License Plate Light Lens Gaskets
p/n: 70-0560-17
This License Plate Light Lens Gasket pair is designed from the original part for superior fitment and seal. This reproduction gasket fits between the License Plate Light Lens and the License Plate Light Housing or Bezel.
Brown Accelerator Pedal Pad
p/n: 70-0208-89
Pad, accelerator pedal. Brown rubber. For black see our #70-0208-40. Made to slip over old metal core after removing old rubber.
Brake and Clutch Pedal Pads - Brown
p/n: 40-0107-89
This reproduction Clutch and Brake Pedal Pad pair slips over the full perimeter of the brake pedal for a precise, factory fit. An oval style perfect reproduction to replace worn original pedal pads. Manufactured in Brown rubber.
Red Brake and Clutch Pedal Pad
p/n: 30-0188-89
Pads, brake and clutch pedal, slip over type. Black and red rubber. For black only see our #30-0188-22.Length: 3.875 inches. Width: 2.875 inches.
Windshield Gasket
p/n: 20-1605-50
This Windshield Gasket mounts around the full perimeter of the front glass and has the divider bar molded directly into it for a precise, factory fit. It also has the slot to accommodate the outer edge's decorative molding.
Convertible Top Arm Pad
p/n: 50-0310-67
Pad, folding post, lower, on bottom of post, held by two (2) screws. Brass core, right and left hand.
Rear Bumper Grommet
p/n: 40-0468-30
Grommets, rear bumper. Fully molded rubber, used on rear side brackets only.
Rear Axle Bumpers
p/n: 70-0210-32
This Rear Axle Bumper pair is a quality reproduction of the original factory part. These bottoming pads are dense rubber blocks that mount by bracket to the rear axle tube.
Stabilizer Bushing
p/n: 70-0627-33
Bushings, stabilizer bar, front. Fully molded rubber. One and three fourths inch (1 3/4") length by one and one half inch (1 1/2") width by three fourths inch (3/4") inside hole diameter by one and five eighths inch (1 5/8") height.
Convertible Top Arm Pad
p/n: 70-1217-67
Pad, top folding post. Fastens on lower end of post with two (2) screws. Metal core, close copy.
Roof Rail Filler
p/n: 50-0255-67
Filler, folding top side roof rail to front roof rail. Right and left with metal core as original.
Rigid Run Channels
p/n: 30-0023-57
This Rigid Run Channel pair for the division bar is un-beaded, steel core, plush lined, and cloth covered. Available as 28" pair.
Front Spring Bumpers
p/n: 60-0393-32
This Front Spring Bumper pair is a quality reproduction of the original factory part. These axle to frame bottoming rebound pads are dense rubber blocks that mount to the front axle.
Fender Skirt Edge Weatherstrip
p/n: 70-0154-45
This Fender Skirt Edge Weatherstrip pair is designed from the original part for superior fitment, finish, and seal. This weatherstrips fits between the rear wheel fender skirt and the rear fender quarter panel.
Side Window Beltline Scraper Weatherstrips
p/n: 60-0566-58
These inner and outer Side Window Beltline Scraper Weatherstrips slide into the groove on top of the door's window opening and wipes the glass when window is raised and lowered. Four (4) piece set.
Spring Shackle Bushing Set
p/n: 20-1581-33
This Spring Shackle Bushing Set is for the rear leaf springs. This set is an original steel stud type.
Fender Skirt Edge Weatherstrip
p/n: 70-0289-45
This Fender Skirt Edge Weatherstrip pair is designed from the original part for superior fitment, finish, and seal. This weatherstrips fits between the rear wheel fender skirt and the rear fender quarter panel.
Rear Spring Bumper
p/n: 60-0137-32
Bumper, rear spring. Fits original retainer.Width: 2.5625 inches.
Prop shaft retainer bushing
p/n: 70-2268-27
Retainer, intermediate bearing. All models with two piece driveshafts.
