Engine Mount
p/n: 20-1978-11
This Engine Mount is designed from the original part for superior fitment and function. This engine mount works to absorb and isolate engine and driveline vibrations. The set services one mount. 1937-1941 require four (4) sets for both Front and Rear. 1942-1948 require two (2) sets.
Side Mount Cover Pad
p/n: 70-0077-37
Pads, channel type, for sidemount covers. Eight (8) piece set.Width: .25 inches. Height: .6875 inches.
Battery Carrier Edge Liner
p/n: 60-0112-21
Edge liner, battery carrier cover.Length: 42.0 inches. Width: .25 inches. Height: .6875 inches.
License Light Mounting Pad
p/n: 40-0174-17
Pad, license light mounting. Plain type without edge bead as original.Length: 8.0 inches. Width: 3.25 inches.
Gearshift Boot
p/n: 50-0035-24
Boot, gearshift. Black rubber. For brown see our #50-0035-89.Width: 2.8125 inches.
Fender Welting
p/n: 20-1590-44
This black Fender Welting is designed from the original part for superior fitment and seal. This welting material fits between the fenders and the vehicle body. Thirty (30) foot roll.
Gearshift Seal
p/n: 60-0471-24
This Gearshift Seal is designed from the original part for superior fitment and function. For the gearshift at floor.
Flexible Run Channel - 30 Inch Pair
p/n: 40-0309-57
Channel, side window glass, vertical run. Flexible, felt lined, rubber covered channel. Available in 30" pair.
Horn Button Contact Ring
p/n: 60-0157-21
Ring, horn button contact. Accessory banjo steering wheel. Four and one eighth (4-1/8) inch outside diameter.
Firewall Grommet Set
p/n: 50-0048-20
This Firewall Grommet Set contains two (2) pieces including one (1) round grommet for temperature and oil pressure lines and one (1) oval grommet for vacuum lines, throttle, choke, and speedometer cables.
Shock Absorber Bushing
p/n: 30-0024-33
Bushings, rear shock link assembly. Designed to act like sleeve inside link arm.Height: .9375 inches.
Horn Button Contact Cushion
p/n: 60-0192-21
Cushion, standard steering wheel horn button contact. Two and one half (2-1/2) inch diameter.
Fuel Filler Neck Grommet
p/n: 60-0022-41
This Fuel Filler Neck Grommet is fully molded rubber and slightly angled. Three and eleven sixteenths inch (3-11/16") outside diameter by two and three sixteenths inch (2-3/16") top hole diameter by two and five eighths inch (2-5/8") bottom hole diameter.
Brake and Clutch Shank Seal
p/n: 30-0055-24
Seals, brake and clutch pedal shanks, against underside of floorboard.Length: 2.5625 inches. Width: 1.75 inches.
Brake and Clutch Pedal Bumper
p/n: 60-0024-24
Bumpers, brake and clutch pedal shank to floorboard. Rides pedal shank under floorboard.
Rear Engine Mount
p/n: 70-0648-11
This Rear Engine Mount is used as an upper and lower support bracket at the transmission. Made from high-quality EPDM rubber for a precise, factory like fit.
Radio Antenna End Loop
p/n: 70-0105-21
End loop, radio antenna. Cord reinforced rubber with metal grommet. Mounted on running board on some models.
Brake and Clutch Shank Seal
p/n: 40-0175-24
Seal, brake and clutch pedal shank to floorboard. One and one half (1-1/2) inch by two and one eighth (2-1/8) inch by three fourths (3/4) inch thick.
Trunk Hinge Mounting Pad
p/n: 50-0372-87
Pad, trunk hinge. Non-bead cushion like original. Four (4) piece set.Length: 7.125 inches.