Run Channel Retaining Clip
p/n: 60-0374-58
This Run Channel Retaining Clip is designed from the original part for an authentic fit, finish and function. Clip fits at the end of door window run channel. Tempered spring steel.
Running Board Covers
p/n: 20-2200-49
This Running Board Cover matting is designed from the original part for superior fitment and seal. This cover pair is pre-molded and manufactured from top quality rubber.
Running Board Edge Seal
p/n: 30-0169-44
Liner, running board to body, (side apron to body seal). Set consists of two (2) pieces seven (7) foot long. One (1) inch width is after fold over.
Running Board Matting
p/n: 30-0428-49
This reproduction Running Board Matting pair is designed from the original part for superior fitment, finish and function. Fully molded with crowned blocks. Top quality rubber, flawless detail. No splicing or butting required.
Running Board Matting
p/n: 50-0146-49
Matting, running board, original pattern with material to come down over ends and sides.
Running Board Matting
p/n: 30-0449-49
This Running Board Matting is designed from the original part for superior fitment and a factory like appearance. Made from short wheel-base matting with extension pieces to make the full length cover.
Running Board Mounting Pad
p/n: 30-0405-48
Insulator, washer, running board to frame bracket bolt, lower. Ten (10) to fourteen (14) required per car.
Running Board Trim Strips
p/n: 30-0450-49
This Running Board Trim Strip set is designed from the original part for superior fitment and a factory like appearance. Trim strips are made from high quality stainless steel and this set includes retaining clips (not sold separately). For 148" Wheel Base models.
Running Board Trim Strips
p/n: 30-0396-49
This Running Board Trim Strip set is designed from the original part for superior fitment, finish and function. Manufactured with quality stainless steel and with retaining clips.
Shift Lever Grommet
p/n: 70-0769-26
Grommet, upper shift lever at steering column.Height: .25 inches.
Shock Absorber Arm Bushing
p/n: 60-0106-32
This Shock Absorber Arm Bushing is designed from the original part for superior fitment and function. Manufactured to OEM original standards.
Shock Absorber Arm Bushing
p/n: 30-0192-32
Bushing, shock absorber arm. Restore proper shock action.Height: 1.375 inches.
Shock Absorber Bushing
p/n: 70-0547-32
This Shock Absorber Bushing is manufactured with high-quality EPDM rubber to OEM specifications. The bushing is the double cone style. Designed from original part to ensure proper fit.
Shock Absorber Bushing
p/n: 70-0541-33
This Shock Absorber Bushing is manufactured with high-quality Nitrile rubber to OEM specifications. The bushing is the single cone style. Designed from original part and made of high-quality Nitrile dense rubber to ensure durability.
Shock Absorber Link Arm Bushing
p/n: 60-0216-33
This Shock Absorber Link Arm Bushing is designed from the original part for superior fitment, finish and function. This bushing is for double acting shock absorber arm links.
Shock and Stabilizer Grommet
p/n: 70-0274-33
This Shock and Stabilizer Grommet is fully molded using EPDM dense rubber. Designed from original with locating collar. Eight (8) required per car.
Shock and Sway Bar Grommet
p/n: 30-0193-33
Grommet, rear shock arm link (lower end), or rear sway bar link lower end. Shock arms used four (4) per car. If needed, sway bar used two (2) per car. Fully molded rubber.
Shock or Stabilizer Link Cross Pin Bushing
p/n: 50-0220-32
This Shock or Stabilizer Link Cross Pin Bushing is designed from the original part for superior fitment and function. A rubber bushing for shock absorber link cross pin or stabilizer cross link pin.
Side Deflector / Valance Rubber
p/n: 70-0092-45
This Side Deflector / Valance Rubber pair is designed from the original part for superior fitment and seal. Each deflector piece is approximately 6 feet long.
Side Roof Rail Weatherstrip
p/n: 40-0095-65
Weatherstrip, convertible top to side windows. Fifteen sixteenths (15/16) inch by five eighths (5/8) inch. Sold in twelve (12) foot strips only.
Side Roof Rail Weatherstrip
p/n: 70-0251-65
Weatherstrip, side window. Base fifteen sixteenths (15/16) inch wide but easily trims to more narrow channel if necessary.
