Door and Trunk Handle Gasket
p/n: 40-0132-70
Pad, door handle escutcheon. Two and five sixteenths (2-5/16) inch by one and seven sixteenths (1-7/16) inch.
Side Roof Rail Weatherstrip
p/n: 20-2225-65
Seal, top iron to door glass. One (1) inch wide by thirty (30) inch length.
Fuel Neck Grommet
p/n: 20-2177-39
Grommet, fuel filler neck. Fully molded rubber with small retaining lip. Three and five eighths inch (3-5/8") outside diameter by two and nine sixteenths inch (2-9/16") inside hole diameter.
Upper Engine Mount
p/n: 20-1538-11
This Front or Rear Upper Engine Mount reproduction is designed from the original part for superior fitment and durability. This mount fits between the engine and chassis to support the engine and reduce harmonic vibrations.
Door Handle Gasket
p/n: 40-0133-70
Pad, door handle escutcheon. Two and three fourths (2-3/4) inch by one and one fourth (1-1/4) inch.Width: 2.75 inches. Height: 1.25 inches.
Loom Wiring Grommet
p/n: 60-0255-14
Grommet, headlight loom through body sheet metal. Four (4) to six (6) per car.Length: .9375 inches.
Electrical Terminal Boot
p/n: 30-0279-41
This Electrical Terminal Boot is designed from the original part for superior fitment and seal. This boot works to cover and protect electrical terminal connections.
Door Bumper
p/n: 60-0048-71
Bumper, door side. Five eighths (5/8) inch by seven eighths (7/8) inch by one and seven sixteenths (1-7/16) inch. Two (2) door.
Black Door Lock Knob
p/n: 30-0251-71
Knob, inside door lock control, flexible rubber, black only.Height: 1.125 inches.
Axle Rebound Pad
p/n: 50-0302-35
Bushing, rear axle, anti-sway rod ends. Fully molded rubber. Four (4) required per car.
Shift Lever Grommet
p/n: 70-0769-26
Grommet, upper shift lever at steering column.Height: .25 inches.
Body Mounting Pad
p/n: 50-0131-48
Pad, body mounting. Fully molded rubber with locating collar. Two-inch (2") square by thirteen sixteenths inch (13/16") locating collar outside diameter by one half inch (1/2") locating collar inside diameter.
Coil wire sleeve
p/n: 70-1179-21
Sleeve, coil wire to distributor. Fluted to match upper water hoses rubber only.
Choke and Throttle Rod Grommet
p/n: 20-2279-88
This Choke and Throttle Rod Grommet is used where the choke and throttle pass through the dash. Designed from the original part for superior fit and seal.
1-3/8" Firewall Grommet
p/n: 70-0712-20
This Firewall Grommet is designed from the original part for superior fit and seal. Made from high-quality dense rubber to provide excellent durability. Two (2) holes in grommet.
Windshield Bumper
p/n: 34-0258-52
Bumper (stop), swing out windshield against dash. Steel core, nine sixteenths (9/16) inch diameter by five sixteenths (5/16) inch thick. Replaces #3681093. Two (2) per vehicle.
Engine Mount Bolt
p/n: 20-0309-11
This Engine Mount Bolt can be used for the front or rear. Hex head bolt drilled for cotter key.
Lower Engine Mount
p/n: 20-1539-11
This Lower Engine Mount is designed from original part for correct fitment and function. Rubber coated over a metal core for durability and proper engine vibration isolation.
1/8" x 7/8" Fabric Hood Lacing
p/n: 60-0578-42
This 1/8" x 7/8" Fabric Hood Lacing is high quality original style woven cotton hood to cowl lacing. This lacing has the slot to install a wire insert or fasten with rivets if so found originally. Available by the foot to accommodate any job.
3/16" x 3/4" Fabric Hood Lacing
p/n: 70-2221-42
This 3/16" x 3/4" Fabric Hood Lacing is made of a high-quality original style woven cotton. Available by the foot to accommodate any job.
License Light Socket Grommet
p/n: 50-0395-17
Grommet, license light socket.May fit earlier years.Height: .5 inches.
Front Engine Mounting Pad
p/n: 50-0229-11
This Engine Mount Pad is designed to original specifications with superior workmanship. Made of a high-quality EPDM dense rubber for durability and authentic fit.
