Door Handle Gasket
p/n: 30-0242-71
Pads, door handle escutcheon plate, front and rear doors.Length: 2.625 inches.
Door Alignment Pad
p/n: 70-1821-71
Wedge pads, door aligning.Length: 1.125 inches. Width: .5 inches. Height: .875 inches.
Vacuum Cylinder Seal
p/n: 30-0203-24
Seals, actuating valve rod, brake and clutch vacuum cylinder.Width: .875 inches.
Glovebox Door Check Grommet
p/n: 70-0285-88
Grommet, glovebox door check link, for one and one eighth (1-1/8) inches slot in dash.Length: 1.4375 inches. Width: .625 inches.
Starter Pedal Button Cover
p/n: 60-0166-21
This Starter Button Pedal Cover is designed from the original part for an authentic fit, finish, and appearance. Rubber slip over type for old metal. Two (2") inch outside diameter.
Taillight Mounting Pad
p/n: 60-0259-15
Pad, taillight bracket mounting. Two and five sixteenths (2-5/16) inch by three and three eighths (3-3/8) inch, inside bead. Length: 3.6875 inches.
Door Bumper
p/n: 30-0128-71
Pad, door jamb (Atwood type), one and five eighths (1-5/8) inch long.Width: 1.5625 inches. Height: 1.375 inches.
Body Mounting Pad
p/n: 60-0028-48
Pad, front body mounting. Right angle style. Fully molded rubber. Four and one sixteenth inch (4 1/16") length by three and seven eighths inch (3 7/8") width by one half inch (1/2") inside hole diameters by one fourth inch (1/4") height.
Steering Column Cushion - Brown
p/n: 60-0012-89
This Steering Column Cushion grommet is designed from the original part for an authentic fit, finish, and appearance. For the steering column to cowl U-bolt clamp. Brown rubber. For Black see 60-0012-36
Steering Column Cushion
p/n: 40-0259-36
Pad, steering post bracket. One (1) per car. Cushions steering post clamp to instrument panel.Length: 3.50 inches.
Brake Master Cylinder Push Rod Boot
p/n: 60-0180-24
This Brake Master Cylinder Push Rod Boot is made from high-quality Nitrile rubber for a precise, factory like fit for your classic vehicle. Manufactured to OEM specifications to install for an authentic fit and finish.
Shock and Sway Bar Grommet
p/n: 30-0193-33
Grommet, rear shock arm link (lower end), or rear sway bar link lower end. Shock arms used four (4) per car. If needed, sway bar used two (2) per car. Fully molded rubber.
Wheel cover cushion
p/n: 70-1024-38
Cushion, wheel disk. A fully molded alternative to our #70-0094-38.
Door Bumper
p/n: 17-0039-71
Bumper, round door side. An auxiliary door side bumper on door jamb pad.
Steering Column Cushion - Black
p/n: 60-0012-36
This Steering Column Cushion grommet is designed from the original part for an authentic fit, finish, and appearance. For the steering column to cowl U-bolt clamp. Black rubber. For Brown see 60-0012-89.
Battery Clamp Cover
p/n: 70-0095-21
This Battery Clamp Cover helps to protect the nearby metal and finish. Fully molded from high-quality EPDM rubber to ensure durability. Good copy from an original part.
Door Bumper
p/n: 17-0040-71
Bumper, oblong, door side. An auxiliary door jamb or side bumper.Width: 1.75 inches. Height: .75 inches.
Clutch Pedal Bumper - Under Floorboard
p/n: 60-0355-24
This Clutch Pedal Bumper is designed from the original part for superior fitment and function. This clutch pedal shank bumper fits under vehicle floorboard.
Hood Support Rod Top Cap
p/n: 40-0346-42
Pad, hood rest rod. For five sixteenths (5/16) inch diameter hood support rod. Also see our #40-0103-42.Length: 1.0 inches.
Firewall to Hood Cowl Lacing
p/n: 20-0352-42
A cloth Firewall to Hood Cowl Lacing measuring approximately ninety (90") inches in length and complete with mounting screws. Designed from the original part for superior fitment, finish and function.
