Spark plug grommet
p/n: 70-1180-21
Grommet, spark plug & coil wire at distributor cap outlets. For nine (9mm) millimeter wire, earlier years.
Spark Plug Wire Spacer
p/n: 70-0394-21
This Spark Plug Wire Spacer is designed from the original part for superior fitment and function. This spacer fits spark plug wires into the organizer bracket.
Splash Apron
p/n: 20-3015-44
This six (6) piece Splash Apron set is designed from the original part for superior fitment and seal. Includes fender splash apron and bottom of radiator side deflectors.
Splash Apron / A-Arm Dust Shield
p/n: 70-3064-45
This two (2) piece Splash Apron / A-Arm Dust Shield Filler set is designed from the original part for superior fitment and seal. Filler pieces are die cut from quality masticated rubber to authentic original dimensions. Pieces fit over suspension a-arms and inside front inner fenders.
Spring seat service
p/n: 60-0619-35
Seat, rear spring. Revulcanization service only. Send in complete casting with metal sleeve bushing.
Spring Shackle Bushing Set
p/n: 20-0550-32
This Spring Shackle Bushing Set is used on both springs. This kit does NOT include the shackle bars used on the front of the spring.
Spring Shackle Bushing Set
p/n: 20-2481-33
This Spring Shackle Bushing Set is for the front of the rear leaf spring. Two (2) kits required per car.
Spring Shackle or Shock Absorber Link Bushing
p/n: 20-1274-32
This Bushing is manufactured to OEM specifications to install for an authentic fit, finish and function. Used for front or rear leaf spring on Ford models. Used as a rubber, shock absorber link bushing on Chrysler models.
Stabilizer Bar End Link Set
p/n: 60-0221-33
Twenty-two (22) piece Stabilizer Bar End Link set for both sides of one (1) vehicle, fits front or rear bar. Order two (2) sets for vehicles with front and rear stabilizer bars. Hex head bolt 3/8"-16 NF x 6-15/16" long. Comes with metal sleeve, metal cup washers and rubber grommets.
Stabilizer Bar End Link Set
p/n: 70-0567-34
Twenty-two (22) piece Stabilizer Bar End Link set for both sides of one (1) vehicle, fits front or rear bar. Order two (2) sets for vehicles with front and rear stabilizer bars. Hex head bolt. 5/16"-24NF x 7-5/8" long. Includes metal sleeves, cup washers and rubber grommets.
Stabilizer Bushing
p/n: 27-0085-34
Bushings, for stabilizer bracket. Fully molded rubber. Correct dimensions, not an aftermarket replacement.
Stabilizer Bushing
p/n: 70-0627-33
Bushings, stabilizer bar, front. Fully molded rubber. One and three fourths inch (1 3/4") length by one and one half inch (1 1/2") width by three fourths inch (3/4") inside hole diameter by one and five eighths inch (1 5/8") height.
Stabilizer bushing
p/n: 20-1295-33
Bushings, stabilizer bar to frame. One (1) pair required per car.
Stabilizer Link or Shock Grommet
p/n: 70-0737-33
This Stabilizer Link or Shock Grommet is designed from the original part for superior fitment and usage. Fully molded rubber.
Standard rubber washer
p/n: 60-0726-45
Washer, for attaching moldings, emblems, and fender guards as required on body.
Starter Button Cover
p/n: 60-0322-21
This Starter Button Cover is designed from the original part for an authentic fit, finish, and appearance. A push on replacement to rod. Two (2") inch outside diameter.
Starter Pedal Bellows
p/n: 60-0210-21
This Starter Pedal Bellows is designed from the original part for an authentic fit, finish, and appearance. This bellows fits to the starter pedal shaft to floorboard.
Starter Pedal Button Cover
p/n: 60-0166-21
This Starter Button Pedal Cover is designed from the original part for an authentic fit, finish, and appearance. Rubber slip over type for old metal. Two (2") inch outside diameter.
Starter Solenoid Cable Rubber Boot
p/n: 70-0704-21
This Starter Solenoid Cable Rubber Boot is designed from the original part for superior fitment and function. This boot covers and protects the battery cable at the starter solenoid connection.
Steel Quarter Window Sash Channel - Left Front Door
p/n: 20-3059-58
This reproduction Steel Quarter Window Sash Channel is designed from the original part for superior fitment and function. This channel is for the Left Front Door.
Steel Quarter Window Sash Channel - Right Front Door
p/n: 20-3058-58
This reproduction Steel Quarter Window Sash Channel is designed from the original part for superior fitment and function. This channel is for the Right Front Door.
Steel Sash Channel
p/n: 20-0514-62
This reproduction Steel Sash Channel is designed from the original part for superior fitment and function. This glass channel is for the Left or Right Front Door.
Steel Sash Channel - Left Front Side
p/n: 20-3053-58
This reproduction Steel Sash Channel is designed from the original part for superior fitment and function. This channel is for the Left Front Door.
Steel Sash Channel - Left Front Side
p/n: 20-3045-58
This reproduction Steel Sash Channel is designed from the original part for superior fitment and function. This channel is for the Left Front Door.
Steel Sash Channel - Right Front Door
p/n: 20-3052-58
This reproduction Steel Sash Channel is designed from the original part for superior fitment and function. This channel is for the Right Front Door.
Steel Sash Channel - Right Front Door
p/n: 20-3044-58
This reproduction Steel Sash Channel is designed from the original part for superior fitment and function. This channel is for the Right Front Door.
