Vent Window Division Post Seals
p/n: 70-4333-56
This Front Vent Window Division Post Seal pair is designed from the original part for superior fitment and seal. Parts are fully molded EPDM rubber over a brass metal core.
Headlight seal
p/n: 70-2574-14
Seal, headlight to front fender retainer seal. Fully molded to fit like original, unlike a extruded strip that will buckle.
Axle Rebound Pad
p/n: 30-0534-32
Bumper, rear axle rebound.Length: 3.0 inches. Width: 2.375 inches. Height: 1.6875 inches.
U Jamb Lock Pillar Filler
p/n: 60-0570-79
This U Jamb Door Lock Pillar Filler pair is designed from the original part for superior fitment and sealing. This part seals the bottom of the rear side window. Fully molded authentic rubber construction with metal core.
Upper Control Arm Shaft
p/n: 20-1278-32
This three (3) piece Upper Control Arm Shaft set is designed from the original part for superior fitment and performance. Renew the performance of your aged and worn front suspension to restore the ride of your classic vintage vehicle.
Rear Window Gasket
p/n: 70-2051-81
This Rear Window Gasket is designed from the original part for superior fitment and seal. The seal mounts around the full perimeter of the back glass and has vulcanized, or bonded, ends which means no cutting or splicing is required for installation.
Rear Vent Window Division Post Weatherstrip
p/n: 70-3762-56
This Rear Door Vent Window Division Post Weatherstrip pair is designed from the original part for superior fitment and seal. This seal is fully molded with EPDM rubber over brass metal cores. This part fits opposite the glass run channel and seals the vent window when the vent is closed.
Trunk Weatherstrip - Clipped
p/n: 70-1123-85
This Clipped Trunk Weatherstrip is designed from the original part for superior fitment and seal. The seal mounts around the full perimeter and directly to the trunk lid using properly spaced plastic clips.
Windshield Gasket
p/n: 20-1321-50
This windshield gasket mounts around the full perimeter of the front glass and has properly molded corners for a precise, factory like fit. It also has the slot to accommodate the outer edge's decorative molding.
Fender Skirt Edge Weatherstrip
p/n: 70-0154-45
This Fender Skirt Edge Weatherstrip pair is designed from the original part for superior fitment, finish, and seal. This weatherstrips fits between the rear wheel fender skirt and the rear fender quarter panel.
Front Spring Bumpers
p/n: 60-0393-32
This Front Spring Bumper pair is a quality reproduction of the original factory part. These axle to frame bottoming rebound pads are dense rubber blocks that mount to the front axle.
Lower Tailgate Weatherstrip
p/n: 20-3142-85
This Lower Tailgate Weatherstrip is designed from the original part for superior fitment and seal. The weatherstrip mounts on the bottom of the tailgate.
Front Suspension Bumper
p/n: 70-1294-32
Bumper, front load rebound, upper.Width: 1.625 inches. Height: 2.75 inches.
Front Door Weatherstrips
p/n: 60-0299-72
This Front Door Weatherstrip pair is high-quality sponge rubber with inserted nylon clips. Designed from the original part for superior fitment and seal. Each strip is approximately one hundred sixty-six (166) inches long.
Fender Skirt Edge Weatherstrip
p/n: 25-0092-44
This Fender Skirt Edge Weatherstrip pair is designed from the original part for superior fitment, finish, and seal. This weatherstrips fits between the rear wheel fender skirt and the rear fender quarter panel.
Beltline Weatherstrip
p/n: 30-0301-57
Window felt inner and/or outer. Flexible, pile lined, rubber covered, with stainless bead. Available in 3ft pair.
Stabilizer Bushing
p/n: 70-0627-33
Bushings, stabilizer bar, front. Fully molded rubber. One and three fourths inch (1 3/4") length by one and one half inch (1 1/2") width by three fourths inch (3/4") inside hole diameter by one and five eighths inch (1 5/8") height.
Axle Rebound Pad
p/n: 70-1289-32
Bushing, rear support arm. Rear upper. Four (4) per car. For lower see #70-1290-32.
Axle Rebound Pad
p/n: 70-1290-32
Bushing, rear support arm. Rear lower. Four (4) per car. For upper see #70-1289-32.
Rear Axle Bumpers
p/n: 70-0210-32
This Rear Axle Bumper pair is a quality reproduction of the original factory part. These bottoming pads are dense rubber blocks that mount by bracket to the rear axle tube.