Front Bow Weatherstrip
p/n: 40-0418-65
This Front Bow Weatherstrip is designed from the original part for superior fitment and seal. Top quality extrusion cut five (5') feet long.
Brake and Clutch Pedal Pads
p/n: 30-0188-22
Pads, brake and clutch pedal, slip over type. Black rubber only. For black and red (semi-automatic clutch models) see our #30-0188-89.Length: 3.875 inches.
Sliding Quarter Window Seal
p/n: 60-0398-78
Weatherstrip, sliding quarter window. Mounted vertically in body where leading edge of sliding window fits when closed. Right & left rubber only.
Rear Bumper Grommet
p/n: 70-2231-29
Grommets, rear support arm. Fully molded with all original details.
Window Felt Beltline Weatherstrips
p/n: 20-0383-60
This is a Original equipment style side window horizontal weatherstrip set (also known as beltline weatherstrip). This four (4) piece anti-rattle set includes inner and outer window felt beltline weatherstrips for each door window.
Clutch and Brake Pedal Pads - Black
p/n: 40-0107-22
This reproduction Clutch and Brake Pedal Pad pair slips over the full perimeter of the brake pedal for a precise, factory fit. An oval style perfect reproduction to replace worn original pedal pads. Manufactured in Black rubber.
3" Firewall Grommet
p/n: 30-0110-42
This Firewall Grommet pair is used for the hood lock link through the firewall. Designed from the original part for superior fit and seal.
Taillight Lens Gasket
p/n: 40-0348-15
Gasket taillight lens. Relieved top and bottom as original, for better sealing.Length: 4.3125 inches. Width: 2.5 inches.
Body To Frame Mounting Pad Set
p/n: 20-1598-48
This twenty-five (25) piece Body To Frame Mounting Pad set is designed from the original parts for superior fitment and function. A complete set of rubber pads and biscuits to isolate the vehicle body from the vehicle frame. Installation instructions are included.
Body to Frame Webbing
p/n: 20-1599-48
This Body to Frame Webbing is designed from the original part for superior fitment and function. This webbing is used to shim the body to the frame. Also used as a noise reducer material. Webbing is two (2) inch wide, twenty-five (25) foot long roll.
Trunk Emblem Mounting Pad
p/n: 50-0114-17
Mounting pad, trunk ornament. Top quality material, finely detailed.Hole to hole this part measures 9.5 inches.Width: 13.875 inches.
Rear Window Gasket Set
p/n: 20-0398-81
This Rear Window Gasket Set is designed from the original part for superior fitment and seal. The seal mounts around the full perimeter of the back glass and has vulcanized, or bonded, ends which means no cutting or splicing is required for installation.
Swing-Out Windshield Weatherstrip
p/n: 40-0018-52
This Swing-Out Windshield Weatherstrip comes in an eleven (11) foot strip. The seal slides into the track (channel) attached to the glass that goes all the way around the windshield and creates a seal when the glass is pressed against the body of the vehicle.
Door Bumper
p/n: 70-0168-71
Bumper, door side. Square type held by four (4) screws, metal core as original.
Hood To Cowl Weatherstrip
p/n: 60-0091-42
This Hood To Cowl Weatherstrip pair is molded with all original details. One (1) pair required per car. Length: 11 inches.
Fender Skirt Edge Weatherstrip
p/n: 20-0111-44
This Fender Skirt Edge Weatherstrip pair is designed from the original part for superior fitment, finish and sealing function. Two five (5) foot strips that fit between the rear wheel fender skirt and rear quarter panel.
Engine Mount Pad
p/n: 70-2577-11
This Engine Mount Pad pair is used as a lower support cushion. Correct design and rubber compound. Sold as a pair.
Radiator Mounting Pad
p/n: 30-0309-31
Grommet, several usages. Radiator core cradle tie rod to frame or rear stabilizer pad to link to where the leaf springs are bolted. Fully molded rubber. 2nd type with chamfered edge. Comes as a (4) piece set.
