Clutch and Brake Pedal Pads - BLACK
p/n: 25-0024-22
This reproduction Clutch and Brake Pedal Pad pair slips over the full perimeter of the brake pedal for a precise, factory fit. A reproduction with authentic type ribbing, to replace worn original pedal pads. Manufactured in Black rubber.
Brake Master Cylinder Filler Access Hole Cover
p/n: 60-0016-24
This Master Cylinder Access Hole Cover is designed from the original part for superior fitment and seal. Secures the Brake Master Cylinder Filler and Inspection Access Hole in the vehicle.
1935-1974 Cadillac Factory Parts Manual, CD
p/n: 07-1346-07
This GM Licensed Detroit Iron CD provides the most comprehensive set of digital Cadillac Factory parts manuals. The factory manuals on this CD were professionally scanned from the original service and parts manuals.
Hood Corner Pad
p/n: 27-0031-42
Pads, hood front corners, right and left. Metal core as original with integral mounting tabs for hole in hood corner.Width: 1.875 inches. Height: .
Door - Gravel Shield - Running Board Weatherstrip
p/n: 60-0054-73
This Door - Gravel Shield - Running Board Weatherstrip is a anti-squeak bulb type extrusion with fitment for General Motors vehicles. A twelve (12) foot strip made of high-quality EPDM dense rubber and designed from original parts for superior fitment, finish and function.
Flexible Run Channel - 60 Inch
p/n: 20-1619-58
Channel, side window glass, vertical run. Flexible, felt lined, rubber covered channel. Available 60" lengths.
Brown Gearshift Boot
p/n: 40-0111-89
Boot, base of gearshift lever. Brown rubber. For black see our #40-0111-88. Made separately to fit most of our gearshift floorplates. Copied from original.
Flexible Run Channel
p/n: 20-1146-58
This Flexible Run Channel helps to eliminate window rattle, provides a smooth sliding surface for glass movement, and works to protect the glass. Stainless steel beaded. Available in sixty (60) inch strips.
Fuel Neck Grommet
p/n: 30-0241-41
Grommet, gas tank inlet to wheel housing. Also used as grommet, gas tank inlet tube to wheel compartment bottom.
Transmission Mounting Pad
p/n: 11-0025-25
Mount, transmission. Original pattern, superior workmanship.
Fuel Neck Grommet
p/n: 40-0272-39
Grommet, fuel filler neck. Oblong shape, fully molded rubber. Four and one fourth inch (4-1/4") outside width by five and five eighths inch (5-5/8") outside length by seven eighths (7/8") height.
Hood Corner Pads
p/n: 40-0187-42
This Hood Corner Pad pair is an exact copy of the original. This pad fits between the engine hood and the body to isolate noise and vibration.
Rear Axle Bumpers
p/n: 20-0342-32
This Rear Axle Bumper pair is designed from the original part for superior fitment and function. Bumper is manufactured with top quality materials for good durability.
Hood Bumper Set
p/n: 20-0356-42
This comprehensive Hood Bumper set is designed from the original part for superior fitment and function. The sixteen (16) piece set includes four (4) grille area bumpers and four (4) cowl bumpers with eight (8) rivets.
Taillight Mounting Pad
p/n: 50-0078-15
Taillight mounting pad. Excellent copy with proper lip at edge. Replaces #1273863. Customer must cut holes for wires, bulb, screws etc as required.
Fuel Neck Grommet
p/n: 70-0404-39
Grommet, fuel filler neck. Fully molded rubber. Flat bottom has slight ridge (seam) along edge. Four and three eighths inch (4-3/8") outside diameter by two and three sixteenths inch (2-3/16") inside hole diameter by five eighths inch (5/8") height.
Radiator Mounting Pad
p/n: 30-0208-31
Pad, radiator lower splasher to grille. Fastens into place with rivets. One four (4) piece set required per car.Length: .875 inches. Width: .875 inches.
Accelerator Pedal Pad
p/n: 40-0113-40
Pad, accelerator pedal. Black rubber. Slipover type. Exact pattern, perfect copy in all details.
Front Bumper Arm Grommets
p/n: 20-2004-28
This Front Bumper Arm Grommet pair is designed from the original part for an authentic fit, finish, and appearance.
Gearshift Boot - Black
p/n: 20-0334-26
This reproduction Black Gearshift Boot is designed from the original part for an authentic fit, finish, and appearance.
