Shock and Sway Bar Grommet
p/n: 30-0193-33
Grommet, rear shock arm link (lower end), or rear sway bar link lower end. Shock arms used four (4) per car. If needed, sway bar used two (2) per car. Fully molded rubber.
Door Bumper
p/n: 17-0039-71
Bumper, round door side. An auxiliary door side bumper on door jamb pad.
Wheel cover cushion
p/n: 70-1024-38
Cushion, wheel disk. A fully molded alternative to our #70-0094-38.
Brake Master Cylinder Push Rod Boot
p/n: 60-0180-24
This Brake Master Cylinder Push Rod Boot is made from high-quality Nitrile rubber for a precise, factory like fit for your classic vehicle. Manufactured to OEM specifications to install for an authentic fit and finish.
Steering Column Cushion
p/n: 40-0259-36
Pad, steering post bracket. One (1) per car. Cushions steering post clamp to instrument panel.Length: 3.50 inches.
Brown Steering Column Cushion
p/n: 60-0012-89
Grommet, steering column to cowl, for U-bolt clamp. Brown rubber. For black see our #60-0012-36.Color:brown Height: 1.25 inches.
Door Bumper
p/n: 30-0128-71
Pad, door jamb (Atwood type), one and five eighths (1-5/8) inch long.Width: 1.5625 inches. Height: 1.375 inches.
Starter Pedal Button Cover
p/n: 60-0166-21
This Starter Button Pedal Cover is designed from the original part for an authentic fit, finish, and appearance. Rubber slip over type for old metal. Two (2") inch outside diameter.
Firewall Grommet
p/n: 50-0396-20
This Firewall Grommet is used to run the wiring harness and other various wires through the firewall. Designed from the original part for superior fit and seal.
Vacuum Cylinder Seal
p/n: 30-0203-24
Seals, actuating valve rod, brake and clutch vacuum cylinder.Width: .875 inches.
Door Alignment Pad
p/n: 70-1821-71
Wedge pads, door aligning.Length: 1.125 inches. Width: .5 inches. Height: .875 inches.
Firewall Grommet
p/n: 60-0010-45
This Firewall Grommet is the oblong four (4) hole style. The grommet fits the steel retainer for the throttle and choke cables, and the oil and temperature lines.
Door Bumper
p/n: 17-0038-70
Wedge cushion, door dovetail. This is the rubber block which goes behind the dovetail receiving bumper or shoe.
Headlight Mounting Pad
p/n: 60-0557-14
Pad, headlight bracket to radiator shell. Round, with proper type weatherlip as original. Two (2) required per vehicle.
Taillight Mounting Pad
p/n: 60-0116-15
Pad, taillight bracket to fender. Four (4) inches long. Compare with our #60-0172-15 and #60-0545-15. Length: 4.0 inches.
Fender Welting
p/n: 20-1591-44
This black Fender Welting is designed from the original part for superior fitment and seal. This welting material fits between the fenders and the vehicle body. Eight (8) foot length.
Rear Window Gasket
p/n: 20-0394-81
This Rear Window Gasket is made just like the original and mounts around the full perimeter of the back glass. The ends may require trimming and bonding for installation.
Door Weatherstrip
p/n: 60-0047-73
Weatherstrip, lower door. Fastens to cab threshold. Two strips thirty six (36) inch long each.Length: 36.0 inches. Width: .4375 inches.
Rear Spring Pad
p/n: 70-0191-32
Pad, rear spring insulator for two (2) inch wide springs. (see our number 70-0245-32 for two and one fourth (2-1/4) inch springs). Cloth reinforced. Four (4) per vehicle.
Wiper Transmission Gasket
p/n: 50-0081-53
Gasket, windshield wiper transmission.Width: 2.5625 inches. Height: .8125 inches.
Shock Absorber Arm Bushing
p/n: 30-0192-32
Bushing, shock absorber arm. Restore proper shock action.Height: 1.375 inches.
1-7/16" Firewall Grommet
p/n: 40-0204-21
This Firewall Grommet is used to run the wiring harness through the firewall. Designed from the original part for superior fit and seal.
Door handle gasket
p/n: 40-0191-70
Pad, outside door handle escutcheon. Compare with our #40-0207-70.
Windshield Division Bar Gasket
p/n: 70-0059-51
Gasket, set, inner and outer, for divided windshield center post. Two (2) piece set.
Gearshift Boot - Brown
p/n: 20-2166-26
This Gearshift Boot is designed from the original part for superior fitment and seal. This boot fits over the gearshift tower to make a weathertight connection for the transmission gearshift rod as it passes up through the vehicle floorboard.
Starter Pedal Pad
p/n: 25-0049-89
Pad, starter pedal. Original pattern, brown rubber, exact copy.Height: .50 inches.
Shock Absorber Link Bushings
p/n: 30-0226-33
A Rear Shock Absorber Upper Link Bushing pair designed from the original part for superior fitment and function. Rubber sleeve construction like original.
