Lower Engine Mount
p/n: 20-0597-11
This Lower Engine Mount is designed from original part for correct fitment and function. Rubber coated over a metal core for durability and proper engine vibration isolation.
Upper Engine Mount
p/n: 20-0598-11
This Upper Engine Mount is designed from original part for correct fitment and function. Rubber coated over a metal core for durability and proper engine vibration isolation.
Body Mount Isolator Pad
p/n: 70-0929-48
Body Mount Isolator Pad - Rubber with metal core and locating collar as original part. Part dimensions = Two and three sixteenths inch (2 3/16") square by one inch (1") overall height with thirteen sixteenths inch (13/16") inside bolt diameter. Does not include any fastener hardware.
Door Handle Gasket Set
p/n: 70-0925-69
This Door Handle Gasket Set is designed from the original part for superior fitment and seal. This six (6) piece gasket set will do two (2) doors.
Body Mounting Pad
p/n: 70-1749-48
This Body Mounting Pad is fully molded rubber with a metal core and locating collar. These frame pads are installed between the frame and the floor pans.
1-7/16" Firewall Grommet
p/n: 60-0276-45
This Firewall Grommet is used to run the throttle rod and tube, oil pressure gauge pipe, heat indicator tube, and choke rod through the firewall.
Door Handle Gasket Set
p/n: 70-0771-69
This Door Handle Gasket Set is designed from the original part for superior fitment and seal. This six (6) piece gasket set will do two (2) doors.
Front Lower Engine Mount
p/n: 20-0596-11
This Front Lower Engine Mount is designed from original part for correct fitment and function. Rubber coated over a metal core for durability and proper engine vibration isolation.
Header Bow Weatherstrip - Hardtop
p/n: 70-3918-64
This Header Bow Weatherstrip is the top and front seal rubber across windshield header for removable hardtops. Fully molded with the proper, as original, cross section in top quality rubber.
Fuel Filler Neck Grommet
p/n: 70-1439-39
This Fuel Filler Neck Grommet is designed from the original part for superior fitment and seal. This grommet fits around the vehicles fuel filler neck between the filler neck and vehicle body. Fits as original.
Radiator top seal
p/n: 20-0130-31
Seal, radiator support top to hood. Includes special plastic buttons to install. For models with A/C.
Tailgate weatherstrip
p/n: 20-1526-87
Weatherstrip, tailgate lower glass sash channel. Goes between glass and channel.
Body Mounting Pad
p/n: 50-0506-48
Pad, body mounting. Rubber with metal core, locating collar and metal sleeve as original. Metal sleeve is removable.
Brake Master Cylinder Push Rod Boot
p/n: 60-0180-24
This Brake Master Cylinder Push Rod Boot is made from high-quality Nitrile rubber for a precise, factory like fit for your classic vehicle. Manufactured to OEM specifications to install for an authentic fit and finish.
Stabilizer Bar End Link Set
p/n: 60-0221-33
Twenty-two (22) piece Stabilizer Bar End Link set for both sides of one (1) vehicle, fits front or rear bar. Order two (2) sets for vehicles with front and rear stabilizer bars. Hex head bolt 3/8"-16 NF x 6-15/16" long. Comes with metal sleeve, metal cup washers and rubber grommets.
Trunk Weatherstrip
p/n: 70-3923-84
This Trunk Weatherstrip is made from top quality rubber to ensure durability and designed from the original part for a superior fitment and seal. The seal mounts around the full perimeter of the trunk and directly to the body.
Battery Clamp Cover
p/n: 70-0095-21
This Battery Clamp Cover helps to protect the nearby metal and finish. Fully molded from high-quality EPDM rubber to ensure durability. Good copy from an original part.
Hood Bumper
p/n: 20-0014-42
Bumpers, hood front to radiator support. Five sixteenths (5/16) inch by twenty four (24) thread.
Radiator Support To Hood Weatherstrip
p/n: 20-1452-42
This Radiator Support To Hood Weatherstrip is designed from the original part for superior fitment and seal. Includes staples to install. This weatherstrip works to seal the hood to the radiator support for better engine cooling.
Rocker Panel Inner Drain Cover
p/n: 70-2392-45
This Rocker Panel Inner Drain Cover pair is designed from the original part for superior fitment and seal. Fully molded with proper attaching teeth and flap.
