Side Window Leading Edge
p/n: 30-0475-57
Weatherstrip, quarter window leading edge.Length: 12.125 inches. Width: .8125 inches.
Side Window Lift Limit Cap
p/n: 60-0071-62
Caps, side window lift limit. Rubber, snap-over type, three fourths (3/4) inch diameter by five sixteenths (5/16) inch thick.
Side Window Roller
p/n: 70-0117-62
This Side Window Roller, anti-rattle roller, is manufactured using EPDM dense rubber to replace the original perfectly. The roller fits both styles of brackets.
Side Window Run Channel and Beltline Set
p/n: 20-1622-60
This six (6) piece Side Window Run Channel and Beltline set is designed from the original part for superior fitment and function. This door glass anti-rattler set includes fastener hardware and comes ready to install.
Side Window Sash Channel
p/n: 70-0641-58
This Side Window Sash Channel is the u-shaped steel channel only, no filler. Sold in 4 foot strip, usually sufficient for two (2) windows.
Side Window Weatherstrip Deluxe Set
p/n: 20-0472-60
This Side Window Weatherstrip Deluxe Set is for both truck doors and includes the back edge of vent window seal installed, beltline weatherstrips, door glass runs with rivets and original-type vent bar channel with brackets riveted in place.
Side Window Weatherstrip Set
p/n: 70-4633-60
This Side Window Weatherstrip Set is for both truck doors and includes the window felt beltline weatherstrips, door glass runs and original-type vent division bar channels. This is a basic replacement set with no run channel clips or division bar brackets.
Side Window Weatherstrip Set
p/n: 90-3288-90
This six (6) piece Side Window Weatherstrip Set is designed for superior fitment and function. The set contains the flexible run channels and the window felt beltline weatherstrips needed for the side window glass. The set does two (2) front doors.
Sliding Quarter Window Seal
p/n: 60-0398-78
Weatherstrip, sliding quarter window. Mounted vertically in body where leading edge of sliding window fits when closed. Right & left rubber only.
Sliding Quarter Window Weatherstrip
p/n: 70-0353-78
This Sliding Quarter Window Weatherstrip is used for side window inner and/or outer, front and/or rear doors. Available in a 6ft. lengths.
Spark plug grommet
p/n: 70-1180-21
Grommet, spark plug & coil wire at distributor cap outlets. For nine (9mm) millimeter wire, earlier years.
Spark plug retaining ring
p/n: 30-0352-21
Retaining ring, spark plug wire. Two (2) per car.Chevrolet 1935-48 Retaining ring, spark plug wire. Two (2) per car. All models.
Speedometer Housing Grommet
p/n: 20-0447-20
This Speedometer Housing Grommet is used where the cable runs through the floorboard. Also allows for the choke and throttle cable to go through the firewall.
Spring eye bushing
p/n: 10-0131-35
Bushing, spring eye, both eye leaf and shackle. Front and rear.Qty Required:20 Twelve (12) required per front, eight (8) required per rear.
Spring seat service
p/n: 60-0619-35
Seat, rear spring. Revulcanization service only. Send in complete casting with metal sleeve bushing.
Spring Shackle Bushing
p/n: 40-0183-32
Bushing, spring and shackle, front and rear leaf springs. Eight (8) or twelve (12) required per car.Length: 1.25 inches. Height: 1.25 inches.
Spring Shackle Bushing
p/n: 30-0344-32
Bushing, rear spring and shackle. One and one eighth (1-1/8) inch diameter with nine sixteenths (9/16) inch hole. One set contains twelve (12) pieces.
Spring Shackle Bushing Set
p/n: 20-1581-33
This Spring Shackle Bushing Set is for the rear leaf springs. This set is an original steel stud type.
Spring Shackle Bushing Set
p/n: 20-1580-33
This Spring Shackle Bushing Set is for the front leaf springs. This set is an original steel stud type.
Spring shackle seal
p/n: 70-1125-33
Washer, front and rear spring shackle, seal for shackle pin. Constructed of neoprene.
