Flexible Run Channel - 5ft
p/n: 70-1107-57
Cloth covered mohair-lined type. For sides and top of side windows. Available in 5ft lengths.
Brake and clutch shank seal
p/n: 60-0019-24
Seal, brake and clutch pedal shank to floorboard. Single bellows rubber cup, seals air drafts around pedals.
Rear Leaf Spring Bushings
p/n: 70-0663-32
This Rear Leaf Spring Bushing pair is designed from the original part for superior fitment and function. Busing are for the rear leaf spring front or rear spring eyes.
Hood Bumper
p/n: 30-0080-42
Bumper, inner hood rest. Good copy and material. One (1) pair required per car.Length: 1.50 inches. Width: .875 inches.
Wiring Grommet
p/n: 70-0709-21
Grommet, horn wire exit from horn motor cover. Eleven thirty seconds (11/32) inch inside diameter. Two (2) per car.
Fender Welting with 3/16 Bead - 25ft
p/n: 70-1099-44
A superior quality Fender Welting material constructed of reinforced black vinyl over a vinyl core. Typically used for attaching two (2) fenders to body. Sold in a 25 foot roll.
Rumble Seat Lid Bumper Pad
p/n: 30-0275-44
Bumpers, rumble seat stop bracket. Self-retaining type as original.Length: 1.1875 inches. Width: .75 inches. Height: .375 inches.
Rumble Seat Step Mounting Pad
p/n: 30-0181-44
Pad, rumble seat step bracket to fender. Four and one fourth (4-1/4) inch long.Length: 4.375 inches.
Cowl Vent Gasket
p/n: 30-0172-54
Gasket, cowl vent. Top quality sponge of correct section, cut to sufficient length for circumference of vent cover.
Accelerator Rod Seal
p/n: 60-0136-41
Grommet, accelerator rod through toe board. Brass core and center bushing as original.
Clutch and Brake Pedal Pads - Bowtie Emblem
p/n: 60-0043-22
This reproduction Clutch and Brake Pedal Pad pair slips over the full perimeter of the pedal for a precise, factory fit. A perfect reproduction to replace worn original pedal pads. Manufactured in quality black rubber. Excellent detail with bowtie emblem like original.
Headlight Mounting Pad
p/n: 60-0115-14
Pad, headlight support bracket. Two and one half (2-1/2) inch by six and one fourth (6-1/4) inch.Length: 6.25 inches. Width: 2.5 inches.
Window Felt Beltline Weatherstrips - 3ft Pair
p/n: 30-0244-57
This side window Window Felt Beltline Weatherstrip pair can be used as inner and/or outer. The weatherstrip is flexible, pile lined, rubber covered, with black bead. Available in 3ft pairs.
Rumble Seat Step Mounting Pad
p/n: 70-0043-44
Pad, rumble seat step mounting for fender, double beaded edge per original. Width: 4.375 inches.
Rumble Seat Step Mounting Pad
p/n: 30-0272-44
Gasket, rumble seat step. For left hand drive upper. Length: 5.0 inches.
Body Mounting Pad
p/n: 60-0412-48
Body bumpers, rear, at body hold-down bolt. Fully molded rubber. Comes as a pair of two (2). One and three fourths inch (1 3/4") outside length by one and one fourth inch (1 1/4") diameter by three eighths inch (3/8") inside hole diameter.
Windshield Division Bar Inner Gasket
p/n: 40-0284-52
This Windshield Division Bar Inner Gasket is designed from the original part for superior fitment and seal. This top quality EPDM rubber inner gasket fits to the inside of the windshield.
Chrome Fender Welting - 25ft
p/n: 70-1101-44
Welting, fender, bright chrome vinyl, three sixteenths (3/16) inch bead, one and one half (1-1/2) inch width. Superior quality. Twenty five (25) foot roll. Typically used to attach two (2) fenders to body. For fifty (50) foot roll see our #70-1102-44.
Fender Welting 1/4" Bead - 25ft
p/n: 70-1097-44
Welting, fender. Superior quality, proper construction of reinforced vinyl over vinyl core, one and three eighths (1-3/8) inch wide, black only. One fourth (1/4) inch bead, twenty-five (25) foot roll. Typically used to attach two (2) fenders to body.
