Firewall Grommet
p/n: 30-0070-21
This Firewall Grommet is used to run instrument board cables through the firewall. The oval type with masked hole for six (6) wires or cables is the necessary replacement for correct restoration.
Gearshift Boot - Black
p/n: 20-0334-26
This reproduction Black Gearshift Boot is designed from the original part for an authentic fit, finish, and appearance.
Hood Corner Pad
p/n: 60-0118-42
Pad. hood corner, steel core as original, front and rear.Length: 1.5 inches.
Rear Bumper Arm Grommets
p/n: 20-2170-29
This Rear Bumper Arm Grommet pair is designed from the original part for an authentic fit, finish, and appearance.
Fuel Neck Grommet
p/n: 50-0067-39
Grommet, fuel filler neck. Oblong fully molded rubber. Two and one eighths inch (2-1/8") inch inside length by three and one half inch (3-1/2") outside diameter by three and three fourths inch (3-3/4") outside length.
Rigid Run Channels
p/n: 70-0347-58
This Rigid Run Channel pair is stainless beaded and mohair-lined to help eliminate window rattles and provide a smooth sliding surface for glass movement. Also works to protect the glass.
Cowl Vent Gasket
p/n: 30-0519-54
Gasket, cowl vent. Die cut sponge with smooth curves. Excellent reproduction designed to fit in gutter and not bind when closing.Length: 15.75 inches.
Engine Mount
p/n: 30-0292-11
This Engine Mount pair is used as the engine crank case link ball insulator. Correctly designed with careful attention to detail as original. Sold only in pairs.
Steering Column Floorplate
p/n: 50-0260-36
Retainer, front floor mat on steering column (also called steering column floorplate). Black rubber. For brown see our #50-0260-89.Width: 4.3125 inches.
Hood Bumper Set
p/n: 20-2187-42
This twenty-two (22) piece Hood Bumper set is designed from the original parts for superior fitment and function.
Side Mount Grommet
p/n: 40-0269-37
Grommet, spare wheel sidemount main support tube. Covers hole in fender, one per vehicle.Length: 4.875 inches.
Fuel tank support pad
p/n: 60-0026-41
Pad, fuel tank support and floorboard seal. Sponge rubber ring. Two (2) per car.
Flexible Run Channel - 6 Ft.
p/n: 70-1108-57
Channel, flexible window run, un-beaded. Cloth covered mohair-lined type. Available in 6ft lengths.
Clutch and Brake Pedal Pads - Bowtie Emblem
p/n: 60-0125-22
This reproduction Clutch and Brake Pedal Pad pair slips over the full perimeter of the pedal for a precise, factory fit. A perfect reproduction to replace worn original pedal pads. Manufactured in quality black rubber with Chevy bowtie in tread.
Cowl Vent Gasket
p/n: 14-0037-54
Gasket stock, cowl vent, high grade sponge of proper cross-section, (not molded into ring), approximately forty eight (48) inch strip per car.
Fuel Neck Grommet
p/n: 10-0120-41
Grommet, fuel filler neck. Fully molded rubber. Three and five eighths inch (3-5/8") outside diameter by two and five eighths inch (2-5/8") inside diameter by thirteen sixteenths inch (13/16") height.
Rumble Seat Step Pad
p/n: 60-0126-45
Pad, rumble seat step, on rear bumper bracket or fender. Rubber cover only, full slip-over type with bowtie emblem.
Rumble Seat Step Pad
p/n: 27-0005-44
Pad, rear bumper step, rubber only. Fits old metal core.Height: .8125 inches.
Trunk Hinge Mounting Pad
p/n: 40-0134-85
Pads, trunk hinge mounting. Three and one half (3-1/2) inch and five (5) inch long sections. Sold as four (4) piece set for two (2) hinges.
Beltline Weatherstrips
p/n: 40-0539-57
This Beltline Weatherstrip pair installs on the left and right doors to wipe the inside and outside of the windows when the glass is lowered. Flexible, pile lined, rubber covered, with a black bead. Available in 3ft pair.