Front and Rear Door Bumper
p/n: 34-0025-42
High quality steel core Front and Rear Door Bumper for front and rear body hinge pillar. Mounted by screw. For auxiliary use only where needed to prevent door rattles. Replaces factory #372341.
Side Window Run Channel
p/n: 70-1168-58
Side window run channel pre-flocked for 1/4" glass. Available by the foot.
Side Window Run Channel
p/n: 70-1169-58
Channel, side window, pre-flocked, 9/16" wide to accommodate metal frame side window. Available by the foot.
Door Check Link Rod End Stop Washer
p/n: 70-0384-70
A quality Door Check Link Rod End Stop Washer for door check mechanism. One and seven-sixteenths (1-7/16") inch diameter by three-sixteenths (3/16") inch thick.
Firewall Retainer
p/n: 30-0207-20
Fastener, firewall insulation. Three fourths (3/4) inch diameter head by one (1) inch long.Height: 1.0 inches.
2-1/4" Firewall Grommet
p/n: 32-0225-20
This Firewall Grommet is fully molded and designed from the original part for superior fitment and seal. This grommet is made from high-quality EPDM dense rubber to provide excellent durability.
Door Bumper
p/n: 34-0131-37
Bumper, front door above the upper hinge on the upper radius of the door. Stiff-backed, retained by screw, mounted on door only.
Fuel Tank Support Pad
p/n: 30-0482-41
This Fuel Tank Support Pad is made of a high quality EPDM dense rubber. This cushion is used to help reduce noise. Available by the foot.
Side Window Roller
p/n: 70-0117-62
This Side Window Roller, anti-rattle roller, is manufactured using EPDM dense rubber to replace the original perfectly. The roller fits both styles of brackets.
Body Mounting Pad
p/n: 70-0264-48
This Body To Frame Mounting Pad is designed from the original parts for superior fitment and function. Installs under body mount / washer below bracket. Fully molded high quality EPDM rubber.
Spark plug grommet
p/n: 70-1181-21
Grommet, spark plug and coil wire at distributor cap outlets. For seven (7mm) millimeter, later years.
1-5/8" Firewall Grommet
p/n: 32-0226-20
This Firewall Grommet is fully molded and designed from the original part for superior fitment and seal. This grommet is made from high-quality EPDM dense rubber to provide excellent durability. Designed for the handbrake cable.
Convertible Roof Rail Weatherstrip
p/n: 20-1636-65
This Convertible Roof Rail Weatherstrip is designed from the original part for superior fitment and seal. This window channel seal fits between windshield posts and door. Also fits along the top irons. This part is one (1) each. Five (5) individual pieces are required for the complete top.
Door Handle Grommet
p/n: 70-0009-69
Grommet, for outside door handle ferrule (our #70-0111-69, ordered separately). Molded rubber with cloth covering per original.
Brown Door Lock Knob
p/n: 70-0660-70
This is the Knob or push button for the inside door lock. The part fits over 1/8" steel rod to door lock. Neutral brown color that may be lacquered with other colors as required. A hard rubber part fits many different vehicles.
Starter Solenoid Cable Rubber Boot
p/n: 70-0704-21
This Starter Solenoid Cable Rubber Boot is designed from the original part for superior fitment and function. This boot covers and protects the battery cable at the starter solenoid connection.
Spark plug grommet
p/n: 70-1180-21
Grommet, spark plug & coil wire at distributor cap outlets. For nine (9mm) millimeter wire, earlier years.
Masticated Rubber Sheet
p/n: 70-0645-45
This Masticated Rubber Sheet is three-thirty seconds (3/32) inch thick. The rubber sheet contains random milled cotton cord reinforcement for front end splash aprons, etc.
1-9/16" Firewall Grommet
p/n: 32-1201-20
This Firewall Grommet is fully molded and designed from the original part for superior fitment and seal. This grommet is made from high-quality EPDM dense rubber to provide excellent durability. Typically used for wiring.
Rear Spring Thrust Washer
p/n: 40-0526-32
Thrust washer, rear spring. "Silent Block". Three sixteenths (3/16) inch thick. Seven eighths (7/8) inch by one and five eighths (1-5/8).
Taillight Lens Gasket
p/n: 20-1988-15
Gasket, taillight lens. Inner and outer seal. Enough for one taillight lens.
