Hood to Cowl Weatherstrip
p/n: 60-0056-42
This Hood to Cowl Weatherstrip is extruded from a high quality dense rubber for a durable and proper seal. This seal mounts at the rear of the engine bay to seal between the hood and vehicle body cowl.
Front Fender to Apron Seal
p/n: 20-2504-45
This Front Fender to Apron Seal installs on the fender to inner apron. Excellent for when assembling front sheet metal. Sold as a fifteen (15) foot roll.
Rigid Run Channels
p/n: 70-0516-58
This Rigid Run Channel pair is zinc plated steel with black cloth inside lining to provide a smooth sliding surface for glass movement. Also works to protect the glass. Fastens in place by small screws or rivets on top and bottom.
Convertible Top Rest Bump Stop Block
p/n: 70-0397-67
This Convertible Top Rest Bump Stop Block pair is designed from the original part for an authentic fit, finish, and appearance. Attaches to the folding pillar arm of the convertible top assembly. This rubber only bumper block glues to the original metal core.
Front Bow Weatherstrip
p/n: 12-0016-64
Weatherstrip, windshield top to front bow, original type sponge rubber. Four (4) foot strip.
Fabric Hood Lacing
p/n: 20-0354-42
This Fabric Hood Lacing installs where the hood rests on the cowl panel. Original woven style lacing complete with installation tacks. Sold as a forty-nine (49) inch strip.
Taillight Mounting Pads
p/n: 20-2407-15
This Taillight Mounting Pad pair is designed from the original part for superior fitment and sealing. These reproduction gaskets fit between taillight frame housing and the body.
Fuel Tank Filler Neck Grommet
p/n: 20-0345-39
This Fuel Tank Filler Neck Grommet is designed from the original part for superior fitment and seal. This grommet fits around the vehicles fuel filler neck between the filler neck and vehicle body.
Cowl Vent Gasket
p/n: 60-0124-54
Gasket, cowl vent. Original labyrinth style, not sponge.Length: 16.5 inches. Width: 4.0 inches.
Gearshift Floorplate
p/n: 20-0464-88
Seals, transmission cover to floor. Cork and rubber. Three (3) piece set.
Brake and Clutch Shank Seal
p/n: 40-0175-24
Seal, brake and clutch pedal shank to floorboard. One and one half (1-1/2) inch by two and one eighth (2-1/8) inch by three fourths (3/4) inch thick.
Sash Channel Weatherstrip
p/n: 60-0690-58
Weatherstrip, sash channel. Correct extrusion. Two (2) strips cut twenty five and one half (25-1/2) inches long.
Vent Window Division Post Weatherstrips
p/n: 20-0470-56
This Vent Window Division Post Weatherstrip is fully molded in high quality rubber and with a metal core. This part fits opposite the glass run channel and seals the vent window when the vent is closed. Part installs using the included rivets.
Parking light gasket
p/n: 70-2651-16
Gaskets, front parking light. Lamp base. For lens gasket see our #70-2652-16. This style used on Series 75 models only with small parking lamp.
Side Window Sash Channel
p/n: 70-0641-58
This Side Window Sash Channel is the u-shaped steel channel only, no filler. Sold in 4 foot strip, usually sufficient for two (2) windows.
Brake and clutch shank seal
p/n: 70-0465-23
Grommets, brake and clutch pedal shank below floorboard.
Tail light lens gasket
p/n: 70-3721-15
Gasket, taillight lens, two (2) piece set. Circular gasket stretches over oval shaped lens. Replaces factory #410622.
License Lens Gasket
p/n: 70-2276-16
Gasket, license light lens. Fully molded with proper details.Length: 3.0 inches. Width: 1.6875 inches.
Rear Bumper Gravel Shield
p/n: 60-0173-30
This Rear Bumper Gravel Shield, also known as a rear bumper face bar-to-body seal, is made of high quality dense rubber. Fully molded rubber with all original features.
Vent Window Division Bar Weatherstrip
p/n: 20-2535-56
This Front Vent Window Division Post Seal pair is designed from the original part for superior fitment and seal. This part fits opposite the glass run channel and seals the vent window when the vent is closed.