Brake and Clutch Shank Seal
p/n: 40-0217-24
Draft cap for brake and clutch pedal.Length: 2.4375 inches. Width: 1.6875 inches.
Brake and clutch shank seal
p/n: 70-0156-23
Grommet, brake and clutch pedal shank at toe board. Flange retained, perfect copy.
Convertible Top - Resting Block
p/n: 20-2231-67
Pad, convertible top resting block. Used when top is down. One (1) required per vehicle.
Flexible Run Channel
p/n: 70-1239-58
This Flexible Run Channel provides a smooth sliding surface while helping to eliminate rattle and protect the glass. The run channel has the stainless beaded edge and is cloth covered and mohair lined with the flexible metal channel.
Taillight Mounting Pad
p/n: 40-0172-15
Pad, taillight bracket mounting. Right and left, plain pad without beading as original. Length: 5.3125 inches.
Door Bottom weatherstrip
p/n: 70-3140-73
Seal, lower door. Mounts to door scuff plates. Enough for 4 doors.
Trunk Weatherstrip
p/n: 20-2266-84
This Trunk Weatherstrip is designed from the original part for superior fitment and seal. The seal mounts around the full perimeter of the trunk directly to the body.
Vent division bar weatherstrip
p/n: 30-0461-56
Front vent window division post seal. Fully molded with metal core and attaching tabs.
Gearshift Boot
p/n: 40-0111-88
Boot, base of gearshift lever. Black rubber. For brown see our #40-0111-89. Made separately to fit most of our gearshift floorplates. Copied from original.
Vent Window Division Post Weatherstrips
p/n: 70-0791-56
This Front Vent Window Division Post Weatherstrip pair is designed from the original part for superior fitment and seal. These pieces mount on the vertical division post with tabs and seal as the vent glass closes against them. Fully molded with metal core.
Vent Window Division Post Weatherstrips
p/n: 60-0596-56
This Front Window Vent Division Post Weatherstrip pair is fully molded with metal core and attaching tabs.
Window Felt Beltline Weatherstrips
p/n: 70-0555-58
These Window Felt Beltline Weatherstrips are sold as a three (3) foot pair. The beltline is used for side windows inner and/or outer, front and/or rear doors. Available in a 3ft pair.
Vent Division Bar Weatherstrip
p/n: 70-0695-74
Division bar seal. Proper cross section rubber molded to original style metal with authentic attaching tabs.
Vent Window Division Bar Weatherstrips
p/n: 70-2094-56
This Front Vent Window Division Bar Weatherstrip pair is designed from the original part for superior fitment and seal. This piece mounts on the vertical division bar vent window glass closes against it. Fully molded with metal core and attaching tabs.
Brown Gearshift Boot
p/n: 50-0035-89
Boot, gearshift. Brown rubber. For black see our #50-0035-24.Color:brown Width: 2.8125 inches.
Sway Bar Bushing
p/n: 30-0285-33
Bushing, sway bar (stabilizer lateral tube). Two (2) used per car. Fully molded rubber. Two and three sixteenths inch (2 3/16") length by one and one half inch (1 1/2") outside diameter by five eighths inch (5/8") inside hole diameter.
Windshield filler
p/n: 30-0105-52
Filler, windshield division channel ends, upper and lower. Two (2) piece set.
Brake and Clutch Shank Seal
p/n: 30-0143-24
Boot, brake and clutch pedal shank at toe board.Length: 2.9375 inches.
Front Coil Spring Pad
p/n: 50-0476-35
Pad, front coil spring insulator, upper. Two (2) per car, five and one eighths (5-1/8) inch outside diameter. Height: .28125 inches.
Rear spring bushing
p/n: 60-0311-35
Bushing, rear spring front eye, inlox cartridge type as original.
Trunk Hinge Mounting Pad
p/n: 50-0106-87
Mounting pads, trunk hinge, four (4) piece set. Models with outside hinges.Length: 8.25 inches.