Steel Sash Channel - Right Rear Door
p/n: 20-3056-58
This reproduction Steel Sash Channel is designed from the original part for superior fitment and function. This channel is for the Right Rear Door.
Steering Column Connecting Rod Seal
p/n: 60-0400-36
Steering column steering connecting rod seal. Power steering models require one (1) per car. Non-power steering models require two (2) per car.
Steering Column Cushion
p/n: 40-0422-36
Insulator set, steering housing to frame. Set includes both inner and outer pieces.Length: 4.125 inches.
Steering Column Finish Strip
p/n: 70-1707-88
Seal, steering column to instrument panel. Extruded rubber strip thirteen (13) inch to exact cross-section.Length: 13.0 inches. Width: .625 inches.
Steering Column Floorplate
p/n: 20-0549-88
Seal, steering column, brake and clutch arms to floor. Floor shift models.
Steering Column Floorplate
p/n: 70-2578-36
Floor plate, steering column at floorboard. Durable black rubber construction with metal core just like original.
Steering Column Floorplate
p/n: 20-0587-36
This Steering Column Floorplate pad wraps between the steering column and bracket. The pad is used to reduce noise between the steering column and the dash.
Steering Column Floorplate
p/n: 20-1694-88
Seal, steering column tube. Installs on top of floor mat.
Steering Column Floorplate
p/n: 20-0548-88
Seal, steering column, brake and clutch arms to floor. Column shift models. Installs under metal plate.
Steering Column Floorplate
p/n: 20-3158-88
Seal, steering column to floor. Installs under floor mat.
Steering Column Floorplate Gasket
p/n: 60-0395-36
This Steering Column Floorplate Gasket is designed from the original part for superior fitment and seal. Cover (grommet), steering gear-to-toe board seal. Width: 5-13/16" inches. Height: 6" inches.
Steering Column Gasket
p/n: 70-2317-88
Insulator, steering column lower mounting frame gasket. Triangular shape with mounting holes and column tube clearance.
Steering Column Grommet
p/n: 60-0436-32
Grommet, steering gear. Molded with metal core as original with all original features.Length: 4.375 inches.
Steering Column Grommet
p/n: 40-0421-36
Grommet, steering column and transmission shift rod through firewall.Length: 4.375 inches.
Steering Column Grommet
p/n: 70-2516-36
Grommet, steering column to dash at floorboard. Black rubber. For brown see our #70-2516-89. Fully molded with correct metal core.
Steering Column Seal
p/n: 60-0518-36
Seal, steering column and shift column toe pan. Five eighths (5/8) inch thick sponge rubber.Width: 4.875 inches. Height: .625 inches.
Steering Column Seal
p/n: 60-0435-32
Seal, steering column at toe pan, sponge.Length: 5.375 inches. Height: .25 inches.
Steering Knuckle Support Seal
p/n: 50-0199-35
Seal, steering knuckle support, upper pivot pin. Four (4) required per car.Height: .5 inches.
Suspension arm bumper
p/n: 70-1021-32
Bumper, front or rear suspension, upper. Uses two (2) per car on front suspension, one (1) per car on rear.
Suspension Bumper - Front Lower Control Arm
p/n: 50-0092-32
This Suspension Bumper is designed from the original part for superior fitment and function. Bumper mounts to the front suspension lower control arm. Two (2) per car required.
Tailgate Bumper
p/n: 20-0694-45
These Tailgate Bumpers are sold as pair. The bumpers fit in brackets and comes with chains.
Taillight Gasket Set
p/n: 70-0876-15
This eight (8) piece Taillight Lens Gasket set is designed from the original part for superior fitment and seal. The set includes steel rule die-cut and molded rubber gaskets for the taillight lens and body mounting to fender.
Taillight Gaskets
p/n: 60-0671-15
This Taillight To Fender Gasket pair is designed from the original part for superior fitment and sealing. These reproduction gaskets fit between taillight frame housing and the body. Two 1/4" strips of sponge rubber cut 26-3/4" long. One (1) pair required per vehicle.
Taillight Lens Gasket
p/n: 20-0411-15
Gaskets, taillight lens. Cork.Ford Truck 1948-56 Gaskets, lens to housing. Ford Cars 1941 Gaskets, taillight lens.
Taillight Mounting Pad
p/n: 50-0382-15
Taillight to fender mounting pad. Excellent quality molded piece with all correct details. Four (4) required per car.
Taillight Mounting Pad
p/n: 30-0366-15
Pad or Gasket, taillight to body. One (1) pair required per car, sold only in pairs.
Taillight Retainer Pad
p/n: 60-0340-17
This Taillight Retainer Pad is designed from the original part for superior fitment and seal. These reproduction mounting pads fit to the rear taillight assembly.
Threaded Ends Insulator for Propeller Shaft and Exhaust Muffler
p/n: 70-0631-27
A steel core, double end threaded quality rubber Insulator that functions as an exhaust system muffler pipe bracket insulator. Also functions as a propeller shaft bearing to frame crossmember insulator.
Tie Rod Dust Covers
p/n: 20-2484-36
This Tie Rod Dust Cover, drag link seal, is sold as a four (4) piece set. The seals are designed from originals for proper fitment.
Torque ball service
p/n: 50-0190-27
Retainer, torque ball, heavy steel jacket with molded rubber inner collar. Revulcanization service only.