Stabilizer Shaft Link Bushing
p/n: 60-0317-33
This Stabilizer Shaft Link Bushing works to support the vehicle front stabilizer or sway bar shaft. Six (6) required per vehicle.
Front coil spring pad
p/n: 50-0358-35
Insulators, front coil spring. Fabric reinforced rubber as original.
Cowl Vent Gasket
p/n: 20-1613-54
This Cowl Vent Gasket is designed from the original part for superior fitment and seal. Manufactured to OEM specifications to install for an authentic fit and finish.
Firewall Grommet
p/n: 40-0221-21
This Firewall Grommet is used to run the speedometer cable, oil tube, and the temperature tube through the firewall. The three (3) holes measure 5/16", 1/4", 3/16".
Starter Button Cover
p/n: 60-0322-21
This Starter Button Cover is designed from the original part for an authentic fit, finish, and appearance. A push on replacement to rod. Two (2") inch outside diameter.
Door Weatherstrip
p/n: 20-0390-72
This Door Weatherstrip is the primary door to body weatherstrip. Includes enough to do front, top and backside of one door. Order two (2) for both doors.
Clutch and Brake Pedal Pads - Black
p/n: 50-0054-22
This reproduction Clutch and Brake Pedal Pad pair slips over the full perimeter of the pedal for a precise, factory fit. A perfect reproduction to replace worn original pedal pads. Manufactured in quality black rubber.
Taillight Lens Gasket
p/n: 60-0100-15
Gasket, taillight lens.Length: 5.125 inches. Width: 1.875 inches.
2-1/2" Firewall Grommet
p/n: 30-0111-21
This Firewall Grommet is used to run the speedometer cable through the firewall. The grommet is retained by a steel collar, not included.
Firewall Grommet
p/n: 40-0222-21
This Firewall Grommet is used to run the throttle cable and wiper vacuum line through the firewall as well as a drain hole for the cowl vent. The holes in the three (3) hole design measure: 9/16", 3/8", and 1/4".
Convertible Weatherlip
p/n: 70-0616-67
Weather deflector, edge of folding top fabric near folding post, mounted on body.
Handbrake Seal
p/n: 60-0396-24
Seal, handbrake at floorboard. Rubber sponge, one (1) required per vehicle.Length: 4.50 inches. Width: 2.0 inches. Height: 1.25 inches.
Accelerator Rod Seal
p/n: 40-0205-88
This Accelerator Rod Seal is used as an accelerator rod through the toeboard. Molded from a high-quality EPDM dense rubber.
Hood to Cowl Weatherstrip
p/n: 60-0138-42
This Hood To Cowl Weatherstrip pair installs at the rear of the engine bay to seal between the hood and vehicle body cowl. Sold as a pair for left and right side.
Bumper Seal
p/n: 70-0563-45
Filler valance or deflector, rear. Eight (8) inches long (cut shorter where required), three (3) to four (4) required per car.
Fuel Neck Grommet
p/n: 60-0049-41
Grommet, fuel filler neck with proper retaining flange. Oval style. Three and three fourths inch (3-3/4) outside width by four and one half inch (4-1/2") outside length by three fourths (3/4") inch height.
Trunk Handle Mounting Pad
p/n: 50-0200-87
Mounting pad, trunk handle escutcheon.Length: 6.75 inches.
Brake and Clutch Shank Seal
p/n: 50-0066-24
Grommet, brake and clutch pedal floor seal.Width: 1.8125 inches. Height: 2.375 inches.
Trunk Weatherstrip
p/n: 20-1688-84
This Trunk Weatherstrip is designed from the original part for superior fitment and seal. The seal mounts around the full perimeter of the trunk directly to the body.
Brown Gearshift Boot - Steering Column
p/n: 30-0069-89
This steering column Gearshift Boot is designed from the original part for superior fitment, finish and function. Brown rubber. Two and one quarter (2-1/4) inches long.