Hood Support Rod Top Cap
p/n: 40-0103-42
Top cap, hood support rod. For seven sixteenths (7/16) inch diameter rod. Also see our #40-0346-42.Length: 1.0 inches.
Body Mounting Pad
p/n: 40-0232-48
Pad, body mounting, upper. Fully molded rubber with locating collar. As many as twelve (12) used per car. One and fifteen sixteenths inch (1 15/16") outside width by two inch (2") outside width. See drawing for more dimensions.
Spring or Stabilizer Bushing
p/n: 11-0020-35
Bushing, spring bracket on frame (Auburn and Cord 810 & 812). Also used as a grommet, front stabilizer bar (Graham models 116 & 120). Fully molded rubber.
Steering Column Gasket
p/n: 60-0014-36
This Steering Column to Toe Board Gasket is designed from the original part for superior fitment and sealing. This part fits around the steering column to seal the column through the body floor pan.
Quarter Window Weatherstrips
p/n: 20-2122-77
This Quarter Window Weatherstrip is designed from the original part for superior fitment and seal. This seal mounts around the full perimeter of the left and right rear quarter glass for a precise, factory fit. Ends are not bonded. For stationary windows only.
Firewall to Hood Weatherstrip - Cowl Lacing
p/n: 20-2184-42
This Firewall to Hood Cowl Lacing Weatherstrip is designed from the original part for superior fitment and seal. An exact reproduction of the original profile. This forty-four (44") inch weatherstrip installs at the rear of the engine bay to seal between the hood and the vehicle firewall.
Lower Door Weatherstrip
p/n: 20-2249-73
This Lower Door Weatherstrip is designed from the original part for superior fitment and seal. These door weatherstrips mount (glue-on) directly to the left or right doors sealing the bottom of the door when closed.
Front Axle Bumper
p/n: 20-2007-32
This Front Axle Bumper is designed from the original part for superior fitment and function. Bumper is manufactured with top quality materials for good durability.
Lower Door Weatherstrips
p/n: 20-0391-73
This Lower Door Weatherstrip pair is designed from the original part for superior fitment and seal. These secondary door weatherstrips mount in channels on the cab body at the lower door opening. Works to seal the bottom of the doors against the vehicle body when the door is closed.
Channel Filler Weatherstrip
p/n: 20-2091-62
This Channel Filler Weatherstrip is designed from the original part for superior fitment and seal. This door glass to body filler seal fits in the metal channel that holds the glass piece. Sold in a 36" strips.
Door Bumper
p/n: 30-0002-71
Bumper, door side. One and one fourth (1-1/4) inch by two (2) inch.Length: 2.0 inches. Width: 1.25 inches.
Engine Mount Pad
p/n: 11-0028-11
This Engine Mount Pad is designed to original pattern with superior workmanship. Made of a high-quality EPDM dense rubber for durability and authentic fit.
Channel Filler Weatherstrip
p/n: 20-1633-62
Seal, door glass and stainless frame special. Top, bottom, and sides for one door.Width: .375 inches. Height: .625 inches.
Exhaust Support Grommet
p/n: 60-0031-13
This Exhaust Support Grommet is designed from the original part for superior fitment and usage. The OEM direct fit application is as a rear and middle muffler exhaust support hanger.
2" Firewall Grommet
p/n: 70-0158-21
This Firewall Grommet is used to run the ignition switch conduit through the firewall. Designed from original parts for excellent workmanship.
Coil wire sleeve
p/n: 40-0336-21
Nipple, sparkplug wire at sparkplug, for right angle plug terminal. This is an exact copy of the style used at the time. Not a modernistic makeover.
Door Handle Ferrule
p/n: 70-0111-69
A Ferrule for three fourths (3/4") inch outside door handles. Chrome plated brass. Used for outside door handle or outside trunk handle.
1-11/16" Firewall Grommet
p/n: 32-0196-21
This Firewall Grommet is fully molded and designed from the original part for superior fitment and seal. This grommet is made from high-quality EPDM dense rubber to provide excellent durability.
2-1/2" Black Bow Drill Cloth Tape
p/n: 70-1172-65
This Bow Drill Cloth Tape is used for covering convertible side window weatherstrip. Black in color and available in a five (5) foot roll.