Side Roof Rail Weatherstrip
p/n: 20-2225-65
Seal, top iron to door glass. One (1) inch wide by thirty (30) inch length.
Side Roof Rail Weatherstrip
p/n: 14-0001-80
Fifteen (15) foot strip for convertible side window fits aluminum retainer channel.
Side Roof Rail Weatherstrip
p/n: 30-0031-65
Weatherstrip, side window. Fits metal channel. Made of high-quality EPDM rubber. Twelve (12) foot strip.
Side Window Beltline Scraper Weatherstrips
p/n: 60-0566-58
These inner and outer Side Window Beltline Scraper Weatherstrips slide into the groove on top of the door's window opening and wipes the glass when window is raised and lowered. Four (4) piece set.
Side Window Roller
p/n: 70-0117-62
This Side Window Roller, anti-rattle roller, is manufactured using EPDM dense rubber to replace the original perfectly. The roller fits both styles of brackets.
Side Window Sash Channel
p/n: 70-0641-58
This Side Window Sash Channel is the u-shaped steel channel only, no filler. Sold in 4 foot strip, usually sufficient for two (2) windows.
Sliding Quarter Window Weatherstrip
p/n: 70-0353-78
This Sliding Quarter Window Weatherstrip is used for side window inner and/or outer, front and/or rear doors. Available in a 6ft. lengths.
Sliding Quarter Window Weatherstrips
p/n: 60-0398-78
These Sliding Quarter Window Weatherstrips mount vertically in vehicle body where leading edge of sliding window fits when closed. Right and Left sides rubber only.
Spare Tire Bumper
p/n: 70-0126-37
Rest pad, spare wheel cover, metal core, screw held type. Eight (8) required per car.Width: 1.75 inches. Height: 1.4375 inches.
Spare Tire Bumper
p/n: 70-0125-37
Rest pad, spare wheel cover, metal core, tab held type. Sixteen (16) required per car.Width: 1.75 inches. Height: .75 inches.
Spare wheel carrier grommet
p/n: 14-0015-37
Grommet, sidemount arm, spare wheel support arm through fender, right and left.
Spare wheel carrier grommet
p/n: 30-0334-37
Grommet, rear spare wheel carrier bracket. Two (2) per car. (Also order our #32-0355-37 separately).
Spare Wheel Mounting Pad
p/n: 30-0480-37
Cushion, spare wheel in fenderwell.1937: 12's only (2 pair required). 1938-39: 12's only (3 pair required).Length: 12.875 inches. Width: 3.0 inches.
Spare Wheel Mounting Pad
p/n: 30-0446-37
Pad, spare tire inner.Length: .875 inches. Width: .75 inches.
Spark plug grommet
p/n: 70-1180-21
Grommet, spark plug & coil wire at distributor cap outlets. For nine (9mm) millimeter wire, earlier years.
Spark plug grommet
p/n: 70-1181-21
Grommet, spark plug and coil wire at distributor cap outlets. For seven (7mm) millimeter, later years.
Spark plug retaining ring
p/n: 30-0352-21
Retaining ring, spark plug wire. Two (2) per car.Chevrolet 1935-48 Retaining ring, spark plug wire. Two (2) per car. All models.
Spring or Stabilizer Bushing
p/n: 11-0020-35
Bushing, spring bracket on frame (Auburn and Cord 810 & 812). Also used as a grommet, front stabilizer bar (Graham models 116 & 120). Fully molded rubber.
Spring shackle bushing
p/n: 30-0090-32
Bushing, spring shackle, for shackle and eye leaf of rear spring. Eight (8) required per car.
Spring shackle bushing
p/n: 30-0420-32
Bushing, spring shackle. Six (6) per car. Packard's "self flanging" type.
Spring shackle seal
p/n: 70-1125-33
Washer, front and rear spring shackle, seal for shackle pin. Constructed of neoprene.
Stabilizer Bar End Link Set
p/n: 60-0221-33
Twenty-two (22) piece Stabilizer Bar End Link set for both sides of one (1) vehicle, fits front or rear bar. Order two (2) sets for vehicles with front and rear stabilizer bars. Hex head bolt 3/8"-16 NF x 6-15/16" long. Comes with metal sleeve, metal cup washers and rubber grommets.