Trunk or Rumble Seat Weatherstrip Set
p/n: 20-2127-84
This Trunk or Rumble Seat Weatherstrip Set is designed from the original parts for superior fitment and seal. The set includes the strip that mounts to the body and the strip that mounts to the lid.
Door Hinge Weatherstrips - Front of Door
p/n: 20-2112-73
This Door Hinge Weatherstrips pair is designed from the original parts for superior fitment and seal. Molded to fit around hinges at leading edge of front doors. For right and left doors.
Windshield Frame Weatherstrip
p/n: 20-2042-52
This Windshield Frame To Body Seal is made from the original design with quality materials for a precise, factory fit. This part installs around the perimeter of the windshield frame.
Accelerator Pedal Pad
p/n: 60-0097-40
Pad, accelerator pedal. Slip-over type for original core. Length: 9.125 inches.
Flexible Run Channel
p/n: 70-1238-58
Cloth covered, mohair lined flexible metal channel for sides and top of door windows.
Clutch and Brake Pedal Pads - Brown
p/n: 50-0054-89
This reproduction Clutch and Brake Pedal Pad pair slips over the full perimeter of the pedal for a precise, factory fit. A perfect reproduction to replace worn original pedal pads. Manufactured in quality brown rubber.
Rear spring bushing
p/n: 60-0311-35
Bushing, rear spring front eye, inlox cartridge type as original.
Brake and Clutch Shank Seal
p/n: 30-0143-24
Boot, brake and clutch pedal shank at toe board.Length: 2.9375 inches.
Brown Gearshift Boot
p/n: 50-0035-89
Boot, gearshift. Brown rubber. For black see our #50-0035-24.Color:brown Width: 2.8125 inches.
Fuel Neck Grommet
p/n: 60-0543-41
Seal, gas tank filler tube through floor pan, to inside of body. Made of soft flexible durometer rubber. Four and seven sixteenths inch (4-7/16") outside width by five and five eights inch (5-5/8") outside length.
Running Board or Inner Fender Splash Filler
p/n: 60-0288-45
This eight (8) foot Splash Filler strip is used for the running board apron to body or fender splash panels anti-rattle filler. This filler strip is top-quality EPDM sponge rubber to accept rivets or retaining screws.
Convertible Top - Rest Block
p/n: 50-0318-67
Rest block, convertible top. Two (2) required per car. Fits into dovetail retainer. Length: 1.375 inches. Width: 1.125 inches.
Vent division bar weatherstrip
p/n: 70-1461-56
Front vent window division post seal. Fully molded with metal core and attaching tabs.
Rumble Seat Step Mounting Pad
p/n: 30-0271-44
Gasket, rumble seat step center. Length: 5.875 inches.
Taillight Mounting Pad
p/n: 40-0206-15
Pad, taillight bracket to fender. This is plain style without lip. Two and five sixteenths (2-5/16) inch by five and one eighth (5-1/8) inch. Length: 5.
Taillight Mounting Pad
p/n: 40-0228-15
Mounting pad, tail and signal light. Length: 7.3125 inches. Width: 3.6875 inches.
Vent Division Bar Weatherstrip
p/n: 60-0509-56
This Vent Division Bar Weatherstrip is fully molded with metal core and attaching tabs. Sold as a pair for the drivers (LH) and passenger (RH) doors.
Cowl Vent Weatherstrip
p/n: 70-0224-54
Weatherstrip, cowl vent. Original solid rubber configuration, not a sponge substitute. A top quality part for your classic vehicle restoration.
License Light Mounting Pad
p/n: 40-0227-17
This License Light Mounting Pad is die cut from a dense rubber for a direct fit.
Window Felt Beltline Weatherstrips
p/n: 70-0555-58
These Window Felt Beltline Weatherstrips are sold as a three (3) foot pair. The beltline is used for side windows inner and/or outer, front and/or rear doors. Available in a 3ft pair.
Gearshift Boot
p/n: 40-0111-88
Boot, base of gearshift lever. Black rubber. For brown see our #40-0111-89. Made separately to fit most of our gearshift floorplates. Copied from original.