Division Bar Grommet
p/n: 70-0483-62
These Division Bar Grommets are fully molded for the rear door vent divider post (wind deflector). Four (4) piece set.
Front Suspension Rubber Bumper
p/n: 60-0103-32
Front Suspension Rubber Bumper for the front suspension lower control arm (attaches to lower arm spring mount). Steel core, with original size bolt. Width: 1.625 inches.
Clutch or Brake Pedal Pad - Brown
p/n: 70-0176-89
This reproduction Clutch or Brake Pedal Pad slips over the full perimeter of the pedal for a precise, factory fit. A perfect reproduction to replace worn original pedal pads. Manufactured in quality brown rubber.
Front Stabilizer Bushing
p/n: 70-0193-33
Bushings, front stabilizer bar. Fully molded rubber. One and five eighths inch (1 5/8") length by one and seven sixteenths inch (1 7/16') width by three fourths inch (3/4") inside hole diameter by one and eleven sixteenths inch (1 11/16") height.
Fresh air gasket
p/n: 70-1768-31
Seal, fresh air adaptor door. Part of assembly #903964. For vehicles with accessory air control systems.
Spring Shackle Bushing Set
p/n: 20-1580-33
This Spring Shackle Bushing Set is for the front leaf springs. This set is an original steel stud type.
Brake and Clutch Pedal Pads - Black
p/n: 40-0121-22
This reproduction Clutch and Brake Pedal Pad pair slips over the full perimeter of the brake pedal for a precise, factory fit. An oval style perfect reproduction to replace worn original pedal pads. Manufactured in Black rubber. For Brown see our 40-0121-89.
Taillight Mounting Pad
p/n: 27-0069-15
Pad, taillight mounting pad to body. Fully molded with original details. Length: 6.375 inches.
Stabilizer Bar End Link Set
p/n: 70-0567-34
Twenty-two (22) piece Stabilizer Bar End Link set for both sides of one (1) vehicle, fits front or rear bar. Order two (2) sets for vehicles with front and rear stabilizer bars. Hex head bolt. 5/16"-24NF x 7-5/8" long. Includes metal sleeves, cup washers and rubber grommets.
Clutch and Brake Pedal Pads - BROWN
p/n: 25-0024-89
This reproduction Clutch and Brake Pedal Pad pair slips over the full perimeter of the brake pedal for a precise, factory fit. A reproduction with authentic type ribbing, to replace worn original pedal pads. Manufactured in Brown rubber.
Fuel Neck Grommet
p/n: 18-0020-41
Grommet, fuel filler neck. Fully molded rubber with retaining flange.
Fuel Neck Grommet
p/n: 70-0599-39
Grommet, fuel filler neck, through rear fender splash panel. Fully molded rubber. Four and five eighths inch (4 5/8") outside diameter by two and three sixteenths inch (2 3/16") inside hole diameter.
Parking lamp lens gasket
p/n: 70-3526-16
Gasket, front parking and directional lamp. Fully molded rubber. Includes both right and left sides.
Rear Gravel Deflector to Bumper Face Bar
p/n: 70-0462-45
This Rear Gravel Deflector to Bumper Face Bar staples to the gravel deflector. The seal is die cut from dense rubber. Sold as a six (6) foot strip.
Front Stabilizer Bushing
p/n: 50-0170-34
Bushings, front stabilizer bar mounting. Fits original bracket. Fully molded rubber. One and five eighths inch (1 5/8") length by one and three eighths inch (1 3/8") outside diameter by eleven sixteenths inch (11/16") inside hole diameter.
Taillight Mounting Pad
p/n: 60-0008-15
Mounting pads, taillight. Length: 6.50 inches. Width: 2.6875 inches.
