-0463-11
This Rear Upper Engine Mount is designed from original part for correct fitment and function. Made of a high-quality EPDM dense rubber for durability and proper engine vibration isolation.
Fender Anti-Squeak Weatherstrip
p/n: 20-1864-45
This Fender Anti-Squeak Weatherstrip mounts between the front fender splash apron and the front fender. The weatherstrip is an exact reproduction of the original Ford part. Sold as a seventy-two (72") inch strip.