Body Mounting Pad
p/n: 50-0231-48
Shim, body sill. Fully molded rectangular rubber. A total of six (6) are needed per car.
Windshield Wiper Transmission Gaskets
p/n: 70-1196-53
This Windshield Wiper Transmission Gasket pair is designed from the original part for superior fitment and function. This gasket mounts between the windshield wiper transmission and the vehicle body work to reduce noise and vibration.
Spark plug retaining ring
p/n: 30-0352-21
Retaining ring, spark plug wire. Two (2) per car.Chevrolet 1935-48 Retaining ring, spark plug wire. Two (2) per car. All models.
Body Mounting Pad
p/n: 70-0235-48
Pad, body mounting. Fully molded rubber with locating collar. Rectangular shaped.
1-1/2" Firewall Grommet
p/n: 50-0299-20
This Firewall Grommet is used to run the oil pressure and water temperature lines through the firewall. Designed from original part for excellent workmanship.
Engine Mount Pad
p/n: 11-0029-11
This Engine Mount Pad is designed to original pattern with superior workmanship. Made of a high-quality EPDM dense rubber for durability and authentic fit.
Horn Button Contact Cushion
p/n: 18-0027-21
Cushions, horn contact plate.Qty Required:3 Width: 1.0 inches.
2-1/2" Tan Bow Drill Cloth Tape
p/n: 70-1173-65
This Bow Drill Cloth Tape is used for covering convertible side window weatherstrip. Tan in color and available in a five (5) foot roll.
Wiper Transmission Gasket
p/n: 70-1197-53
Gasket, windshield wiper transmission. Replaces #4074294 & #4082366.
Gearshift Knob
p/n: 20-0583-24
This black floor shift lever Gearshift Knob is designed from the original part for a superior fit and finish. This reproduction part is a direct screw on replacement for that broken, aged-out original knob.
Front Bumper Gravel Shield
p/n: 70-0127-30
This anti-rattle Front Bumper Gravel Shield pad is designed from the original part for superior fitment and seal. Fully molded with top quality EPDM rubber over a corrosion resistant brass core to ensure durability, fit and appearance.
Door Bumper Pad
p/n: 30-0032-71
This circular shaped Door Bumper Pad is designed from the original part for an authentic fit, finish, and appearance.
Door Check Link Rod End Stop
p/n: 70-0326-70
End stop and pad, door check link rod. Rubber with embedded steel plate, five sixteenths (5/16) inch diameter thread. Most models with rod type door checks.
Tie Rod Dust Covers
p/n: 20-2484-36
This Tie Rod Dust Cover, drag link seal, is sold as a four (4) piece set. The seals are designed from originals for proper fitment.
Door Check Link Rod End Stop
p/n: 20-1640-70
This Door Check Link Rod End Stop is designed from the original part for superior fit and function. This door stop fits between the door and body to limit the swing opening of the door preventing overtravel. Door check arm and bumper. Enough for one door.
Body Mounting Pad
p/n: 50-0232-48
Shim, body sill, for #3, #5, and #7 body bolts. Six (6) per car. Width: 2.0 inches. Height: 2.0 inches.
Body Mounting Pad
p/n: 60-0027-48
Pad, side body mounting. Fully molded rubber, rectangular. Two and seven-sixteenths inch (2-7/16") outside length by one and five-eights inch (1-5/8") outside width by one-fourth inch (1/4") height.
Door Bumper
p/n: 40-0037-70
Pad, door jamb. One and nine sixteenths (1-9/16) inch long by one and one eighth (1-1/8) inch wide.Length: 1.625 inches. Width: 1.0625 inches.
2" Spare Wheel Carrier Grommet
p/n: 32-0355-37
This Spare Wheel Carrier Grommet is fully molded and designed from the original part for superior fitment and seal. This grommet is made from high-quality EPDM dense rubber. Designed for the rear wheel carrier bracket base.
Body Mounting Pad
p/n: 40-0231-48
Pad, body mounting, upper. Fully molded rubber with locating collar. One and fifteen sixteenths inch (1 15/16") outside diameter by three fourths inch (3/4") locating collar outside diameter by one half inch (1/2") inside locating hole diameter.
