Brown Steering Floorplate
p/n: 50-0260-89
Retainer, front floor mat on steering column (also called steering column floorplate). Brown rubber. For black see our #50-0260-36.
Bumper Grommet
p/n: 40-0047-30
Grommets, front or rear bumpers, right and left. Two (2) pair used per car if needing both front and rear bumper grommets. Fully molded rubber.
Bumper Grommet
p/n: 40-0048-30
Grommets, bumper. Some front and some rear, right and left. Fully molded rubber.
Bumper Support Bar Pad
p/n: 60-0544-30
A fully molded rubber Bumper Support Bar Pad. Thes part installs between the bumper support bar and bumper face bar at the mounting bolts. Use as required, eight (8) are needed for most cars.
Cadillac Motors pedal pad
p/n: 70-0076-22
Cadillac Motors pedal pads. Authentic straight diamond pattern. Especially good copy, fine detail.
Cadillac V-8 Pedal Pad
p/n: 70-0148-22
Cadillac V-8 pedal pads, clutch and brake. Another rare one we finally found to copy. Superior copy.
Carburetor Air Intake Hose
p/n: 70-0290-41
Hoses, carburetor air intake. Two (2) per car. Sixteen and three fourths (16-3/4) inches long, two (2) inches inside diameter one end, two and one fourth (2-1/4) inches inside diameter other end. Trim to proper length when installing.
Carpet Heel Plate
p/n: 70-0604-88
Heel mat, front carpet, driver's position.Length: 15.75 inches. Width: 6.25 inches.
Carpet Heel Plate
p/n: 40-0087-88
Heel pad for carpet. Identical to original. Five and three fourths (5-3/4) inch by ten and one half (10-1/2) inch, to be stitched in place.Length: 10.
Channel Filler Weatherstrip
p/n: 20-2091-62
This Channel Filler Weatherstrip is designed from the original part for superior fitment and seal. This door glass to body filler seal fits in the metal channel that holds the glass piece. Sold in a 36" strips.
Channel Filler Weatherstrip
p/n: 20-1633-62
Seal, door glass and stainless frame special. Top, bottom, and sides for one door.Width: .375 inches. Height: .625 inches.
Choke and Throttle Dash Grommets
p/n: 20-0347-41
This Choke and Throttle Dash Grommet pair mounts in the dash where the choke and throttle rods pass through the dash to keep rods from rattling.
Choke, Throttle and Starter Wiper Motor Grommet
p/n: 20-1561-20
This Choke, Throttle or Wiper Motor Grommet is designed from the original part for superior fitment and usage. A multi-purpose grommet, it fits into the vehicles firewall to provide a secure passthrough for the mechanical choke, throttle rod or wiper motor wiring.
Chrome Fender Welting - 25ft
p/n: 70-1101-44
Welting, fender, bright chrome vinyl, three sixteenths (3/16) inch bead, one and one half (1-1/2) inch width. Superior quality. Twenty five (25) foot roll. Typically used to attach two (2) fenders to body. For fifty (50) foot roll see our #70-1102-44.
Chrome Fender Welting - 50ft
p/n: 70-1102-44
Welting, fender, bright chrome vinyl, three sixteenths (3/16) inch bead, one and one half (1-1/2) inch width. Superior quality. Fifty (50) foot roll. Typically used to attach four (4) fenders to body. For twenty five (25) foot roll see #70-1101-44.
Clutch and Brake Pedal Bumpers
p/n: 60-0104-24
This Clutch and Brake Pedal Bumper is designed from the original part for superior fitment, finish and function. Pedal shank rides under floorboard. One and one-eighth (1-1/8") inch clearance for pedal shaft.
Clutch and Brake Pedal Pads
p/n: 60-0068-22
This reproduction Clutch and Brake Pedal Pad pair slips over the full perimeter of the pedal for a precise, factory fit. An oval style perfect reproduction to replace worn or damaged original pedal pads.
Clutch and Brake Pedal Pads - Black
p/n: 50-0049-22
This reproduction Clutch and Brake Pedal Pad pair slips over the full perimeter of the pedal for a precise, factory fit. A perfect reproduction to replace worn original pedal pads. Manufactured in quality black rubber.
Clutch and Brake Pedal Pads - BLACK
p/n: 25-0024-22
This reproduction Clutch and Brake Pedal Pad pair slips over the full perimeter of the brake pedal for a precise, factory fit. A reproduction with authentic type ribbing, to replace worn original pedal pads. Manufactured in Black rubber.
Clutch and Brake Pedal Pads - Black
p/n: 50-0054-22
This reproduction Clutch and Brake Pedal Pad pair slips over the full perimeter of the pedal for a precise, factory fit. A perfect reproduction to replace worn original pedal pads. Manufactured in quality black rubber.
Clutch and Brake Pedal Pads - Black
p/n: 40-0107-22
This reproduction Clutch and Brake Pedal Pad pair slips over the full perimeter of the brake pedal for a precise, factory fit. An oval style perfect reproduction to replace worn original pedal pads. Manufactured in Black rubber.
