Coil wire sleeve
p/n: 70-0109-21
Sleeve, coil wire to distributor. Fluted to match upper water hoses rubber only. V-12 & V-16 with coils mounted in radiator, V-8 with coils mounted horizontally on brace rods.
2-3/8" Firewall Grommet
p/n: 30-0056-21
This Firewall Grommet is made to run the ignition cable and thermometer tube through the firewall. Designed from the original part for superior fit and seal.
Cowl Vent Gasket
p/n: 30-0096-54
Gasket, top cowl vent. Closed cell sponge rubber. One half (1/2) inch by three fourths (3/4) inch. Rectangular cross section.
Hood Inner Center Rest Pad
p/n: 30-0222-42
This Hood Inner Center Rest Pad pair is designed from the original part for an authentic fit, finish, and appearance. Rubber only pads that fit original bracket.
Rigid Run Channels
p/n: 70-0347-58
This Rigid Run Channel pair is stainless beaded and mohair-lined to help eliminate window rattles and provide a smooth sliding surface for glass movement. Also works to protect the glass.
Radiator Mounting Pad
p/n: 30-0395-31
Spacer or Pad, radiator anchorage stud, upper stud. One (1) pair required per car.Length: 2.5625 inches.
Brake Cable Anti-Rub Cover
p/n: 60-0443-24
Sleeve, rear brake cable anti-rub. Six (6) piece set. One half (1/2) inch inside diameter, seven eighth (7/8) inch outside diameter.
Brake Cable Boot
p/n: 60-0156-24
Boot, front brake cable end at brake backing plate. Two and seven eighths (2-7/8) inches long.Length: 2.875 inches.
Gearshift Boot - Black
p/n: 20-0334-26
This reproduction Black Gearshift Boot is designed from the original part for an authentic fit, finish, and appearance.
Hood Corner Pad Set
p/n: 20-2015-42
This fourteen (14) piece Hood Corner Pad set is designed from the original parts for superior fitment and function. Includes grille area and cowl bumpers as required.
Hood Corner Pad Set
p/n: 20-2018-42
This twelve (12) piece Hood Corner Pad set is designed from the original parts for superior fitment and function. The set includes grille area and cowl bumpers as required.
Fuel Neck Grommet
p/n: 70-0404-39
Grommet, fuel filler neck. Fully molded rubber. Flat bottom has slight ridge (seam) along edge. Four and three eighths inch (4-3/8") outside diameter by two and three sixteenths inch (2-3/16") inside hole diameter by five eighths inch (5/8") height.
Lower Door Weatherstrip
p/n: 20-2118-73
This three (3) piece lower door weatherstrip set is designed from original parts for superior fitment and seal. These lower seals mount directly to the lower door bottom for front and rear doors.
Taillight Mounting Pad
p/n: 50-0078-15
Taillight mounting pad. Excellent copy with proper lip at edge. Replaces #1273863. Customer must cut holes for wires, bulb, screws etc as required.
Hood Bumper
p/n: 40-0164-42
Pad, hood panel center bracket. Hollow, to fit over original steel bracket.Length: 1.375 inches. Width: 1.375 inches.
Transmission Mounting Pad
p/n: 11-0025-25
Mount, transmission. Original pattern, superior workmanship.
Hood Bumper
p/n: 30-0151-42
Bumpers, hood catch. Right and left.Length: 2.50 inches. Width: 1.4375 inches.
Flexible Run Channel
p/n: 20-1146-58
This Flexible Run Channel helps to eliminate window rattle, provides a smooth sliding surface for glass movement, and works to protect the glass. Stainless steel beaded. Available in sixty (60) inch strips.
Brown Gearshift Boot
p/n: 40-0111-89
Boot, base of gearshift lever. Brown rubber. For black see our #40-0111-88. Made separately to fit most of our gearshift floorplates. Copied from original.
Door - Gravel Shield - Running Board Weatherstrip
p/n: 60-0054-73
This Door - Gravel Shield - Running Board Weatherstrip is a anti-squeak bulb type extrusion with fitment for General Motors vehicles. A twelve (12) foot strip made of high-quality EPDM dense rubber and designed from original parts for superior fitment, finish and function.
Flexible Run Channel - 60 Inch
p/n: 20-1619-58
Channel, side window glass, vertical run. Flexible, felt lined, rubber covered channel. Available 60" lengths.
Hood Corner Pad
p/n: 27-0031-42
Pads, hood front corners, right and left. Metal core as original with integral mounting tabs for hole in hood corner.Width: 1.875 inches. Height: .
Brake Master Cylinder Filler Access Hole Cover
p/n: 60-0016-24
This Master Cylinder Access Hole Cover is designed from the original part for superior fitment and seal. Secures the Brake Master Cylinder Filler and Inspection Access Hole in the vehicle.