Horn Mounting Pad
p/n: 40-0194-21
Pad, horn grille housing mounting. Five and one fourth (5-1/4) inch by seventeen (17) inch overall.
Horn Trumpet Grommet
p/n: 70-1200-21
Grommets, horn trumpet mounting. One (1) inch inside diameter, 1-3/8 inch outside diameter, 9/16 inch high.
Horn trumpet grommet
p/n: 70-0302-21
Grommets, horn projector. For under hood horn brackets. Two (2) per car.
LaSalle monogram pedal pad
p/n: 70-0037-22
LaSalle pedal pads, clutch and brake, excellent copy from authentic original with LaSalle monogram.
License Light Mounting Pad
p/n: 40-0227-17
This License Light Mounting Pad is die cut from a dense rubber for a direct fit.
Lower Door Weatherstrips
p/n: 20-0391-73
This Lower Door Weatherstrip pair is designed from the original part for superior fitment and seal. These secondary door weatherstrips mount in channels on the cab body at the lower door opening. Works to seal the bottom of the doors against the vehicle body when the door is closed.
Lower Engine Mount
p/n: 20-1539-11
This Lower Engine Mount is designed from original part for correct fitment and function. Rubber coated over a metal core for durability and proper engine vibration isolation.
Luggage rack grommet
p/n: 70-0287-46
Grommets, luggage rack brace rod through body. Styles with luggage rack arms.
Masticated Rubber Sheet
p/n: 70-0645-45
This Masticated Rubber Sheet is three-thirty seconds (3/32) inch thick. The rubber sheet contains random milled cotton cord reinforcement for front end splash aprons, etc.
Peel-N-Stick Trunk Weatherstrip
p/n: 30-0356-WT
This trunk weatherstrip is designed from the original part for superior fitment and seal. The seal mounts around the full perimeter of the trunk directly to the body. Easy to install 3M Peel-N-Stick backing provides superior adhesion for reliable performance.
Peel-N-Stick Trunk Weatherstrip
p/n: 70-1691-WT
This Peel-N-Stick Trunk Weatherstrip is designed for superior fitment and seal. The self-adhesive weatherstrip mounts around the full perimeter of the trunk directly to the body. Easy to install 3M Peel-N-Stick backing provides superior adhesion for reliable performance.
Power Brake Holder
p/n: 17-0024-24
Holder, power brake B and K fitting to firewall, exact copy.Width: 1.625 inches. Height: 3.50 inches.
Pressure Ring
p/n: 70-0261-69
Pressure ring (washer), sponge rubber, interior door handle and window regulator escutcheon. One and three fourths (1-3/4) inches outside diameter by three eighths (3/8) inch thick.
Quarter vent weatherstrip
p/n: 40-0281-76
Weatherstrip, quarter window. Both sections, R & L, each made in one (1) strip to facilitate manufacturing. Must join two (2) ends together.
Quarter Window Weatherstrip
p/n: 40-0323-77
This Quarter Window Weatherstrip pair fits both the left- and right-hand windows. These weatherstrips are vulcanized for a seamless design and appearance.
Quarter Window Weatherstrips
p/n: 20-2122-77
This Quarter Window Weatherstrip is designed from the original part for superior fitment and seal. This seal mounts around the full perimeter of the left and right rear quarter glass for a precise, factory fit. Ends are not bonded. For stationary windows only.
Quarter Window Weatherstrips
p/n: 60-0282-77
This Quarter Window Weatherstrip pair is designed from the original part for superior fitment and seal. This channel weatherstrip mounts around the full perimeter of the quarter glass for a precise, factory fit. For stationary windows only.
Quarter Window Weatherstrips
p/n: 27-0040-77
This Quarter Window Weatherstrips pair is designed from the original part for superior fitment and seal. This seal mounts around the full perimeter of the quarter glass for a precise, factory fit. For fixed, stationary windows only.
Radiator Mounting Pad
p/n: 30-0469-31
Pad (or Grommet), radiator to dash tie rod. Die cut from one fourth (1/4) inch rubber. Four (4) used per car.Height: .25 inches.
Radiator Mounting Pad
p/n: 30-0208-31
Pad, radiator lower splasher to grille. Fastens into place with rivets. One four (4) piece set required per car.Length: .875 inches. Width: .875 inches.
Radio Antenna End Loop
p/n: 70-0105-21
End loop, radio antenna. Cord reinforced rubber with metal grommet. Mounted on running board on some models.
Rear Axle Bumpers
p/n: 20-0342-32
This Rear Axle Bumper pair is designed from the original part for superior fitment and function. Bumper is manufactured with top quality materials for good durability.
Rear Axle Bumpers - Revulcanization
p/n: 11-0030-35
This Rear Axle Bumpers - Revulcanization is designed to restore your original rubber bumper pads to a like new condition. Service requires your metal cores. Please call or email for more service details and ordering. Revulcanization service only.
Rear Bumper Grommet
p/n: 17-0014-29
Grommets, rear bumper. Excellent quality and craftsmanship. Fully molded rubber.
Rear Bumper Grommet
p/n: 60-0061-28
Grommets, rear bumper, right and left, for round bumper support bracket; left hand grommet has clearance for electrical conduit.
Rear Bumper Grommet
p/n: 27-0002-29
Grommets, rear bumper, right and left. Hollow construction, as original. Fully molded rubber.
Rear Bumper Grommet
p/n: 30-0197-29
Grommets, rear bumper. Molded left and right. Fully molded rubber.