Stabilizer Grommet
p/n: 70-0436-33
Grommet, front stabilizer bar link or rear shock link to axle. Fully molded rubber. Eight (8) required per car.
Shock or Stabilizer Link Cross Pin Bushing
p/n: 50-0220-32
This Shock or Stabilizer Link Cross Pin Bushing is designed from the original part for superior fitment and function. A rubber bushing for shock absorber link cross pin or stabilizer cross link pin.
Vent Window Division Post Weatherstrip
p/n: 70-0040-56
This Vent Window Division Post Weatherstrip is an extruded thirty (30") inch rubber strip that may have to be glued to your old original division post seal core, or directly to the division post.
Firewall Grommet
p/n: 27-0026-20
This Firewall Grommet is used to run the control cables, tubes, and wires through the firewall. The two (2) hole type fits a three fourths (3/4) inch by one and five sixteenths (1-5/16) inch hole.
Shock and Sway Bar Bushing
p/n: 11-0016-33
Bushing, various uses. Fully molded rubber. One and one fourth inch (1 1/4") outside diameter by one half inch (1/2") inside hole diameter by three fourths inch (3/4") height. Shocks: 8 per car. Sway bar: 4 per car.
Engine Mount Pad
p/n: 11-0027-11
This Engine Mount Pad is designed to original pattern with superior workmanship. Made of a high-quality EPDM dense rubber for durability and authentic fit.
Door and Trunk Handle Gasket
p/n: 30-0235-71
Pad, outside door handle escutcheon.Length: 2.4375 inches.
Dimmer Switch Grommet
p/n: 40-0083-88
This Dimmer Switch Grommet is used during carpet installations in automotive restorations. Made from high-quality EPDM dense rubber to provide excellent durability. Includes a wide flange for floor dimmer switch fitments.
Body Mounting Pad
p/n: 40-0230-48
Pad, body mounting, lower. Fully molded rubber. One and eleven sixteenths inch (1 11/16") outside diameter by nine sixteenths inch (9/16") inside hole diameter by one half inch (1/2") height.
Door and Trunk Handle Gasket
p/n: 40-0132-70
Pad, door handle escutcheon. Two and five sixteenths (2-5/16) inch by one and seven sixteenths (1-7/16) inch.
Side Roof Rail Weatherstrip
p/n: 20-2225-65
Seal, top iron to door glass. One (1) inch wide by thirty (30) inch length.
Fuel Neck Grommet
p/n: 20-2177-39
Grommet, fuel filler neck. Fully molded rubber with small retaining lip. Three and five eighths inch (3-5/8") outside diameter by two and nine sixteenths inch (2-9/16") inside hole diameter.
Upper Engine Mount
p/n: 20-1538-11
This Front or Rear Upper Engine Mount reproduction is designed from the original part for superior fitment and durability. This mount fits between the engine and chassis to support the engine and reduce harmonic vibrations.
Cowl Firewall Grommet
p/n: 20-1560-20
This Cowl Firewall Grommet fits into the upper section of the firewall for the main wiring harness. Also used to run the dash wires on the firewall and through the firewall.
Door Handle Gasket
p/n: 40-0133-70
Pad, door handle escutcheon. Two and three fourths (2-3/4) inch by one and one fourth (1-1/4) inch.Width: 2.75 inches. Height: 1.25 inches.
Wiring Harness Loom Grommet
p/n: 60-0255-14
This Grommet is designed from the original part for superior fitment. The grommet ideally works for the headlight or taillight wiring loom through body sheet metal. Four (4) to six (6) grommets per vehicle.
Body Mounting Pad
p/n: 40-0229-48
Pad, body mounting, upper. Fully molded rubber. One and three fourths inch (1-3/4") outside diameter by one half inch (1/2") inside hole diameter by one fourth inch (1/4") height.
Door Bumper
p/n: 40-0010-70
Pad, door jamb, fully detailed. One and one eighth (1-1/8) inch long, one and one fourth (1-1/4) inch wide.Length: 1.125 inches. Width: 1.25 inches.