Swing-Out Windshield Weatherstrip
p/n: 20-3174-50
This Swing-Out Windshield Weatherstrip is designed from the original part. The weatherstrip mounts into the metal channel attached to the glass and creates a seal when the glass is pressed against the body of the vehicle.
Headlight Mounting Pad
p/n: 60-0178-14
Pads, headlight bracket mounting. Two (2) inch by three and five eighths (3-5/8) inch overall.Length: 3.625 inches. Width: 2.0 inches.
Vent division bar weatherstrip
p/n: 30-0461-56
Front vent window division post seal. Fully molded with metal core and attaching tabs.
Door Bottom weatherstrip
p/n: 70-3140-73
Seal, lower door. Mounts to door scuff plates. Enough for 4 doors.
Engine Mount Pad
p/n: 11-0026-11
This Engine Mount Pad is designed to original pattern with superior workmanship. Made from high-quality EPDM rubber for a precise, factory like fit. Two (2) required per car.
Flexible Run Channel
p/n: 70-1239-58
This Flexible Run Channel provides a smooth sliding surface while helping to eliminate rattle and protect the glass. The run channel has the stainless beaded edge and is cloth covered and mohair lined with the flexible metal channel.
Beltline Weatherstrips
p/n: 40-0539-57
This Beltline Weatherstrip pair installs on the left and right doors to wipe the inside and outside of the windows when the glass is lowered. Flexible, pile lined, rubber covered, with a black bead. Available in 3ft pair.
Brake and Clutch Shank Seal
p/n: 40-0217-24
Draft cap for brake and clutch pedal.Length: 2.4375 inches. Width: 1.6875 inches.
Fuel Neck Grommet
p/n: 10-0120-41
Grommet, fuel filler neck. Fully molded rubber. Three and five eighths inch (3-5/8") outside diameter by two and five eighths inch (2-5/8") inside diameter by thirteen sixteenths inch (13/16") height.
Hood to Cowl Fabric Lacing
p/n: 20-2022-43
This Hood To Cowl Fabric Lacing is designed from the original part for superior fitment and seal. This lacing attaches to the cowl at the rear of the engine bay to fit between the hood and cowl with hood closure.
Rumble Seat Step Pad
p/n: 27-0005-44
Pad, rear bumper step, rubber only. Fits old metal core.Height: .8125 inches.
Cowl Vent Gasket
p/n: 14-0037-54
Gasket stock, cowl vent, high grade sponge of proper cross-section, (not molded into ring), approximately forty eight (48) inch strip per car.
Cowl Vent Gasket
p/n: 20-2049-54
This Cowl Vent Gasket is designed from the original part for superior fitment and seal. This gasket works to seal the cowl vent when closed into the cowl body. Made from top quality rubber to ensure durability and proper seal.
Flexible Run Channel - 6 Ft.
p/n: 70-1108-57
Channel, flexible window run, un-beaded. Cloth covered mohair-lined type. Available in 6ft lengths.
Hood Corner Pad Set
p/n: 20-2017-42
This twenty-six (26) piece Hood Corner Pad set is designed from the original parts for superior fitment and function. The set includes grille area and cowl bumpers as required.
Steering Column Grommet
p/n: 40-0078-36
Grommet, steering column to toe board. Black rubber. For brown see our #40-0078-89.Length: 5.375 inches.
Side Mount Grommet
p/n: 40-0269-37
Grommet, spare wheel sidemount main support tube. Covers hole in fender, one per vehicle.Length: 4.875 inches.
Cowl Vent Gasket
p/n: 30-0179-54
Gasket, cowl vent, original labyrinth type, not sponge.Length: 14.75 inches. Width: 5.50 inches.
Engine Mount
p/n: 30-0292-11
This Engine Mount pair is used as the engine crank case link ball insulator. Correctly designed with careful attention to detail as original. Sold only in pairs.
2-3/8" Firewall Grommet
p/n: 30-0056-21
This Firewall Grommet is made to run the ignition cable and thermometer tube through the firewall. Designed from the original part for superior fit and seal.
Rigid Run Channels
p/n: 70-0347-58
This Rigid Run Channel pair is stainless beaded and mohair-lined to help eliminate window rattles and provide a smooth sliding surface for glass movement. Also works to protect the glass.