Rear Window Gasket Set
p/n: 60-0082-83
This Rear Window Gasket Set contains the rear window gasket itself and the locking strip. Both strips comes in a ninety inch (90") piece and mount around the full perimeter of the back glass. The ends may require trimming and bonding for installation.
Door weatherstrip
p/n: 20-1644-73
Weatherstrips, open car door hinge. Door seals molded to fit hinge area.
Front Spring Rubber Bumpers
p/n: 70-0329-32
This Front Spring Rubber Bumper Pair fits to the upper control arms on frame. Manufactured to OEM specifications to install for an authentic fit, finish and function.
Clutch and Brake Pedal Pads
p/n: 60-0068-22
This reproduction Clutch and Brake Pedal Pad pair slips over the full perimeter of the pedal for a precise, factory fit. An oval style perfect reproduction to replace worn or damaged original pedal pads.
Parking Light Lens Gasket
p/n: 70-2275-16
Gasket, parking light lens. Fully molded, with proper edge lip and shape. One (1) pair needed per car.Length: 4.6875 inches. Width: 2.0625 inches.
Taillight Lens Gasket
p/n: 70-3524-15
Gasket, taillight lens. Fully molded rubber. Includes both right and left sides.
Brown Accelerator Pedal Pad
p/n: 50-0160-89
Pad, accelerator pedal. Brown rubber. For black see our #50-0160-40. Slip-over type for old core, perfect copy. Color: brown Length: 9.0 inches.
Accelerator Pedal Pad
p/n: 70-0208-40
Pad, accelerator pedal. Black rubber. For brown see our #70-0208-89. Made to slip over old metal core after removing old rubber. Length: 8.25 inches.
Clutch and Brake Pedal Pads - BLACK
p/n: 25-0024-22
This reproduction Clutch and Brake Pedal Pad pair slips over the full perimeter of the brake pedal for a precise, factory fit. A reproduction with authentic type ribbing, to replace worn original pedal pads. Manufactured in Black rubber.
License Light Mounting Pad
p/n: 70-0559-17
Pad, license light bracket or base mounting. Two (2) per car.
Brake Master Cylinder Filler Access Hole Cover
p/n: 60-0016-24
This Master Cylinder Access Hole Cover is designed from the original part for superior fitment and seal. Secures the Brake Master Cylinder Filler and Inspection Access Hole in the vehicle.
Clutch Equalizer Bushing and Seals
p/n: 70-2029-24
This Clutch Equalizer Bushing and Seal set is designed from the original part for superior fitment and operation. The set includes a metal sleeved rubber bushing and two (2) molded rubber seals for each end of equalizer shaft.
1935-1974 Cadillac Factory Parts Manual, CD
p/n: 07-1346-07
This GM Licensed Detroit Iron CD provides the most comprehensive set of digital Cadillac Factory parts manuals. The factory manuals on this CD were professionally scanned from the original service and parts manuals.
Overload Spring Arm Bumpers
p/n: 70-2301-32
A reproduction Overload Spring Arm Bumper pair manufactured to OEM specifications. Fully molded quality rubber bumpers that installs in the truck's overload spring arms.
Flexible Run Channel - 60 Inch
p/n: 20-1619-58
Channel, side window glass, vertical run. Flexible, felt lined, rubber covered channel. Available 60" lengths.
Door - Gravel Shield - Running Board Weatherstrip
p/n: 60-0054-73
This Door - Gravel Shield - Running Board Weatherstrip is a anti-squeak bulb type extrusion with fitment for General Motors vehicles. A twelve (12) foot strip made of high-quality EPDM dense rubber and designed from original parts for superior fitment, finish and function.
Front Fender Seals
p/n: 60-0522-45
Seal, front fender baffle, right and left. One (1) pair per car. Length: 5-1/4" inches.
Front Stabilizer Bushing
p/n: 30-0123-33
Bushings, front stabilizer mounting bracket. Fully molded rubber.