Shock and Stabilizer Grommet
p/n: 70-0274-33
This Shock and Stabilizer Grommet is fully molded using EPDM dense rubber. Designed from original with locating collar. Eight (8) required per car.
2-5/8" Run Channel Mohair Liner
p/n: 70-2863-58
This Run Channel Mohair Liner helps to reline the guide bars on the lock side of hardtops and convertibles. This mohair liner comes with a rubber backing and installs with adhesive to the division bars and channel. Available by the foot.
Insulator
p/n: 30-0404-48
Insulator, used on various places on vehicle. Uses 10 to 14 per car running board to frame bracket. Replaces factory #324851.
Steering Knuckle Support Seal
p/n: 50-0199-35
Seal, steering knuckle support, upper pivot pin. Four (4) required per car.Height: .5 inches.
13/16" Trunk Weatherstrip
p/n: 50-0161-85
This Trunk Weatherstrip was designed from an original part for a specific application but has many uses outside of its original purpose. Available by the foot.
Brown Door Lock Knob
p/n: 70-0354-70
This is the knob or button for the inside door lock control rod. Neutral brown color rubber, 3/32 inch hole. The part fits many different vehicles.
Rear Spring Thrust Washer
p/n: 40-0525-32
Thrust washer, rear spring. "Silent Block". Three sixteenths (3/16) inch thick. One (1) inch by one and three fourths (1-3/4) inch.
Peel-N-Stick Trunk Weatherstrip
p/n: 30-0356-WT
This trunk weatherstrip is designed from the original part for superior fitment and seal. The seal mounts around the full perimeter of the trunk directly to the body. Easy to install 3M Peel-N-Stick backing provides superior adhesion for reliable performance.
Door Check Link Rod End Stop
p/n: 70-0325-70
A quality Door Check Link Rod End Stop for rod type door check mechanism. One (1") inch diameter by three-eighths (3/8") inch thick with five-sixteenths (5/16") inch hole.
11/16" Roof Rail Weatherstrip
p/n: 70-1171-99
This available by the foot Roof Rail Weatherstrip measures eleven sixteenths inches (11/16") in height. It fits into a metal channel retainer. Note: Order twelve feet (12') for two (2) door models and fourteen feet (14') for four (4) door models.
Shock Absorber Arm Bushing
p/n: 60-0106-32
This Shock Absorber Arm Bushing is designed from the original part for superior fitment and function. Manufactured to OEM original standards.
Side Roof Rail Weatherstrip
p/n: 70-0251-65
Weatherstrip, side window. Base fifteen sixteenths (15/16) inch wide but easily trims to more narrow channel if necessary.
9/16" Door Edge Weatherstrip
p/n: 70-0411-73
This Door Edge Weatherstrip is made from high-quality EPDM sponge rubber. Excellent for use on many different vehicle models. Available by the foot.
Pressure Ring
p/n: 70-0261-69
Pressure ring (washer), sponge rubber, interior door handle and window regulator escutcheon. One and three fourths (1-3/4) inches outside diameter by three eighths (3/8) inch thick.
Wiper Transmission Gasket
p/n: 20-1609-53
Seal, wiper pivot shaft to roof or cowl. Small type. Replaces factory #11A-17541. Note: this part is used as a wiper pivot shaft to roof in 1937-1939. It is used as a wiper pivot shaft to cowl in 1941-1948.
11/16" Channel filler weatherstrip
p/n: 70-0075-57
Channel pad, window carrier, incorporating weatherstrip. Used for some side window lower channel. Available by the foot.
Brake Cable Shielding Cover - 2 Inch
p/n: 70-1701-24
This two (2) inch long Brake Cable Shielding Cover is designed install for an authentic fit, finish and function. Fits all models with seven sixteenths (7/16) inch outside diameter cable.
2-1/4" Body Hole Plug
p/n: 35-0863-45
This Body Hole Plug is fully molded and designed from the original part for superior fitment and seal. Designed for the trunk, however the generic shape makes this plug usable for a variety of applications.
5/8" Channel filler weatherstrip
p/n: 30-0507-57
Seal, door window frame, upper and rear. Used on some open models with metal frame around glass. Available by the foot.
Spare Wheel Mounting Pad
p/n: 30-0446-37
Pad, spare tire inner.Length: .875 inches. Width: .75 inches.
7/8" Window Weatherstrip
p/n: 70-1192-52
This Window Weatherstrip is for models with chrome reveal molding. Available by the foot.