Stabilizer Bar End Link Set
p/n: 70-0567-34
Twenty-two (22) piece Stabilizer Bar End Link set for both sides of one (1) vehicle, fits front or rear bar. Order two (2) sets for vehicles with front and rear stabilizer bars. Hex head bolt. 5/16"-24NF x 7-5/8" long. Includes metal sleeves, cup washers and rubber grommets.
Stabilizer Bar End Link Set
p/n: 60-0221-33
Twenty-two (22) piece Stabilizer Bar End Link set for both sides of one (1) vehicle, fits front or rear bar. Order two (2) sets for vehicles with front and rear stabilizer bars. Hex head bolt 3/8"-16 NF x 6-15/16" long. Comes with metal sleeve, metal cup washers and rubber grommets.
Stabilizer Bushing
p/n: 70-0627-33
Bushings, stabilizer bar, front. Fully molded rubber. One and three fourths inch (1 3/4") length by one and one half inch (1 1/2") width by three fourths inch (3/4") inside hole diameter by one and five eighths inch (1 5/8") height.
Stabilizer Grommet
p/n: 30-0310-33
Grommet, front or rear stabilizer links, lower. Fully molded rubber.
Stabilizer Grommet
p/n: 70-0221-33
Grommet, rear stabilizer bar (angular sway bar). Four (4) required per car. Fully molded rubber.
Stabilizer Link or Shock Grommet
p/n: 70-0737-33
This Stabilizer Link or Shock Grommet is designed from the original part for superior fitment and usage. Fully molded rubber.
Starter Button Cover
p/n: 60-0322-21
This Starter Button Cover is designed from the original part for an authentic fit, finish, and appearance. A push on replacement to rod. Two (2") inch outside diameter.
Starter Pedal Bellows
p/n: 60-0210-21
This Starter Pedal Bellows is designed from the original part for an authentic fit, finish, and appearance. This bellows fits to the starter pedal shaft to floorboard.
Starter Pedal Button Cover
p/n: 60-0166-21
This Starter Button Pedal Cover is designed from the original part for an authentic fit, finish, and appearance. Rubber slip over type for old metal. Two (2") inch outside diameter.
Starter Pedal Pad
p/n: 25-0049-89
Pad, starter pedal. Original pattern, brown rubber, exact copy.Height: .50 inches.
Starter Solenoid Cable Rubber Boot
p/n: 70-0704-21
This Starter Solenoid Cable Rubber Boot is designed from the original part for superior fitment and function. This boot covers and protects the battery cable at the starter solenoid connection.
Steel Sash Channel - Door Glass
p/n: 20-0473-58
This reproduction Steel Sash Channel is designed from the original part for superior fitment and function. This left or right door glass channel fits in the bottom of door for the glass to sit in.
Steering Column Cushion
p/n: 40-0422-36
Insulator set, steering housing to frame. Set includes both inner and outer pieces.Length: 4.125 inches.
Steering Column Cushion
p/n: 20-0453-36
This Steering Column Cushion is the steering column bracket to dash pad. This cushion is used as a noise reducer.
Steering Column Floorplate
p/n: 20-1694-88
Seal, steering column tube. Installs on top of floor mat.
Steering Column Floorplate
p/n: 20-0449-88
Seal, brake, clutch and steering column to floor. Column shift models. Installs under metal plate at floor.
Steering Column Floorplate
p/n: 20-0450-88
Seal, brake, clutch and steering column to floor. Floor shift models.
Steering Column Floorplate
p/n: 20-0451-88
Seal, steering column to floor mat. Column shift models. Installs on top of mat.
Steering Column Floorplate
p/n: 20-0452-88
Seal, steering column to floor mat. Floor shift models. Includes hold down clips.
Steering Column Gearshift Vacuum Boot
p/n: 60-0555-24
This Steering Column Vacuum Cylinder Boot is designed from the original part for superior fitment, finish and function. An excellent duplicate of original.
Steering Column Grommet
p/n: 60-0436-32
Grommet, steering gear. Molded with metal core as original with all original features.Length: 4.375 inches.