Rear Bumper Grommet
p/n: 30-0137-29
Grommets, rear bumper support bar to body. Fully molded rubber w/ retaining flange.
Rear Bumper Grommet
p/n: 70-0104-29
Grommets, rear bumper, right and left. Large type with one and one fourth (1-1/4) inch by five (5) inch openings.
Rear Bumper Grommet
p/n: 30-0078-29
Grommets, rear bumper. Molded left and right as original with excellent detailing. Fully molded rubber with retaining flange.
Rear Bumper Grommet
p/n: 30-0047-29
Grommets, rear bumper. For models with luggage racks. Length: 4.125 inches. Width: 3.375 inches.
Rear door vent weatherstrip
p/n: 38-0020-74
Weatherstrip, rear door vent. Note: we do not have a matching metal core division post seal for this part. Please order our part #70-0040-56 separately.
Rear door vent weatherstrip
p/n: 38-0012-74
Weatherstrip, rear door vent window. Note: we do not have a matching metal core division post seal for this part. Please order our part #70-0040-56 separately.
Rear Door Weatherstrip Set
p/n: 90-1823-72
This Rear Door Weatherstrip Set is the primary door to body weatherstrip. Clips included for easy installation.
Rear Engine Mount
p/n: 70-0648-11
This Rear Engine Mount is used as an upper and lower support bracket at the transmission. Made from high-quality EPDM rubber for a precise, factory like fit.
Rear Leaf Spring Bushings
p/n: 70-0663-32
This Rear Leaf Spring Bushing pair is designed from the original part for superior fitment and function. Busing are for the rear leaf spring front or rear spring eyes.
Rear quarter vent weatherstrip
p/n: 17-0037-76
Weatherstrip, rear quarter vent. Sedans and enclosed drive Limousine having full swing quarter vent window ventilators.
Rear Quarter Vent Window Weatherstrips
p/n: 38-0021-76
This four (4) piece Rear Quarter Vent Window Weatherstrip set contains the main vent window seals and division post seal for the rear quarter window. All of the pieces were designed from original parts for a precise and like factory correct fit.
Rear Quarter Vent Window Weatherstrips
p/n: 30-0333-77
This Rear Quarter Vent Window Weatherstrip pair is designed from the original parts for superior fitment and seal. A two (2) piece pair that fits both driver (Left) and passenger (Right) sides of the rear quarter panel vent / wing window assemblies.
Rear Spring Bumper
p/n: 60-0137-32
Bumper, rear spring. Fits original retainer.Width: 2.5625 inches.
Rear Spring Bumpers
p/n: 60-0179-35
This Rear Spring Bumper pair is designed from the original part for an authentic fit, finish, and appearance. Mounts to the frame for the rear springs. An assembly with rubber vulcanized to steel as original.
Rear spring bushing
p/n: 60-0311-35
Bushing, rear spring front eye, inlox cartridge type as original.
Rear Spring Pad
p/n: 70-0191-32
Pad, rear spring insulator for two (2) inch wide springs. (see our number 70-0245-32 for two and one fourth (2-1/4) inch springs). Cloth reinforced. Four (4) per vehicle.
Rear Spring Pad
p/n: 27-0010-35
Pad, rear spring insulator for one and three fourths (1-3/4") inch wide springs. Four (4) per vehicle.
Rear Spring Pad
p/n: 70-0245-32
Pad, rear spring insulator for two and one fourth (2-1/4) inch wide springs. (see our number 70-0191-32 for two (2) inch springs). Four (4) per vehicle.
Rear Spring Thrust Washer
p/n: 40-0525-32
Thrust washer, rear spring. "Silent Block". Three sixteenths (3/16) inch thick. One (1) inch by one and three fourths (1-3/4) inch.
Rear Spring Thrust Washer
p/n: 40-0526-32
Thrust washer, rear spring. "Silent Block". Three sixteenths (3/16) inch thick. Seven eighths (7/8) inch by one and five eighths (1-5/8).
Rear Stabilizer Bushing
p/n: 70-0905-33
Bushing, rear stabilizer ends. Four (4) required per car. Fully molded rubber.
Rear Window Division Bar Seal
p/n: 70-0475-82
Pad/Gasket set, back window division bar mounting. Set of four (4) pads, inner and outer, for two (2) dividers. Three fourths (3/4) inch wide.
Rear window division bar seal
p/n: 70-0068-82
Seal, rear window divider, inner and outer for two (2) and three (3) light rear windows, two (2) piece set for one (1) division bar.
Rear Window Division Bar Seal
p/n: 40-0285-77
Gasket, back window division bar. Closed body styles with split back window.Length: 9.25 inches. Width: 1.125 inches.
Rear Window Gasket
p/n: 70-0687-81
This Rear Window Gasket is designed from the original part for superior fitment and seal. The seal mounts around the full perimeter of the back glass and has vulcanized, or bonded, ends which means no cutting or splicing is required for installation.
Rear Window Gasket
p/n: 60-0330-81
This Rear Window Gasket is designed from the original part for superior fitment and seal. The seal mounts around the full perimeter of the back glass and has vulcanized, or bonded, ends which means no cutting or splicing is required for installation.
Rear Window Gasket
p/n: 60-0433-81
This Rear Window Gasket is designed from the original part for superior fitment and seal. The seal mounts around the full perimeter of the back glass and has vulcanized, or bonded, ends which means no cutting or splicing is required for installation.