Vent Window Division Bar Weatherstrip
p/n: 20-2536-56
This Front Vent Window Division Bar Weatherstrip pair is designed from the original part for superior fitment and seal. Parts are fully molded with a metal core and attached with rivets on the backside.
Horn button contact cushion
p/n: 50-0409-21
Separator, horn contact. For standard or non-flexible wheel.
Headlight Mounting Pad
p/n: 70-0201-14
This Headlight Mounting Pad is designed from the original part for superior fitment and seal. This pad acts as the headlight adjusting collar. Sold as a pair.
Fuel Tank Filler Neck Grommet - Panel Truck
p/n: 20-0486-39
This Fuel Tank Filler Neck Grommet is designed from the original part for superior fitment and seal. This grommet fits around the vehicles fuel filler neck at the vehicle body panel.
License Light Mounting Pad
p/n: 40-0391-85
Pad, trunk handle and license light housing.Length: 5.875 inches.
Flexible Run Channel - 5ft
p/n: 70-1107-57
Cloth covered mohair-lined type. For sides and top of side windows. Available in 5ft lengths.
Door Bumper
p/n: 34-0469-71
Bumpers, front door, upper. Approximately five eighths (5/8) inch square, three eighths (3/8) inch inside diameter. Steel core, retained by screw.
Trunk Weatherstrip
p/n: 20-2618-84
This Trunk Weatherstrip is designed from the original part for superior fitment and seal. The seal mounts around the full perimeter of the trunk lid.
Front Stabilizer Bushing
p/n: 60-0088-34
This Front Stabilizer Bushing pair is fully molded from EPDM dense rubber to ensure durability. Used to connect the stabilizer bar to the vehicle frame. Two (2) required per car.
Hydraulic Pump Grommet
p/n: 70-0640-21
Grommet, two (2) hole, for hydraulic pump through sheet metal.Length: 1.9375 inches. Width: 1.125 inches.
Decklid Lock / Handle Mount Gasket
p/n: 30-0126-87
This Decklid Lock / Handle Mount Gasket is designed from the original part for superior fitment, finish and function. Length: 4 inches.
Headlight Mounting Pad
p/n: 30-0142-14
Gaskets, headlight body mounting to fender. Cut to exact size as original.
Fender Welting with 3/16 Bead - 25ft
p/n: 70-1099-44
A superior quality Fender Welting material constructed of reinforced black vinyl over a vinyl core. Typically used for attaching two (2) fenders to body. Sold in a 25 foot roll.
Windshield Gasket
p/n: 70-2457-50
This windshield gasket is designed from the original part for superior fitment and seal. The seal mounts around the full perimeter of the front glass and has vulcanized, or bonded, ends which means no cutting or splicing is required for installation.
Trunk Compartment Door Handle Pad
p/n: 20-2630-86
This Trunk Compartment Door Handle Pad is designed from the original part for superior fitment, appearance and function. This unique mounting pad fits between the door handle and the trunk luggage compartment door.
Suspension Bumper - Front Lower Control Arm
p/n: 50-0092-32
This Suspension Bumper is designed from the original part for superior fitment and function. Bumper mounts to the front suspension lower control arm. Two (2) per car required.
Cab To Frame Body Mounting Pad Set
p/n: 20-0459-48
This twenty-two (22) piece Cab To Frame Body Mounting Pad set is designed from the original parts for superior fitment and function. Contains all the necessary rubber pads, bushings, blocks and washers.
Fender Skirt Edge Weatherstrip
p/n: 60-0109-45
This Fender Skirt Edge Weatherstrip pair is designed from the original part for superior fitment, finish, and seal. This weatherstrips fits between the rear wheel fender skirt and the rear fender quarter panel.
Window Felt Beltline Weatherstrips - 3ft Pair
p/n: 30-0244-57
This side window Window Felt Beltline Weatherstrip pair can be used as inner and/or outer. The weatherstrip is flexible, pile lined, rubber covered, with black bead. Available in 3ft pairs.
Chrome Fender Welting - 25ft
p/n: 70-1101-44
Welting, fender, bright chrome vinyl, three sixteenths (3/16) inch bead, one and one half (1-1/2) inch width. Superior quality. Twenty five (25) foot roll. Typically used to attach two (2) fenders to body. For fifty (50) foot roll see our #70-1102-44.