Taillight Lens Gaskets
p/n: 70-3775-15
This Taillight Lens Gasket pair is designed from the original part for superior fitment and seal. These reproduction gaskets fit between taillight lens & taillight housing.
Spring Clamp Liner Set
p/n: 20-1272-32
Six (6) piece Spring Clamp Liner Set. The front spring takes eight pieces for both sides and the rear spring takes four pieces for both sides.
Splash Apron / A-Arm Dust Shield
p/n: 70-2801-45
This two (2) piece Splash Apron / A-Arm Dust Shield Filler set is designed from the original part for superior fitment and seal. Filler pieces are die cut from quality masticated rubber to authentic original dimensions. Pieces fit over suspension a-arms and inside front inner fenders.
Radiator Side Seals
p/n: 70-3990-31
This Radiator Side Seal pair is designed from the original part for superior fitment and function. Left and Right seals are die cut from quality masticated rubber to authentic original dimensions.
Rear Upper Engine Mount
p/n: 60-0463-11
This Rear Upper Engine Mount is designed from original part for correct fitment and function. Made of a high-quality EPDM dense rubber for durability and proper engine vibration isolation.
Steering Column To Floor Seal
p/n: 20-0674-36
This Steering Column To Floor Seal is designed from the original part for superior fitment and sealing. Seal part is die cut from quality rubber to authentic original dimensions. This part fits around the steering column to seal the column through the body floor pan.
Front Suspension Bumper
p/n: 20-0034-32
Bumper, front suspension upper arm. Three eighths (3/8) inch by three fourths (3/4) inch bolt, twenty four (24) threads.
Taillight Assembly Mounting Pads
p/n: 70-3777-15
This Taillight Assembly Mounting Pad pair is designed from the original part for superior fitment and seal. These reproduction gaskets fit between the taillight assembly and the vehicle body.
Cowl Vent Gasket
p/n: 60-0601-54
Side cowl vent seal. One eighth (1/8) inch thick high quality sponge design.Length: 8.50 inches. Width: 5.375 inches.
Directional or Back Up Light Lens Gaskets
p/n: 70-3776-16
This Directional Turn Signal or Back Up Light Lens Gasket pair is designed from the original part for superior fitment and seal. This reproduction gasket fits between the Light Lens and the Light Housing or Bezel.
Body Mounting Pad
p/n: 70-2165-48
Pad, body mount, lower bolt retaining. Rubber with metal washer molded in. Used on the bottom of most mounting locations.
Decklid Top Cover Weatherstrip
p/n: 70-3922-67
This Decklid Top Cover Weatherstrip is designed from the original part for a superior fitment and seal. This seal mounts around the full perimeter of the soft top storage compartment.
Taillight Lens Gaskets
p/n: 70-3235-15
This Taillight Lens Gasket pair is designed from the original part for superior fitment and seal. This reproduction gasket fits between taillight lens & taillight housing.
Vent Window Rebuild Set
p/n: 70-4801-70
This Vent Window Rebuild Set includes glass setting tape (1/16 thick), hinge pivot step rivet pair, and a rivet peening punch. The set has enough materials for both the passenger side and driver side vent window assemblies.
Directional and Parking Light Lens Gaskets
p/n: 70-3115-16
This Turn Signal and Parking Light Lens Gasket pair is designed from the original part for superior fitment and seal. This reproduction gasket fits between the Signal / Parking Light Lens and the Signal / Parking Light Housing or Bezel.
Door Handle Gasket Set
p/n: 50-0560-69
This Door Handle Gasket Set is designed from the original part for superior fitment and seal. This four (4) piece gasket set will do two (2) doors.
Hood to Cowl Weatherstrip
p/n: 70-3959-43
This Hood To Cowl Weatherstrip has the proper rubber cross section and made from top quality rubber to ensure durability. Designed from the original part for a superior fitment and seal.
Rear Bumper Trim Welts
p/n: 70-4092-45
This pair of Quarter Panel to Rear Bumper End Trim Welts are designed from the originals for superior fitment and seal. These welt strips mount to the rear quarter panel bumper end piece, with one per vehicle side.
Rear Seat Back Finish Panel to Package Tray Weatherstrip
p/n: 70-4096-87
This Rear Seat Back Finish Panel To Package Tray Weatherstrip mounts directly to the body to seal the Rear Seat Back Finish Panel to the Package Tray.
Window Stop Stem Bumper
p/n: 33-0675-62
Cushion (stem bumper), window stop, lower. For front and rear door, rear side and quarter windows as required.