Stabilizer Bar End Link Set
p/n: 70-0567-34
Twenty-two (22) piece Stabilizer Bar End Link set for both sides of one (1) vehicle, fits front or rear bar. Order two (2) sets for vehicles with front and rear stabilizer bars. Hex head bolt. 5/16"-24NF x 7-5/8" long. Includes metal sleeves, cup washers and rubber grommets.
Stabilizer Bushing
p/n: 30-0484-33
Bearings, stabilizer front rod. Requires two (2) per car. Fully molded rubber.
Stabilizer Bushing
p/n: 60-0316-34
Bushing, front stabilizer shaft. Two (2) per car.Length: 1.875 inches. Width: 1.6875 inches. Height: 1.4375 inches.
Stabilizer Bushing
p/n: 30-0483-33
Bearings, stabilizer rear rod. Requires two (2) per car. Fully molded rubber.
Stabilizer Grommet
p/n: 70-0436-33
Grommet, front stabilizer bar link or rear shock link to axle. Fully molded rubber. Eight (8) required per car.
Stabilizer Shaft Link Bushing
p/n: 60-0317-33
This Stabilizer Shaft Link Bushing works to support the vehicle front stabilizer or sway bar shaft. Six (6) required per vehicle.
Starter Button Cover
p/n: 60-0322-21
This Starter Button Cover is designed from the original part for an authentic fit, finish, and appearance. A push on replacement to rod. Two (2") inch outside diameter.
Starter Pedal Bellows
p/n: 60-0210-21
This Starter Pedal Bellows is designed from the original part for an authentic fit, finish, and appearance. This bellows fits to the starter pedal shaft to floorboard.
Starter Pedal Button Cover
p/n: 60-0166-21
This Starter Button Pedal Cover is designed from the original part for an authentic fit, finish, and appearance. Rubber slip over type for old metal. Two (2") inch outside diameter.
Starter Pedal Pad
p/n: 25-0049-89
Pad, starter pedal. Original pattern, brown rubber, exact copy.Height: .50 inches.
Starter Solenoid Cable Rubber Boot
p/n: 70-0704-21
This Starter Solenoid Cable Rubber Boot is designed from the original part for superior fitment and function. This boot covers and protects the battery cable at the starter solenoid connection.
Steering Column Collar Grommet
p/n: 70-0682-88
This Steering Column Collar Grommet is designed from the original part for superior fitment and function. The grommet fits the steering column at toe board over carpet.
Steering Column Cushion
p/n: 60-0012-36
Grommet, steering column to cowl, for U-bolt clamp. Black rubber. For brown see our #60-0012-89.Height: 1.25 inches.
Steering Column Cushion
p/n: 40-0259-36
Pad, steering post bracket. One (1) per car. Cushions steering post clamp to instrument panel.Length: 3.50 inches.
Steering Column Floorplate
p/n: 70-0683-88
Cover or seal, rubber, steering column and column gearshift at toe board, under carpet.Length: 12.25 inches.
Steering Column Floorplate
p/n: 50-0260-36
Retainer, front floor mat on steering column (also called steering column floorplate). Black rubber. For brown see our #50-0260-89.Width: 4.3125 inches.
Steering Column Grommet
p/n: 60-0102-36
Grommet, steering column at floor (column shift). Black rubber. For brown see our #60-0102-89.
Steering Column Vacuum Shift Cylinder Boot
p/n: 60-0556-24
This Steering Column Vacuum Shift Cylinder Boot is designed from the original part for superior fitment, function and appearance. Perfectly engineered duplicate of original. Constructed of durable long lasting rubber. Length: 4-3/8" inches.
Steering Gear Pitman Arm Bushing
p/n: 60-0105-36
This Steering Gear Pitman Arm Bushing is designed from the original part for superior fitment and function. Fully molded with steel core.
Steering Knuckle Support Seal
p/n: 50-0525-36
Seal, steering knuckle support, upper or lower. Die cut one fourth (1/4) inch, four (4) used per car.Height: .25 inches.
Steering Knuckle Support Seal
p/n: 50-0199-35
Seal, steering knuckle support, upper pivot pin. Four (4) required per car.Height: .5 inches.
Steering knuckle support seal
p/n: 60-0089-32
Seal, steering knuckle support, upper. Four (4) per car.