Brake Cable Anti-Rub Cover
p/n: 60-0443-24
Sleeve, rear brake cable anti-rub. Six (6) piece set. One half (1/2) inch inside diameter, seven eighth (7/8) inch outside diameter.
Brake Cable Boot
p/n: 60-0156-24
Boot, front brake cable end at brake backing plate. Two and seven eighths (2-7/8) inches long.Length: 2.875 inches.
Fuel Neck Grommet
p/n: 70-0050-39
Grommet, fuel filler neck. Fully duplicates original with large retaining flange. Flexible, molded rubber. Four and one eighth inch (4-1/8") outside diameter by two and three sixteenth inch (2-3/16") inside hole diameter.
Rigid Run Channels
p/n: 70-0347-58
This Rigid Run Channel pair is stainless beaded and mohair-lined to help eliminate window rattles and provide a smooth sliding surface for glass movement. Also works to protect the glass.
2-3/8" Firewall Grommet
p/n: 30-0056-21
This Firewall Grommet is made to run the ignition cable and thermometer tube through the firewall. Designed from the original part for superior fit and seal.
Firewall Pass Through Grommet
p/n: 40-0522-21
This Firewall Pass Through Grommet is the rectangular large type. Designed from the original part for superior fit and seal.
Coil wire sleeve
p/n: 70-0109-21
Sleeve, coil wire to distributor. Fluted to match upper water hoses rubber only. V-12 & V-16 with coils mounted in radiator, V-8 with coils mounted horizontally on brace rods.
Cowl Vent Gasket
p/n: 30-0179-54
Gasket, cowl vent, original labyrinth type, not sponge.Length: 14.75 inches. Width: 5.50 inches.
Engine Mount
p/n: 30-0292-11
This Engine Mount pair is used as the engine crank case link ball insulator. Correctly designed with careful attention to detail as original. Sold only in pairs.
Side Mount Grommet
p/n: 30-0100-37
Grommets, spare wheel sidemount brace, lower.Length: 2.625 inches. Width: 2.50 inches.
Flexible Run Channel - 6 Ft.
p/n: 70-1108-57
Channel, flexible window run, un-beaded. Cloth covered mohair-lined type. Available in 6ft lengths.
Cowl Vent Gasket
p/n: 14-0037-54
Gasket stock, cowl vent, high grade sponge of proper cross-section, (not molded into ring), approximately forty eight (48) inch strip per car.
Cowl Vent Gasket
p/n: 20-2049-54
This Cowl Vent Gasket is designed from the original part for superior fitment and seal. This gasket works to seal the cowl vent when closed into the cowl body. Made from top quality rubber to ensure durability and proper seal.
Fuel Neck Grommet
p/n: 10-0120-41
Grommet, fuel filler neck. Fully molded rubber. Three and five eighths inch (3-5/8") outside diameter by two and five eighths inch (2-5/8") inside diameter by thirteen sixteenths inch (13/16") height.
Headlight Mounting Pad
p/n: 60-0211-14
Mounting pad, headlight bracket to fender.Length: 4.8125 inches.
Hood to Cowl Fabric Lacing
p/n: 20-2022-43
This Hood To Cowl Fabric Lacing is designed from the original part for superior fitment and seal. This lacing attaches to the cowl at the rear of the engine bay to fit between the hood and cowl with hood closure.
Rumble Seat Step Pad
p/n: 60-0126-45
Pad, rumble seat step, on rear bumper bracket or fender. Rubber cover only, full slip-over type with bowtie emblem.
Rumble Seat Step Pad
p/n: 27-0005-44
Pad, rear bumper step, rubber only. Fits old metal core.Height: .8125 inches.
Beltline Weatherstrips
p/n: 40-0539-57
This Beltline Weatherstrip pair installs on the left and right doors to wipe the inside and outside of the windows when the glass is lowered. Flexible, pile lined, rubber covered, with a black bead. Available in 3ft pair.
Flexible Run Channel
p/n: 70-1239-58
This Flexible Run Channel provides a smooth sliding surface while helping to eliminate rattle and protect the glass. The run channel has the stainless beaded edge and is cloth covered and mohair lined with the flexible metal channel.
Fuel Neck Grommet
p/n: 40-0139-39
Grommet, fuel filler neck. Fully molded rubber, slightly angled. Four and one half inch (4-1/2") outside width by four and five eighths inch (4-5/8") outside length by two and one fourth inch (2-1/4") inside hole diameter.
Side Mount Clamp Cushion
p/n: 40-0138-37
Cushion, sidemount clamp. Two and one eighth (2-1/8) inch by four and five eighths (4-5/8) inch.Length: 4.625 inches. Width: 2.125 inches.
