Metal Sleeved Grommet
p/n: 70-0203-41
Flanged rubber grommet with metal sleeve bushing. Used as part of the accelerator relay lever. Also used from 1959-61 on all Cadillac models as a bushing for the windshield wiper relay lever adaptor.
Upper Radiator Filler
p/n: 70-2784-45
This single piece Upper Radiator Filler is designed from the original part for superior fitment and function. This upper radiator to core support filler piece is die cut from quality masticated rubber to authentic original dimensions.
Body Mount Isolator Pad
p/n: 70-0929-48
Body Mount Isolator Pad - Rubber with metal core and locating collar as original part. Part dimensions = Two and three sixteenths inch (2 3/16") square by one inch (1") overall height with thirteen sixteenths inch (13/16") inside bolt diameter. Does not include any fastener hardware.
Lower Rear Engine Mount
p/n: 20-0584-11
This Lower Rear Engine Mount is designed from original part for correct fitment and function. Made of a quality dense rubber for durability and proper engine vibration isolation. Two (2) required per truck.
Door Handle Gasket Set
p/n: 70-0925-69
This Door Handle Gasket Set is designed from the original part for superior fitment and seal. This six (6) piece gasket set will do two (2) doors.
Body Mounting Pad
p/n: 70-1749-48
This Body Mounting Pad is fully molded rubber with a metal core and locating collar. These frame pads are installed between the frame and the floor pans.
Front Lower Engine Mount
p/n: 20-0596-11
This Front Lower Engine Mount is designed from original part for correct fitment and function. Rubber coated over a metal core for durability and proper engine vibration isolation.
1-7/16" Firewall Grommet
p/n: 60-0276-45
This Firewall Grommet is used to run the throttle rod and tube, oil pressure gauge pipe, heat indicator tube, and choke rod through the firewall.
Header Bow Weatherstrip - Hardtop
p/n: 70-3918-64
This Header Bow Weatherstrip is the top and front seal rubber across windshield header for removable hardtops. Fully molded with the proper, as original, cross section in top quality rubber.
Door Weatherstrip
p/n: 70-1650-70
Seal, rear door at rear of window.Length: 1.75 inches. Width: .875 inches.
Tailgate weatherstrip
p/n: 20-1526-87
Weatherstrip, tailgate lower glass sash channel. Goes between glass and channel.
Taillight Lens Gaskets - In Fin
p/n: 70-3117-15
This Taillight Lens Gasket pair is designed from the original part for superior fitment and seal. This reproduction gasket fits between the taillight lens & taillight housing in fin.
Radiator top seal
p/n: 20-0130-31
Seal, radiator support top to hood. Includes special plastic buttons to install. For models with A/C.
Body Mounting Pad
p/n: 50-0506-48
Pad, body mounting. Rubber with metal core, locating collar and metal sleeve as original. Metal sleeve is removable.
Taillight & Back Up Light Lens Gasket Set
p/n: 70-3310-15
This six (6) piece Taillight Lens and Back Up Light Lens Gasket set is designed from the original part for superior fitment and seal. These reproduction gaskets fit between taillight / back up light lens and housing.
Brake Master Cylinder Push Rod Boot
p/n: 60-0180-24
This Brake Master Cylinder Push Rod Boot is made from high-quality Nitrile rubber for a precise, factory like fit for your classic vehicle. Manufactured to OEM specifications to install for an authentic fit and finish.
Trunk Weatherstrip
p/n: 70-3923-84
This Trunk Weatherstrip is made from top quality rubber to ensure durability and designed from the original part for a superior fitment and seal. The seal mounts around the full perimeter of the trunk and directly to the body.
Quarter Window Vertical Leading Edge
p/n: 70-0141-58
This quarter to side window Vertical Leading Edge Weatherstrip pair is designed from the original part for superior fitment and seal. Slides into metal retaining channel attached to rear side window and seals between the front door window and the rear quarter window.
Battery Clamp Cover
p/n: 70-0095-21
This Battery Clamp Cover helps to protect the nearby metal and finish. Fully molded from high-quality EPDM rubber to ensure durability. Good copy from an original part.
Hood To Fender Bumper Set
p/n: 20-0033-42
This four (4) piece Hood to Fender Bumper Set is a quality reproduction of the original factory part. This rubber bumper attaches to the front fender to support / cushion the hood closure.
Rocker Panel Inner Drain Cover
p/n: 70-2392-45
This Rocker Panel Inner Drain Cover pair is designed from the original part for superior fitment and seal. Fully molded with proper attaching teeth and flap.
Radiator Support To Hood Weatherstrip
p/n: 20-1452-42
This Radiator Support To Hood Weatherstrip is designed from the original part for superior fitment and seal. Includes staples to install. This weatherstrip works to seal the hood to the radiator support for better engine cooling.
Hood Bumper
p/n: 20-0014-42
Bumpers, hood front to radiator support. Five sixteenths (5/16) inch by twenty four (24) thread.
Splash Apron / A-Arm Dust Shield Filler
p/n: 70-3068-45
This two (2) piece Splash Apron / A-Arm Dust Shield Filler pair is designed from the original part for superior fitment and seal. Filler pieces are die cut from quality masticated rubber to authentic original dimensions. Left and Right pieces fit over suspension a-arms and inside front inner fenders.
Steering Column Floorplate
p/n: 20-1694-88
Seal, steering column tube. Installs on top of floor mat.
Spring Clamp Liner Set
p/n: 20-1272-32
Six (6) piece Spring Clamp Liner Set. The front spring takes eight pieces for both sides and the rear spring takes four pieces for both sides.
Fender Anti-Squeak Weatherstrip
p/n: 20-1864-45
This Fender Anti-Squeak Weatherstrip mounts between the front fender splash apron and the front fender. The weatherstrip is an exact reproduction of the original Ford part. Sold as a seventy-two (72") inch strip.
Rear Upper Engine Mount
p/n: 60-0463-11
This Rear Upper Engine Mount is designed from original part for correct fitment and function. Made of a high-quality EPDM dense rubber for durability and proper engine vibration isolation.
Parking and Fog Light Lens Gaskets
p/n: 70-3159-16
This Parking and Fog Light Lens Gasket pair is designed from the original part for superior fitment and seal. This reproduction gasket fits between the Parking and Fog Light Lens and the Parking and Fog Light Housing or Bezel.
Front Suspension Bumper
p/n: 20-0034-32
Bumper, front suspension upper arm. Three eighths (3/8) inch by three fourths (3/4) inch bolt, twenty four (24) threads.
Cowl Vent Gasket
p/n: 60-0601-54
Side cowl vent seal. One eighth (1/8) inch thick high quality sponge design.Length: 8.50 inches. Width: 5.375 inches.
Body Mounting Pad
p/n: 70-2165-48
Pad, body mount, lower bolt retaining. Rubber with metal washer molded in. Used on the bottom of most mounting locations.
Cowl Drain Gutter Hose Grommet
p/n: 33-0329-54
This Cowl Drain Gutter Hose Grommet is fully molded and designed from the original part for superior fitment and seal. This grommet is made from high-quality EPDM dense rubber to provide excellent durability.
Decklid Top Cover Weatherstrip
p/n: 70-3922-67
This Decklid Top Cover Weatherstrip is designed from the original part for a superior fitment and seal. This seal mounts around the full perimeter of the soft top storage compartment.
Rear Bumper To Fender Filler
p/n: 70-2501-45
This Rear Bumper To Fender Filler pair is designed from the original part for superior fitment and function. Filler pieces are die cut from quality masticated rubber to authentic original dimensions. These filler pieces fit behind each bumper end of the vehicle.