Splash Apron / A-Arm Dust Shield
p/n: 70-3064-45
This two (2) piece Splash Apron / A-Arm Dust Shield Filler set is designed from the original part for superior fitment and seal. Filler pieces are die cut from quality masticated rubber to authentic original dimensions. Pieces fit over suspension a-arms and inside front inner fenders.
Cowl Vent Gasket
p/n: 20-0556-54
This Cowl Vent Gasket is designed from the original part for superior fitment and seal. Manufactured to OEM specifications to install for an authentic fit and finish.
Stabilizer bushing
p/n: 20-1295-33
Bushings, stabilizer bar to frame. One (1) pair required per car.
Hood Bumper Set
p/n: 20-0545-42
This six (6) piece Hood Bumper set is designed from the original parts for superior fitment and function. This set fits F Series Trucks.
Steering Column Floorplate
p/n: 20-1694-88
Seal, steering column tube. Installs on top of floor mat.
Rocker Panel Inner Drain Cover
p/n: 70-2392-45
This Rocker Panel Inner Drain Cover pair is designed from the original part for superior fitment and seal. Fully molded with proper attaching teeth and flap.
Hydraulic Pump Mounting Pad
p/n: 70-1610-67
Cushion mount, hydraulic pump.Width: .6875 inches. Height: 1.0 inches.
Firewall to Hood Weatherstrip - Cowl Lacing
p/n: 20-3006-43
This Firewall to Hood Weatherstrip - Cowl Lacing is designed from the original part for superior fitment and seal. This seal mounts with installation tacks at the rear of the engine bay firewall directly to the body.
Steering Column Floorplate
p/n: 20-3158-88
Seal, steering column to floor. Installs under floor mat.
Battery Clamp Cover
p/n: 70-0095-21
This Battery Clamp Cover helps to protect the nearby metal and finish. Fully molded from high-quality EPDM rubber to ensure durability. Good copy from an original part.
Quarter Window Vertical Leading Edge
p/n: 70-0141-58
This quarter to side window Vertical Leading Edge Weatherstrip pair is designed from the original part for superior fitment and seal. Slides into metal retaining channel attached to rear side window and seals between the front door window and the rear quarter window.
Hydraulic Pump Mounting Cushion
p/n: 70-0852-67
This Hydraulic Pump Mounting Cushion is designed from the original part for superior fitment and function. Used on models with hydraulic window lifts or a hydraulic convertible top. Two (2) to three (3) required per car.
Rear Bumper End Fillers
p/n: 70-3774-30
This two (2) piece Rear Bumper End Filler pair is designed from the original part for a superior fitment level. These die cut masticated rubber pieces fit to the left and right bumper ends between the rear bumper and the vehicle body.
Brake Master Cylinder Push Rod Boot
p/n: 60-0180-24
This Brake Master Cylinder Push Rod Boot is made from high-quality Nitrile rubber for a precise, factory like fit for your classic vehicle. Manufactured to OEM specifications to install for an authentic fit and finish.
Stabilizer Bar End Link Set
p/n: 60-0221-33
Twenty-two (22) piece Stabilizer Bar End Link set for both sides of one (1) vehicle, fits front or rear bar. Order two (2) sets for vehicles with front and rear stabilizer bars. Hex head bolt 3/8"-16 NF x 6-15/16" long. Comes with metal sleeve, metal cup washers and rubber grommets.
Battery Hole Cover Seal
p/n: 20-0555-21
This Battery Hole Cover Seal is designed from the original part for superior fitment and seal. This part seals the battery hole cover to the vehicle floor.
Firewall Grommet
p/n: 70-2066-24
This Firewall Grommet is used to run the emergency brake cable through the firewall. Designed from the original part for superior fit and seal.
Starter Pedal Button Cover
p/n: 60-0166-21
This Starter Button Pedal Cover is designed from the original part for an authentic fit, finish, and appearance. Rubber slip over type for old metal. Two (2") inch outside diameter.