Gravel Shield
p/n: 30-0007-44
Gravel deflector, underside of running board at rear. Length: 7.125 inches.
Gravel Shield Bumper
p/n: 33-0286-30
Bumper, rear gravel shield, anti-rattle. Five (5) or more used per car. Fully molded rubber. Replaces factory #1320392.
Handbrake Seal
p/n: 60-0396-24
Seal, handbrake at floorboard. Rubber sponge, one (1) required per vehicle.Length: 4.50 inches. Width: 2.0 inches. Height: 1.25 inches.
Headlight Bucket To Fender Gasket
p/n: 20-1542-14
This Headlight Bucket To Fender Gasket is designed from the original part for superior fitment and seal. These gasket fits the headlight bucket and front fender.
Headlight Door To Lens Ring Seals
p/n: 70-0389-14
This Headlight Door To Lens Ring seal pair is designed from the original part for superior fitment and function. The part works to seal between the headlight door housing and the headlight retaining ring. The part is a single lip type seal for sealed beam headlights.
Headlight Door To Lens Weatherstrips
p/n: 70-0493-14
This Headlight Door To Lens Weatherstrip pair is the double lip type for sealed beam headlights. The pair is molded without wire. Designed from the original part to fit correctly.
Headlight Mounting Pad
p/n: 30-0354-14
Gasket, headlight front assembly to fender. Between headlight bucket and the fender receiver hole. One (1) pair per car, sold only in pairs.
Headlight Mounting Pad
p/n: 50-0462-14
Headlight housing to fender gasket. Steel rule die-cut replacement for #1320452.
Headlight Mounting Pad
p/n: 30-0142-14
Gaskets, headlight body mounting to fender. Cut to exact size as original.
Headlight Mounting Pad
p/n: 70-0201-14
This Headlight Mounting Pad is designed from the original part for superior fitment and seal. This pad acts as the headlight adjusting collar. Sold as a pair.
Headlight to fender gasket
p/n: 20-2295-14
Gasket, headlight bucket to fender. Cork. Two (2) required per vehicle.
Heel plate
p/n: 70-3608-88
Heel plate to protect driver's side floor carpet. Identical to original. Only for models with carpet.
Hinge seal
p/n: 70-0481-73
Filler, front door hinge pillar at dash, right and left. With metal core. Located at top front of front door, under door flange.
Hood and Trunk Bumper Cap for Adjustment Screw
p/n: 70-0294-42
This Hood and Trunk Bumper Cap is designed from the original part for superior fitment, finish and function. Cap type for front hood or rear trunk lid adjustment screw.
Hood bumper
p/n: 50-0326-42
Bumper, hood side pilot. Four (4) piece set required per car. Steel washer vulcanized inside rubber.
Hood Bumper
p/n: 70-0409-42
Bumpers, hood top panel at cowl. One half (1/2) inch by one half (1/2) inch by three and one fourth (3-1/4) inch. Held in place by screws. Two (2) to four (4) per car as required.
Hood Bumper
p/n: 50-0325-42
Bumper, hood front. Slides over metal bracket.1941 model requires two (2) per car. 1942 model requires two to four (2-4) per car.Length: 1.0 inches.
Hood Bumper Set
p/n: 20-0358-42
This fourteen (14) piece Hood Bumper set is designed from the original parts for superior fitment and function.
Hood Bumper Set
p/n: 20-1588-42
This twelve (12) piece Hood Bumper set is designed from the original parts for superior fitment and function.
Hood Corner Pad
p/n: 40-0127-42
Pads, hood corners, brass core. Approximately 80 degree angle. Integral tabs for installing.Length: 1.50 inches.
Hood Corner Pad
p/n: 60-0118-42
Pad. hood corner, steel core as original, front and rear.Length: 1.5 inches.
Hood rest pad
p/n: 70-0139-42
Pad, hood rest (hood bumper). In years 1941-47 purchase six (6) per car. In year 1948-1949 purchase two (2) per car.
Hood Support Rod Top Cap
p/n: 40-0346-42
Pad, hood rest rod. For five sixteenths (5/16) inch diameter hood support rod. Also see our #40-0103-42.Length: 1.0 inches.
Hood to Cowl Weatherstrip
p/n: 27-0027-42
This Hood to Cowl Weatherstrip is a self-retaining set that consists of two (2) halves.
Hood to Cowl Weatherstrip
p/n: 60-0056-42
This Hood to Cowl Weatherstrip is extruded from a high quality dense rubber for a durable and proper seal. This seal mounts at the rear of the engine bay to seal between the hood and vehicle body cowl.
Hood to Cowl Weatherstrip
p/n: 70-1206-42
Weatherstrip, hood to cowl. To facilitate manufacturing, some may be made in two sections.
Hood to Cowl Weatherstrip
p/n: 30-0049-42
Scuff pad, hood to cowl. Superior duplication of part with better rubber than original.Length: 8.25 inches.
Hood To Cowl Weatherstrip
p/n: 70-1207-42
This Hood To Cowl Weatherstrip has self-retaining stems as original. Made in two pieces to facilitate manufacturing. May need modification by customer to interlock the halves (38" long) into appearing as one continuous strip.
Hood to Cowl Weatherstrip
p/n: 50-0142-43
This Hood to Cowl Weatherstrip pair is designed from the original part for superior fitment and seal. An exact reproduction of the original profile. This left and right seal pair mounts at the rear of the engine bay to seal between the hood and the vehicle body cowl.
Hood to Cowl Weatherstrip
p/n: 60-0138-42
This Hood To Cowl Weatherstrip pair installs at the rear of the engine bay to seal between the hood and vehicle body cowl. Sold as a pair for left and right side.
Hood to Cowl Weatherstrip
p/n: 70-1208-42
Weatherstrip, hood to cowl. To facilitate manufacturing, some may be made in two sections.
Horn button contact cushion
p/n: 50-0409-21
Separator, horn contact. For standard or non-flexible wheel.
Horn Button Contact Set
p/n: 60-0492-21
This is a three (3) piece Horn Button Contact set which is designed from the original part for superior fitment and function. Renews the operation of the steering wheel horn blowing ring.
License Light Mounting Pad
p/n: 70-1222-17
Pad set, license light mount and lens gasket.Length: 12.625 inches.
License Light Mounting Pad
p/n: 70-1223-17
Pad set, license light mount and lens gasket.Length: 12.625 inches.