Fuel Neck Grommet
p/n: 70-0050-39
Grommet, fuel filler neck. Fully duplicates original with large retaining flange. Flexible, molded rubber. Four and one eighth inch (4-1/8") outside diameter by two and three sixteenth inch (2-3/16") inside hole diameter.
Brake Cable Anti-Rub Cover
p/n: 60-0443-24
Sleeve, rear brake cable anti-rub. Six (6) piece set. One half (1/2) inch inside diameter, seven eighth (7/8) inch outside diameter.
Accelerator Pedal Pad
p/n: 40-0113-40
Pad, accelerator pedal. Black rubber. Slipover type. Exact pattern, perfect copy in all details.
Steering Column Grommet
p/n: 40-0144-36
Grommet, steering column to toe board. Black rubber. For brown see our #40-0144-89. Two and three fourths (2-3/4) inch by seven and one half (7-1/2) inch.
Accelerator Pedal Pad
p/n: 50-0037-40
Pad, accelerator pedal. Slip-over type with heavy retainer lip to fit over original pedal after stripping old rubber off. Length: 8.625 inches.
Gearshift Boot - Black
p/n: 20-0334-26
This reproduction Black Gearshift Boot is designed from the original part for an authentic fit, finish, and appearance.
Cowl Vent Gasket
p/n: 40-0225-54
This Cowl Vent Gasket is designed from the original part for superior fitment and seal. Installs for a like factory fit and finish.
Fuel Neck Grommet
p/n: 40-0043-39
Grommet, fuel filler neck. Fully molded rubber with retaining flange. Three and five eighths inch (3-5/8") outside diameter by two and one eighth inch (2-1/8") inside diameter by one inch (1") height.
Radiator Mounting Pad
p/n: 30-0208-31
Pad, radiator lower splasher to grille. Fastens into place with rivets. One four (4) piece set required per car.Length: .875 inches. Width: .875 inches.
Firewall Grommet
p/n: 18-0015-20
This Firewall Grommet is designed to pass the cables and wires through the firewall. The seven (7) hole is for all 1937 models; fits retainer and can be altered into eight (8) hole type for all 1936 models.
Hood Bumper Set
p/n: 20-0356-42
This comprehensive Hood Bumper set is designed from the original part for superior fitment and function. The sixteen (16) piece set includes four (4) grille area bumpers and four (4) cowl bumpers with eight (8) rivets.
Rear Axle Bumpers
p/n: 20-0342-32
This Rear Axle Bumper pair is designed from the original part for superior fitment and function. Bumper is manufactured with top quality materials for good durability.
Hood Corner Pads
p/n: 40-0187-42
This Hood Corner Pad pair is an exact copy of the original. This pad fits between the engine hood and the body to isolate noise and vibration.
Engine Mount Pad
p/n: 27-0093-11
This Engine Mount Pad pair is used as an intermediate cushion or support. Made of a high-quality EPDM dense rubber to original specifications.
Transmission Mounting Pad
p/n: 11-0025-25
Mount, transmission. Original pattern, superior workmanship.
Fuel Neck Grommet
p/n: 30-0241-41
Grommet, gas tank inlet to wheel housing. Also used as grommet, gas tank inlet tube to wheel compartment bottom.
Flexible Run Channel
p/n: 20-1146-58
This Flexible Run Channel helps to eliminate window rattle, provides a smooth sliding surface for glass movement, and works to protect the glass. Stainless steel beaded. Available in sixty (60) inch strips.
Side Mount Grommet
p/n: 30-0079-37
Grommet, sidemount brace, lower, to fender. Hollow construction for good fit.
Brown Gearshift Boot
p/n: 40-0111-89
Boot, base of gearshift lever. Brown rubber. For black see our #40-0111-88. Made separately to fit most of our gearshift floorplates. Copied from original.
Door - Gravel Shield - Running Board Weatherstrip
p/n: 60-0054-73
This Door - Gravel Shield - Running Board Weatherstrip is a anti-squeak bulb type extrusion with fitment for General Motors vehicles. A twelve (12) foot strip made of high-quality EPDM dense rubber and designed from original parts for superior fitment, finish and function.