Firewall Grommet
p/n: 40-0223-21
This Firewall Grommet can be used for a variety of applications since the grommet is plain (no holes). Designed from the original part for superior fit and seal.
Rear Spring Pad
p/n: 70-0245-32
Pad, rear spring insulator for two and one fourth (2-1/4) inch wide springs. (see our number 70-0191-32 for two (2) inch springs). Four (4) per vehicle.
Rear Window Gasket
p/n: 30-0086-83
This Rear Window Gasket comes in a seven (7) foot strip and mounts around the full perimeter of the back glass. The ends may require trimming and bonding for installation.
Taillight Mounting Pad
p/n: 60-0364-15
Pad, taillight mounting to rear fender. Length: 1.0625 inches.
Clutch, Brake Pedal or Rumble Seat Pads
p/n: 20-0325-22
This reproduction Pad pair easily screws on the clutch and brake pedal arms for a precise, factory fit. Pads with pyramid design like original. Used as clutch and brake pedal pads for all models. Used as a rumble seat step pad for cars so equipped.
Horn trumpet grommet
p/n: 70-0302-21
Grommets, horn projector. For under hood horn brackets. Two (2) per car.
Horn Trumpet Grommet
p/n: 70-1200-21
Grommets, horn trumpet mounting. One (1) inch inside diameter, 1-3/8 inch outside diameter, 9/16 inch high.
Starter Button
p/n: 27-0048-21
Button, starter pedal rod. All rubber, made to work directly onto pedal rod three eighths (3/8) inch hole.
Trunk Weatherstrip
p/n: 70-0798-84
This Trunk Weatherstrip is designed from the original part for superior fitment and seal. The seal mounts around the full perimeter of the trunk directly to the body.
Cowl Vent Gasket
p/n: 60-0087-54
Gasket, cowl vent, lip type. Sponge rubber, for three and seven eighths (3-7/8) inch by fifteen (15) inch cowl vent.Length: 15.0 inches. Width: 3.
Clutch and Brake Pedal Pads - Black
p/n: 50-0054-22
This reproduction Clutch and Brake Pedal Pad pair slips over the full perimeter of the pedal for a precise, factory fit. A perfect reproduction to replace worn original pedal pads. Manufactured in quality black rubber.
Firewall Grommet
p/n: 40-0221-21
This Firewall Grommet is used to run the speedometer cable, oil tube, and the temperature tube through the firewall. The three (3) holes measure 5/16", 1/4", 3/16".
Door Weatherstrip
p/n: 20-0390-72
This Door Weatherstrip is the primary door to body weatherstrip. Includes enough to do front, top and backside of one door. Order two (2) for both doors.
Starter Button Cover
p/n: 60-0322-21
This Starter Button Cover is designed from the original part for an authentic fit, finish, and appearance. A push on replacement to rod. Two (2") inch outside diameter.
Firewall Grommet
p/n: 50-0272-20
This Firewall Grommet is used to run the water temperature indicator pipe through the dash. Designed from the original part for superior fit and seal.
Taillight Lens Gasket
p/n: 30-0336-15
Gaskets, taillight door lens. For cars without center license light. Two (2) strips eleven and one half (11-1/2) inches long each.Length: 11.5 inches.
Firewall Grommet
p/n: 70-1203-20
This Firewall Grommet is used to run various electrical and dash gauge wires through the firewall. Also see our 32-1201-20 and 32-0225-20.
Brake and Clutch Shank Seal
p/n: 40-0016-24
Seal, brake and clutch pedal shank to floorboard (draft excluder).Length: 2.4375 inches. Width: 1.875 inches.
Firewall Grommet
p/n: 40-0222-21
This Firewall Grommet is used to run the throttle cable and wiper vacuum line through the firewall as well as a drain hole for the cowl vent. The holes in the three (3) hole design measure: 9/16", 3/8", and 1/4".
Side mount grommet
p/n: 40-0534-37
Grommets, sidemount. Please see sketches and specify #40-0533-37 or #40-0534-37 when ordering.
Side Mount Grommet
p/n: 40-0140-37
Grommet, sidemount carrier brace to fender. One and five sixteenths (1-15/16) inch outside diameter by one half (1/2) inch inside diameter.
Accelerator Rod Seal
p/n: 40-0205-88
This Accelerator Rod Seal is used as an accelerator rod through the toeboard. Molded from a high-quality EPDM dense rubber.
Starter Pedal Bellows
p/n: 60-0487-21
Bellows, starter pedal shaft-to-floorboard. One and three fourths (1-3/4) inch by two and one fourth (2-1/4) inch.Length: 2.25 inches. Width: 1.75 inches.
Brake and Clutch Shank Seal
p/n: 50-0066-24
Grommet, brake and clutch pedal floor seal.Width: 1.8125 inches. Height: 2.375 inches.
