Track Bar Bushing
p/n: 25-0080-32
Bushing, rear axle track bar. Made in halves for easier replacement. Sold in pairs, two (2) pair needed per bar.Height: .75 inches.
Fender Welting
p/n: 20-1590-44
This black Fender Welting is designed from the original part for superior fitment and seal. This welting material fits between the fenders and the vehicle body. Thirty (30) foot roll.
Gearshift Seal
p/n: 60-0471-24
This Gearshift Seal is designed from the original part for superior fitment and function. For the gearshift at floor.
Flexible Run Channel - 30 Inch Pair
p/n: 40-0309-57
Channel, side window glass, vertical run. Flexible, felt lined, rubber covered channel. Available in 30" pair.
Door Lock Weatherstrip
p/n: 50-0172-70
Weatherstrip, door lock, front and rear. Protects door lock mechanism from dust and weather.Length: 3.625 inches.
2-3/8" Firewall Grommet
p/n: 70-0185-20
This Firewall Grommet is used to run the main wiring harness in addition to five (5) accessory wires through the firewall. Designed from the original part for superior fit and seal.
Hood to Cowl Weatherstrip
p/n: 60-0056-42
This Hood to Cowl Weatherstrip is extruded from a high quality dense rubber for a durable and proper seal. This seal mounts at the rear of the engine bay to seal between the hood and vehicle body cowl.
Antenna Mount Pad
p/n: 70-2621-21
Pad, roof mounted antenna gasket. Models with antenna mounted above center of windshield.
Lock Cylinder Gasket
p/n: 30-0022-71
Pads, door handle escutcheon.Width: 1.875 inches. Height: 1.375 inches.
Antenna Wire Mount
p/n: 70-2263-19
Mount, radio antenna wire, under running board. Found on several models with factory type antennas that mount under the running board.
Rigid Run Channels
p/n: 70-0516-58
This Rigid Run Channel pair is zinc plated steel with black cloth inside lining to provide a smooth sliding surface for glass movement. Also works to protect the glass. Fastens in place by small screws or rivets on top and bottom.
Convertible Top Rest Bump Stop Block
p/n: 70-0397-67
This Convertible Top Rest Bump Stop Block pair is designed from the original part for an authentic fit, finish, and appearance. Attaches to the folding pillar arm of the convertible top assembly. This rubber only bumper block glues to the original metal core.
Cowl Vent Gasket
p/n: 60-0081-54
Gasket, cowl vent. These parts are made of the highest quality and authenticity.Length: 15.0 inches.
Division bar chrome retainer
p/n: 70-3226-51
Retainer (rubber), outer windshield, stainless center post molding. Use with original stainless molding and clips.
Brake and Clutch Shank Seal
p/n: 40-0175-24
Seal, brake and clutch pedal shank to floorboard. One and one half (1-1/2) inch by two and one eighth (2-1/8) inch by three fourths (3/4) inch thick.
Cowl vent weatherstrip
p/n: 70-0143-54
Gasket, cowl vent. Perfect copy of original, not a sponge substitute, top quality material.
Steering gear bushing
p/n: 30-0340-36
Bushing, steering gear lever ball stud (Pitman arm). Originally made in one piece as spool bushing, but replacements made in halves.
Backup Light Mounting Pad
p/n: 60-0072-17
Mounting pads, back up lights, elliptic, sharp beaded edge. One and five sixteenths (1-5/16) inch by two and seven eighths (2-7/8) inch.Length: 2.
Division Bar Grommet
p/n: 70-0272-62
Grommets, rear door vent divider post, top and bottom, right and left.
Door Lower Weatherstrips
p/n: 20-1652-73
This three (3) piece Lower Door Weatherstrip set is designed from the original part for superior fitment and seal. Use full-length for front doors, cut third piece in half to complete installation for both rear doors.