Windshield mounting pad
p/n: 60-0362-52
Pad, windshield side arm-to-cowl, right and left. Replaces #370356.
Engine Mount Pad
p/n: 11-0026-11
This Engine Mount Pad is designed to original pattern with superior workmanship. Made from high-quality EPDM rubber for a precise, factory like fit. Two (2) required per car.
Door Bottom weatherstrip
p/n: 70-3140-73
Seal, lower door. Mounts to door scuff plates. Enough for 4 doors.
Vent division bar weatherstrip
p/n: 30-0461-56
Front vent window division post seal. Fully molded with metal core and attaching tabs.
Headlight Mounting Pad
p/n: 60-0178-14
Pads, headlight bracket mounting. Two (2) inch by three and five eighths (3-5/8) inch overall.Length: 3.625 inches. Width: 2.0 inches.
Cowl Vent Weatherstrip
p/n: 70-0224-54
Weatherstrip, cowl vent. Original solid rubber configuration, not a sponge substitute. A top quality part for your classic vehicle restoration.
Gearshift Boot
p/n: 40-0111-88
Boot, base of gearshift lever. Black rubber. For brown see our #40-0111-89. Made separately to fit most of our gearshift floorplates. Copied from original.
Rumble Seat Step Mounting Pad
p/n: 30-0271-44
Gasket, rumble seat step center. Length: 5.875 inches.
Starter pedal pad
p/n: 40-0200-21
Pad, starter pedal. Excellent quality with detail and workmanship as found in original.
Swing-Out Windshield Weatherstrip
p/n: 20-3174-50
This Swing-Out Windshield Weatherstrip is designed from the original part. The weatherstrip mounts into the metal channel attached to the glass and creates a seal when the glass is pressed against the body of the vehicle.
Taillight Mounting Pad
p/n: 40-0198-15
Pad, taillight mounting. Plain type, no bead. Length: 6.0625 inches. Width: 2.375 inches.
Vent Division Bar Weatherstrip
p/n: 60-0509-56
This Vent Division Bar Weatherstrip is fully molded with metal core and attaching tabs. Sold as a pair for the drivers (LH) and passenger (RH) doors.
Vent Division Bar Weatherstrip
p/n: 50-0407-76
This Vent Division Bar Weatherstrip is fully molded with metal core and attaching tabs.
Window Felt Beltline Weatherstrips
p/n: 70-0555-58
These Window Felt Beltline Weatherstrips are sold as a three (3) foot pair. The beltline is used for side windows inner and/or outer, front and/or rear doors. Available in a 3ft pair.
Brake Cable Boot
p/n: 60-0155-24
Boot, rear, brake cable end at brake backing plate. Three and one half (3-1/2) inches long.Length: 3.50 inches.
Headlight Mounting Pad
p/n: 50-0218-14
Headlight bracket-to-fender mounting pads. Replaces #1283932-3, right and left.
Running Board or Inner Fender Splash Filler
p/n: 60-0288-45
This eight (8) foot Splash Filler strip is used for the running board apron to body or fender splash panels anti-rattle filler. This filler strip is top-quality EPDM sponge rubber to accept rivets or retaining screws.
Fuel Neck Grommet
p/n: 60-0543-41
Seal, gas tank filler tube through floor pan, to inside of body. Made of soft flexible durometer rubber. Four and seven sixteenths inch (4-7/16") outside width by five and five eights inch (5-5/8") outside length.
Brown Gearshift Boot
p/n: 50-0035-89
Boot, gearshift. Brown rubber. For black see our #50-0035-24.Color:brown Width: 2.8125 inches.
Brake and Clutch Shank Seal
p/n: 30-0143-24
Boot, brake and clutch pedal shank at toe board.Length: 2.9375 inches.
Rear spring bushing
p/n: 60-0311-35
Bushing, rear spring front eye, inlox cartridge type as original.
Clutch and Brake Pedal Pads - Brown
p/n: 50-0054-89
This reproduction Clutch and Brake Pedal Pad pair slips over the full perimeter of the pedal for a precise, factory fit. A perfect reproduction to replace worn original pedal pads. Manufactured in quality brown rubber.
Flexible Run Channel
p/n: 70-1238-58
Cloth covered, mohair lined flexible metal channel for sides and top of door windows.
Accelerator Pedal Pad
p/n: 60-0097-40
Pad, accelerator pedal. Slip-over type for original core. Length: 9.125 inches.