Door Check Link Rod End Stop
p/n: 70-0479-70
End nut, check link (rubber bar with steel bar insert). Three fourths (3/4) inch by three fourths (3/4) inch by two (2) inch threaded five sixteenths (5/16) inch. (For round stop nut, see our #70-0326-70).
Windshield Division Bar Gasket
p/n: 70-0098-52
This Windshield Division Bar Gasket is designed from the original part for superior fitment and seal. Part combines inner and outer gasket in one piece as original. For seventeen (17") inch to (20") inch lengths.
2-1/4" Firewall Grommet
p/n: 50-0166-20
This Firewall Grommet is used to run the wiring harness through the firewall mat. Designed from the original part for superior fit and seal.
Power brake carpet grommet
p/n: 70-3147-24
Grommet, carpet. Floor front carpet grommet use for power brake hole.
Threaded Ends Insulator for Propeller Shaft and Exhaust Muffler
p/n: 70-0631-27
A steel core, double end threaded quality rubber Insulator that functions as an exhaust system muffler pipe bracket insulator. Also functions as a propeller shaft bearing to frame crossmember insulator.
Door Weatherstrips - Lower
p/n: 60-0078-73
This Lower Door Weatherstrip pair is designed from the original parts for superior fitment and seal. Heavy type with original ribbing and retainer lip.
Hood Bumper Set
p/n: 20-1588-42
This twelve (12) piece Hood Bumper set is designed from the original parts for superior fitment and function.
Quarter Window Vertical Leading Edge
p/n: 20-1656-76
This Quarter Window Vertical Leading Edge Weatherstrip pair is designed from the original part for superior fitment, finish and function. This part fits Ford convertible only and is the weatherstrip that holds the quarter window glass in the frame.
Gearshift Boot - Brown
p/n: 20-2166-26
This Gearshift Boot is designed from the original part for superior fitment and seal. This boot fits over the gearshift tower to make a weathertight connection for the transmission gearshift rod as it passes up through the vehicle floorboard.
1-1/2" Firewall Grommet
p/n: 70-0186-20
This Firewall Grommet is used to run the vacuum operated radio antenna lines through the firewall. Designed from the original part for superior fit and seal.
Starter Pedal Pad
p/n: 25-0049-89
Pad, starter pedal. Original pattern, brown rubber, exact copy.Height: .50 inches.
Parking light gasket
p/n: 70-2652-16
Gaskets, front parking light, lens gasket. For lamp base see our #70-2651-16.
Clutch and Brake Pedal Bumpers
p/n: 60-0104-24
This Clutch and Brake Pedal Bumper is designed from the original part for superior fitment, finish and function. Pedal shank rides under floorboard. One and one-eighth (1-1/8") inch clearance for pedal shaft.
Clutch and Brake Pedal Bumpers
p/n: 60-0579-24
This Clutch and Brake Pedal Bumper is designed from the original part for superior fitment, finish and function. This pedal to floorboard bumper is the longer type with one and three-eighths (1-3/8") inch clearance for the pedal shaft.
Black Gearshift Boot - Steering Column
p/n: 30-0069-36
This steering column Gearshift Boot is designed from the original part for superior fitment, finish and function. Black rubber. Two and one quarter (2-1/4) inches long.
Rear Spring Pad
p/n: 70-0245-32
Pad, rear spring insulator for two and one fourth (2-1/4) inch wide springs. (see our number 70-0191-32 for two (2) inch springs). Four (4) per vehicle.
Clutch and Brake Pedal Pads
p/n: 60-0218-22
This reproduction Clutch and Brake Pedal Pad pair slips over the full perimeter of the pedal for a precise, factory fit. A perfect reproduction to replace worn original pedal pads. Manufactured in quality black rubber.
Front coil spring pad
p/n: 50-0358-35
Insulators, front coil spring. Fabric reinforced rubber as original.
Cowl to Fender Seal
p/n: 20-0443-45
Seal, front fender to cowl. Soft pliable sponge rubber designed to accurately fill the gaps between the back side of the fender and cowl. May be supplied as single strip that customer will have to cut in order to facilitate installation.
Rear Window Gasket
p/n: 20-0479-81
This Rear Window Gasket is designed from the original part for superior fitment and seal. The seal mounts around the full perimeter of the back glass and has vulcanized, or bonded, ends which means no cutting or splicing is required for installation.