Door Weatherstrips - Lower
p/n: 60-0078-73
This Lower Door Weatherstrip pair is designed from the original parts for superior fitment and seal. Heavy type with original ribbing and retainer lip.
Threaded Ends Insulator for Propeller Shaft and Exhaust Muffler
p/n: 70-0631-27
A steel core, double end threaded quality rubber Insulator that functions as an exhaust system muffler pipe bracket insulator. Also functions as a propeller shaft bearing to frame crossmember insulator.
Power brake carpet grommet
p/n: 70-3147-24
Grommet, carpet. Floor front carpet grommet use for power brake hole.
Windshield Division Bar Gasket
p/n: 70-0098-52
This Windshield Division Bar Gasket is designed from the original part for superior fitment and seal. Part combines inner and outer gasket in one piece as original. For seventeen (17") inch to (20") inch lengths.
Brake Pedal Pad - Dyna-Flow Transmission
p/n: 50-0285-22
This reproduction Pedal Pad slips over the full perimeter of the brake pedal for a precise, factory fit. For models with Dyna-Flow and standard brakes.
Steering Column Seal
p/n: 60-0518-36
Seal, steering column and shift column toe pan. Five eighths (5/8) inch thick sponge rubber.Width: 4.875 inches. Height: .625 inches.
Fender Welting
p/n: 20-1591-44
This black Fender Welting is designed from the original part for superior fitment and seal. This welting material fits between the fenders and the vehicle body. Eight (8) foot length.
Brake and Clutch Pedal Pad
p/n: 40-0287-22
Pads, brake and clutch pedal. Length: 3.625 inches. Width: 2.0 inches.
Brake and Clutch Pedal Pads
p/n: 70-3003-22
This reproduction Clutch and Brake Pedal Pad pair slips over the full perimeter of the brake pedal for a precise, factory fit. A square style direct fit reproduction to replace worn original pedal pads. Manufactured in black rubber.
Window Locking Strip - Black
p/n: 70-2195-52
This extruded Locking Strip is used to retain windshield gaskets in pickups and vans. Designed from the original part for superior fitment, finish and function. Available in 16ft lengths.
Side Window Vertical Leading Edge
p/n: 20-3126-80
Side window vertical leading edge weatherstrip. Cut to length. NOT cloth covered. This part attaches to the vertical edge of the rear side windows when the rear side windows are fully raised. Designed from the original part for superior fitment and seal.
Lock Pillar Water Deflector
p/n: 70-3635-62
Door panel water deflector, at lock. Fully molded for both left and right hand sides.
Brake and Clutch Pedal Pads
p/n: 60-0300-22
Pad, brake and clutch pedal.Length: 3.0 inches. Width: 2.5625 inches.
Rear Leaf Spring Insulator
p/n: 70-0980-32
This Rear Leaf Spring Insulator is an exact replacement for the upper and lower spring pad. Two and one half (2-1/2) inches wide, with cloth reinforcement. Four (4) used per car.
Metal Sleeved Grommet
p/n: 70-0203-41
Flanged rubber grommet with metal sleeve bushing. Used as part of the accelerator relay lever. Also used from 1959-61 on all Cadillac models as a bushing for the windshield wiper relay lever adaptor.
Body Mounting Pad
p/n: 27-0092-48
Insulator, body mounting pad. Metal core & locating collar covered with rubber.
Body Mount Isolator Pad
p/n: 70-0929-48
Body Mount Isolator Pad - Rubber with metal core and locating collar as original part. Part dimensions = Two and three sixteenths inch (2 3/16") square by one inch (1") overall height with thirteen sixteenths inch (13/16") inside bolt diameter. Does not include any fastener hardware.
Trunk Bumper
p/n: 70-0296-87
T-nut, trunk bumper in gutter at sides, brass core tapped 10-32 thread. Two (2) required per car. For models having partial weatherstrip in gutter of body.
Firewall Grommet
p/n: 70-2067-20
This Firewall Grommet is used to run the main wiring harness through the firewall. Designed from the original part for superior fit and seal.
Lower Rear Engine Mount
p/n: 20-0584-11
This Lower Rear Engine Mount is designed from original part for correct fitment and function. Made of a quality dense rubber for durability and proper engine vibration isolation. Two (2) required per truck.
Hood Bumper Set
p/n: 33-0680-42
This eight (8) piece Hood Bumper set is designed from the original parts for superior fitment and function.
1-7/16" Firewall Grommet
p/n: 60-0276-45
This Firewall Grommet is used to run the throttle rod and tube, oil pressure gauge pipe, heat indicator tube, and choke rod through the firewall.
Body Mounting Pad
p/n: 70-1429-48
Pad, body mounting. Fully molded rubber with metal core and rubber locating collar. Also used for radiator cradle to frame. Eight (8) to ten (10) required per car. Two and one fourth inch (2 1/4") outside diameter by one and one sixteenth inch (1 1/16") l
Body Mounting Pad
p/n: 50-0477-48
Pad, body mounting. Fully molded rubber with metal core & locating collar.
Vent Window Division Bar Weatherstrip
p/n: 70-1432-56
This Front Vent Window Division Bar Weatherstrip is designed from the original part for superior fitment and seal. A single 32" inch (approximate) length of original cross-section extruded rubber.
Starter Pedal Button Cover
p/n: 60-0166-21
This Starter Button Pedal Cover is designed from the original part for an authentic fit, finish, and appearance. Rubber slip over type for old metal. Two (2") inch outside diameter.
Firewall Grommet
p/n: 70-2066-24
This Firewall Grommet is used to run the emergency brake cable through the firewall. Designed from the original part for superior fit and seal.
Battery Hole Cover Seal
p/n: 20-0555-21
This Battery Hole Cover Seal is designed from the original part for superior fitment and seal. This part seals the battery hole cover to the vehicle floor.
Brake Master Cylinder Push Rod Boot
p/n: 60-0180-24
This Brake Master Cylinder Push Rod Boot is made from high-quality Nitrile rubber for a precise, factory like fit for your classic vehicle. Manufactured to OEM specifications to install for an authentic fit and finish.
Stabilizer Bar End Link Set
p/n: 60-0221-33
Twenty-two (22) piece Stabilizer Bar End Link set for both sides of one (1) vehicle, fits front or rear bar. Order two (2) sets for vehicles with front and rear stabilizer bars. Hex head bolt 3/8"-16 NF x 6-15/16" long. Comes with metal sleeve, metal cup washers and rubber grommets.
Rear Bumper End Fillers
p/n: 70-3774-30
This two (2) piece Rear Bumper End Filler pair is designed from the original part for a superior fitment level. These die cut masticated rubber pieces fit to the left and right bumper ends between the rear bumper and the vehicle body.
Hydraulic Pump Mounting Cushion
p/n: 70-0852-67
This Hydraulic Pump Mounting Cushion is designed from the original part for superior fitment and function. Used on models with hydraulic window lifts or a hydraulic convertible top. Two (2) to three (3) required per car.
Quarter Window Vertical Leading Edge
p/n: 70-0141-58
This quarter to side window Vertical Leading Edge Weatherstrip pair is designed from the original part for superior fitment and seal. Slides into metal retaining channel attached to rear side window and seals between the front door window and the rear quarter window.
Battery Clamp Cover
p/n: 70-0095-21
This Battery Clamp Cover helps to protect the nearby metal and finish. Fully molded from high-quality EPDM rubber to ensure durability. Good copy from an original part.