Hood Bumper
p/n: 70-0770-42
Bumper, fender to hood. Correct detail with ridges as original. Four (4) required per car.Length: 1.3125 inches.
Window Regulator | Accelerator Rod Seal
p/n: 60-0652-70
This Window Regular | Accelerator Rod Seal is used as a front window regulator seal for 1955-60 passenger cars with electric windows and for 1957-62 Corvette models. Used as an accelerator rod through toeboard seal for 1955-62 V8 only Corvettes.
Glovebox Door Check Grommet
p/n: 27-0105-88
This Glovebox Door Check Grommet is manufactured out of 100% EPDM dense rubber for durability. Designed from original for a proper fit.
Rear Lower Engine Mount
p/n: 60-0459-11
This Rear Lower Engine Mount is designed from original part for correct fitment and function. The mount is made from a dense rubber for durability and proper engine vibration isolation.
Back Up Light Lens Gaskets
p/n: 70-3234-17
This Back Up Light Lens Gasket pair is designed from the original part for superior fitment and seal. This reproduction gasket fits between the back-up light lens and the back-up light housing or light bezel.
Taillight Lens Gaskets - In Fin
p/n: 70-3502-15
This Taillight Lens Gasket pair is designed from the original part for superior fitment and seal. These reproduction gaskets fit between the taillight lens & taillight housing in fin.
Beltline Guide Plate - Plastic
p/n: 50-0384-62
This Beltline Guide Plate is designed from the original part for superior fitment and function. High quality plastic plate attaches to various outer beltline window scraper weatherstrips.
Exhaust Tailpipe Hanger Strap
p/n: 60-0308-13
This Exhaust Tailpipe Hanger Strap is made from high-quality rubber for a precise, factory like fit for your classic vehicle. Muffler/tailpipe system, reproduction strap type is manufactured to OEM specifications.
Front Door Lock Pillar Filler
p/n: 70-0834-79
This Front Door Lock Pillar Filler pair is designed from the original part for superior fitment and sealing. This left and right weatherstrip filler seals the bottom at the front of the rear side window. Also known as a door jamb seal.
Hood bumper
p/n: 20-0041-42
Bumpers, rear of hood to top of fender. Two (2) required per vehicle.Ford Cars 1961-64 Bumpers, rear of hood to top of fender. Requires 2 pair for hood.
Tie Rod Dust Covers
p/n: 20-2484-36
This Tie Rod Dust Cover, drag link seal, is sold as a four (4) piece set. The seals are designed from originals for proper fitment.
Hood Bumper
p/n: 25-0076-42
This Hood Bumper is a quality reproduction of the original factory part. These rubber bumpers attach to the front fender to support / cushion the hood closure. Six (6) required per car.
Taillight Gasket
p/n: 60-0697-15
Seal, taillight bezel. Correct profile and long lasting material. Four (4) strips cut sixteen and three eighths (16-3/8) inches long.
Hood Bumper
p/n: 27-0098-42
Bumper, hood front to radiator ledge, adjustable. Includes plated bolt and rubber cushion.Length: 2.1875 inches.
Front Stabilizer Bar End Link Set
p/n: 20-0037-33
This eleven (11) piece Front Stabilizer Bar End Link Set is designed from original parts so it fits correctly. Two (2) kits / sets required per car as one (1) kit / set services one side of front stabilizer bar.
Fuel Filler Neck Grommet
p/n: 20-0585-39
This Fuel Filler Neck Grommet is designed from the original part for superior fitment and seal. This grommet fits around the vehicles fuel filler neck between the filler neck and vehicle body.
Hood Bumper
p/n: 70-0907-42
Bumper, hood front aligning. Correct design with proper screw thread.Height: 2.50 inches.
Transmission Mount
p/n: 70-2058-25
This Transmission Mount is a new aftermarket replacement mount manufactured to meet or exceed factory specifications.. One (1) required per vehicle.
Accelerator Pedal Rod Grommet
p/n: 20-0044-41
This Accelerator Pedal Rod Grommet is used to wrap around the accelerator rod at the firewall. Designed from the original part for superior fit and seal.
Clutch or Brake Pedal Pad
p/n: 20-0848-22
This reproduction Clutch and/or Brake Pedal Pad slips over the full perimeter of the pedal for a precise, factory fit. A perfect reproduction to replace worn original pedal pads. Manufactured in quality black rubber.