5" Wide Bow Drill Cloth Tape
p/n: 70-1175-65
This Bow Drill Cloth Tape is used for covering convertible side window weatherstrip. Black in color and available in a five (5) foot roll.
Rumble Seat Lid Corner Pad
p/n: 70-0048-87
Pads, rumble seat lid corners original style, rounded triangular shape.Width: 1.25 inches.
Engine Mount
p/n: 20-1980-11
This Engine Mount is designed from the original part for superior fitment and function. The engine mount works to isolate dampen engine and chassis vibrations.
Side Mount Cover Pad
p/n: 70-0077-37
Pads, channel type, for sidemount covers. Eight (8) piece set.Width: .25 inches. Height: .6875 inches.
Rumble Seat Lid Corner Pad
p/n: 70-0120-87
Pad, rumble seat lid corner, Compare with our #60-0191-87. Length: .75 inches.
Gearshift Boot
p/n: 50-0035-24
Boot, gearshift. Black rubber. For brown see our #50-0035-89.Width: 2.8125 inches.
Fender Welting
p/n: 20-1590-44
This black Fender Welting is designed from the original part for superior fitment and seal. This welting material fits between the fenders and the vehicle body. Thirty (30) foot roll.
Flexible Run Channel - 30 Inch Pair
p/n: 40-0309-57
Channel, side window glass, vertical run. Flexible, felt lined, rubber covered channel. Available in 30" pair.
Taillight Mounting Pad
p/n: 60-0172-15
Pad, taillight bracket mounting. Five and one half (5-1/2) inches long. Compare with our #60-0116-15. Length: 5.50 inches.
Headlight Grommet
p/n: 50-0237-14
Grommet, headlight wiring from headlight bulb through mounting brace.Height: 1.3125 inches.
Shock Absorber Bushing
p/n: 30-0024-33
Bushings, rear shock link assembly. Designed to act like sleeve inside link arm.Height: .9375 inches.
Fuel Filler Neck Grommet
p/n: 60-0022-41
This Fuel Filler Neck Grommet is fully molded rubber and slightly angled. Three and eleven sixteenths inch (3-11/16") outside diameter by two and three sixteenths inch (2-3/16") top hole diameter by two and five eighths inch (2-5/8") bottom hole diameter.
Rear Window Division Bar Seal
p/n: 40-0285-77
Gasket, back window division bar. Closed body styles with split back window.Length: 9.25 inches. Width: 1.125 inches.
Brake and Clutch Shank Seal
p/n: 30-0055-24
Seals, brake and clutch pedal shanks, against underside of floorboard.Length: 2.5625 inches. Width: 1.75 inches.
Convertible Post Bumper
p/n: 30-0409-67
Bumper, convertible top side roof rail, center. Two (2) per car.
Radio Antenna End Loop
p/n: 70-0105-21
End loop, radio antenna. Cord reinforced rubber with metal grommet. Mounted on running board on some models.
Brake and Clutch Shank Seal
p/n: 40-0175-24
Seal, brake and clutch pedal shank to floorboard. One and one half (1-1/2) inch by two and one eighth (2-1/8) inch by three fourths (3/4) inch thick.
Rear Engine Mount
p/n: 70-0648-11
This Rear Engine Mount is used as an upper and lower support bracket at the transmission. Made from high-quality EPDM rubber for a precise, factory like fit.
Cowl vent weatherstrip
p/n: 70-0143-54
Gasket, cowl vent. Perfect copy of original, not a sponge substitute, top quality material.
Rumble Seat Step Mounting Pad
p/n: 25-0019-44
Mounting pad for our #25-0018-44 fender step. Length: 7.375 inches.
Fuel Neck Grommet
p/n: 60-0336-41
Grommet, fuel filler neck. Fully molded rubber. Three and fifteen sixteenths inch (3-15/16") outside diameter by two and one sixteenth inch (2-1/6") top hole diameter by two and three sixteenths inch (2-3/16") bottom hole diameter.
Headlight Mounting Pad
p/n: 60-0558-14
Pad, headlight bracket at fender. See also our #60-0178-14. Two and one eighth (2-1/8) inch by three and seven sixteenths (3-7/16) inch.Length: 3.
Firewall Grommet
p/n: 70-0223-20
This Firewall Grommet is used on the lower end of the elbow from the firewall to the voltage regulator. Designed from the original part for superior fit and seal.
Trunk Weatherstrip
p/n: 20-2126-84
This Trunk Weatherstrip is designed from the original part for superior fitment and seal. The seal mounts around the full perimeter of the trunk directly to the body.
Brake and clutch pedal bumper
p/n: 30-0380-20
Bumper, inclined toe board pedal hole, carried on toe board to meet our #30-0055-24 pedal. dust cover.
Trunk Lid Clamp Mounting Pad
p/n: 30-0182-87
Pads, trunk lid hasp (clamp) mounting. Fine beaded edge, perfect copy. These are not hinge pads. Four (4) piece set.Length: 4.0 inches. Width: 1.0 inches.