Clutch and Brake Pedal Pads - Bowtie Emblem
p/n: 60-0125-22
This reproduction Clutch and Brake Pedal Pad pair slips over the full perimeter of the pedal for a precise, factory fit. A perfect reproduction to replace worn original pedal pads. Manufactured in quality black rubber with Chevy bowtie in tread.
Clutch and Brake Pedal Pads - Brown
p/n: 50-0049-89
This reproduction Clutch and Brake Pedal Pad pair slips over the full perimeter of the pedal for a precise, factory fit. A perfect reproduction to replace worn original pedal pads. Manufactured in quality black rubber.
Clutch and Brake Pedal Pads - Brown
p/n: 50-0054-89
This reproduction Clutch and Brake Pedal Pad pair slips over the full perimeter of the pedal for a precise, factory fit. A perfect reproduction to replace worn original pedal pads. Manufactured in quality brown rubber.
Clutch and Brake Pedal Pads - BROWN
p/n: 25-0024-89
This reproduction Clutch and Brake Pedal Pad pair slips over the full perimeter of the brake pedal for a precise, factory fit. A reproduction with authentic type ribbing, to replace worn original pedal pads. Manufactured in Brown rubber.
Clutch pedal bumper
p/n: 60-0355-24
Bumper, clutch pedal shank under floorboard. Some commercial and utility models, compare with our #60-0104-24.
Coil wire sleeve
p/n: 40-0336-21
Nipple, sparkplug wire at sparkplug, for right angle plug terminal. This is an exact copy of the style used at the time. Not a modernistic makeover.
Coil wire sleeve
p/n: 14-0022-21
Sleeve, spark plug wires from distributor to wiring tube, rubber only.
Coil wire sleeve
p/n: 70-1179-21
Sleeve, coil wire to distributor. Fluted to match upper water hoses rubber only.
Convertible Front Header Bow Weatherstrip
p/n: 70-0157-64
This convertible soft top Front Header Bow Weatherstrip is designed from the original part for superior fitment and seal. This seal installs directly to the convertible soft top to seal to the windshield, INNER, right and left.
Convertible Front Header Bow Weatherstrip
p/n: 70-0138-64
This convertible soft top Front Header Bow Weatherstrip is designed from the original part for superior fitment and seal. This seal installs directly to the convertible soft top to seal to the windshield, OUTER, right and left. This weatherstrip is molded with necessary pre-drilled end hook and screw openings to the proper clearance.
Convertible Roof Rail Weatherstrip
p/n: 20-1636-65
This Convertible Roof Rail Weatherstrip is designed from the original part for superior fitment and seal. This window channel seal fits between windshield posts and door. Also fits along the top irons. This part is one (1) each. Five (5) individual pieces are required for the complete top.
Convertible Top - Arm Pad
p/n: 50-0319-67
Bottom pad, right and left side for 3rd bow folding post. Steel core with all original features. Quality rubber.
Convertible Top - Rest Block
p/n: 50-0318-67
Rest block, convertible top. Two (2) required per car. Fits into dovetail retainer. Length: 1.375 inches. Width: 1.125 inches.
Convertible Top - Resting Block
p/n: 20-2231-67
Pad, convertible top resting block. Used when top is down. One (1) required per vehicle.
Cowl Firewall Grommet
p/n: 20-1560-20
This Cowl Firewall Grommet fits into the upper section of the firewall for the main wiring harness. Also used to run the dash wires on the firewall and through the firewall.
Cowl Vent Gasket
p/n: 60-0087-54
Gasket, cowl vent, lip type. Sponge rubber, for three and seven eighths (3-7/8) inch by fifteen (15) inch cowl vent.Length: 15.0 inches. Width: 3.
Cowl Vent Gasket
p/n: 40-0225-54
This Cowl Vent Gasket is designed from the original part for superior fitment and seal. Installs for a like factory fit and finish.
Cowl Vent Gasket
p/n: 30-0179-54
Gasket, cowl vent, original labyrinth type, not sponge.Length: 14.75 inches. Width: 5.50 inches.
Cowl Vent Gasket
p/n: 30-0172-54
Gasket, cowl vent. Top quality sponge of correct section, cut to sufficient length for circumference of vent cover.
Cowl Vent Gasket
p/n: 14-0037-54
Gasket stock, cowl vent, high grade sponge of proper cross-section, (not molded into ring), approximately forty eight (48) inch strip per car.
Cowl Vent Gasket
p/n: 20-1613-54
This Cowl Vent Gasket is designed from the original part for superior fitment and seal. Manufactured to OEM specifications to install for an authentic fit and finish.
Cowl Vent Weatherstrip
p/n: 70-0224-54
Weatherstrip, cowl vent. Original solid rubber configuration, not a sponge substitute. A top quality part for your classic vehicle restoration.
Cowl vent weatherstrip
p/n: 70-0143-54
Gasket, cowl vent. Perfect copy of original, not a sponge substitute, top quality material.
Crankshaft Vibration Damper - Revulcanization Only
p/n: 30-0376-12
This Revulcanization Service Only is designed to restore the Crankshaft Vibration Damper to a like new original condition. This revulcanizing service is for the rubber cushion elements. Service requires your metal core.