1/2" Channel Filler Weatherstrip
p/n: 30-0154-57
Filler, for glass channel for convertible type windows with metal frame around one fourth (1/4) inch glass. Available by the foot.
Side Window Bumper
p/n: 60-0195-62
Anti-rattle, side window, inner and outer. Fits slot in outer door body metal and inner window frame (garnish molding).
7/8" Window Weatherstrip
p/n: 70-1191-52
This Window Weatherstrip is for models without chrome reveal molding. Available by the foot.
11/16" Channel Filler Weatherstrip
p/n: 70-0241-57
Weatherstrip, side window, double-lip seal type, used as filler for one fourth (1/4) inch glass in metal carrier channel. Available by the foot.
9/16" Channel filler weatherstrip
p/n: 70-0489-58
Weatherstrip, channel filler, door window sash channel and some quarter window sash channel. Special type with wide weatherstrip edge to be trimmed at assembly, when necessary. Available by the foot.
7/8" Windshield Weatherstrip
p/n: 70-1190-52
This Windshield Weatherstrip is for windows without chrome reveal molding. For a 2-piece windshield, select gasket for division bar. Available by the foot.
7/16" Rear Window Weatherstrip
p/n: 30-0044-77
This Rear Window Weatherstrip is made of a high-quality EPDM dense rubber. Extra light, plain channel for one fourth (1/4) inch glass. Three thirty seconds (3/32) inch thick wall. Available by the foot.
Spring shackle seal
p/n: 70-1125-33
Washer, front and rear spring shackle, seal for shackle pin. Constructed of neoprene.
3/4" Roof Rail Weatherstrip
p/n: 70-1170-99
This available by the foot Roof Rail Weatherstrip measures three fourths inches (3/4") in height. It fits into a metal channel retainer. Note: Order twelve feet (12') for two (2) door models and fourteen feet (14') for four (4) door models.
5/8" Window Weatherstrip
p/n: 70-1194-52
This Window Weatherstrip is for models with plain "U" channel five eighths (5/8) inch high. Available by the foot.
3/4" Windshield Weatherstrip
p/n: 40-0015-52
This Windshield Weatherstrip has a three eighths (3/8) inch wide opening and one eighth (1/8) inch diameter retaining bead, for metal frame around glass. Available by the foot.
3/4" Trunk Weatherstrip
p/n: 30-0356-85
This Trunk Weatherstrip is made from high quality EPDM sponge rubber. Excellent for use on many different vehicle models. Available by the foot.
1/2" Door Bottom Weatherstrip
p/n: 70-0066-73
This Door Weatherstrip is designed for the bottom of the door and is held in by a metal track or by clips. Available by the foot.
Rear spring pad
p/n: 30-0370-32
Separator, spring leaf, rear. Use as required, up to twenty four (24) needed per car.
Steering Knuckle Support Seal
p/n: 50-0525-36
Seal, steering knuckle support, upper or lower. Die cut one fourth (1/4) inch, four (4) used per car.Height: .25 inches.
Wheel Cover Cushion
p/n: 70-0633-38
Filler, wheel cover to wheel. Approximately two and one eighth (2-1/8) inches long each, twenty (20) required per car. (Five (5) per wheel cover).
11/16" Wiring Grommet
p/n: 32-0161-21
This Wiring Grommet is fully molded and designed from the original part for superior fitment. This grommet is made from quality dense rubber to provide excellent durability. Designed for the spark plug wire organizer bracket.
1/16" Sash Channel Filler - Cork
p/n: 70-1115-57
This 1/16" Sash Channel Filler offers the best quality cork product for your classic vehicle project. Manufactured to OEM specifications to install for an authentic fit and finish. Available by the foot.
1/2" Trunk Weatherstrip
p/n: 70-1106-99
This Trunk Weatherstrip is made from high-quality EPDM sponge rubber. Excellent for use on many different vehicle models. Available by the foot.
Run Channel Retaining Clip
p/n: 60-0374-58
This Run Channel Retaining Clip is designed from the original part for an authentic fit, finish and function. Clip fits at the end of door window run channel. Tempered spring steel.
Engine Mount Washer
p/n: 20-0442-11
This Front Upper Engine Mount Washer is made of steel. The large upper engine mount insulator sits in this special washer. Fits all Ford 6 cylinder and Flathead V-8 models.