Front Door Vent Window Weatherstrips
p/n: 17-0015-55
These front door vent window seals are designed from the original parts for superior fitment and seal. The pieces are molded as left and right and are one piece with the division post seal.
Front Door Vent Window Weatherstrips
p/n: 38-0022-55
These Front Door Vent Window Weatherstrips are the main seals needed to replace the rubber on your vent windows. They are designed and molded from original parts for superior fitment and seal.
Front Engine Mounting Pad
p/n: 50-0229-11
This Engine Mount Pad is designed to original specifications with superior workmanship. Made of a high-quality EPDM dense rubber for durability and authentic fit.
Front Fender Seal
p/n: 30-0189-44
Liners, front fender to running board. Reversible right and left like original. Length: 15.0 inches.
Front Fender Seal
p/n: 30-0264-44
Liner, front fender to running board. Reversible right and left replacement. Length: 15.50 inches.
Front Hood Corner Pads
p/n: 14-0035-42
This Front Hood Corner Pad pair is an exact copy of the original. This pad fits between the engine hood and the body to isolate noise and vibration.
Front spring bumper
p/n: 30-0227-32
Bumper assembly, front spring rebound (upper arm). Steel core, with treaded stud just like original.
Front Spring Bumper
p/n: 70-0339-32
Bumper, front spring, upper arm on frame. Rubber with heavy steel core, including five sixteenths (5/16) inch stud.
Front Spring Bumper
p/n: 60-0021-35
Rebound bumper, front spring and rear spring for beam axle cars, steel ring reinforced as original.Height: 2.4375 inches.
Front spring bushing
p/n: 30-0393-32
Bushing assembly, front wheel support; upper and outer. Inlox type cartridge bushing assembly.
Front Suspension Bumper
p/n: 30-0228-32
Bumper assembly, front suspension inside coil spring, with five sixteenths (5/16) inch threaded studs as found originally.
Front suspension bushing
p/n: 30-0239-32
Bushings, front suspension torque arm. Necessary for proper front end geometry.
Front Suspension Rebound Pad
p/n: 50-0083-32
Rebound pad, front suspension, upper arm, on frame. Rubber body, steel core with five sixteenths (5/16) inch stud.
Fuel Filler Neck Grommet
p/n: 60-0022-41
This Fuel Filler Neck Grommet is fully molded rubber and slightly angled. Three and eleven sixteenths inch (3-11/16") outside diameter by two and three sixteenths inch (2-3/16") top hole diameter by two and five eighths inch (2-5/8") bottom hole diameter.
Fuel Neck Grommet
p/n: 30-0101-41
Grommet, fuel filler neck. For inside of body, on floor of wheel carrier.
Fuel Neck Grommet
p/n: 60-0181-41
Grommet, fuel filler neck. Fully molded rubber, slightly angled with retaining flange. Three and seven sixteenths inch (3-7/16") outside width by three and five eights inch (3-5/8") outside length.
Fuel Neck Grommet
p/n: 25-0015-39
Grommet, fuel filler neck. Oblong, fully molded rubber. Flat bottom has slight ridge (seam) along edge.
Fuel Neck Grommet
p/n: 60-0543-41
Seal, gas tank filler tube through floor pan, to inside of body. Made of soft flexible durometer rubber. Four and seven sixteenths inch (4-7/16") outside width by five and five eights inch (5-5/8") outside length.
Fuel Neck Grommet
p/n: 70-0050-39
Grommet, fuel filler neck. Fully duplicates original with large retaining flange. Flexible, molded rubber. Four and one eighth inch (4-1/8") outside diameter by two and three sixteenth inch (2-3/16") inside hole diameter.
Fuel Neck Grommet
p/n: 40-0272-39
Grommet, fuel filler neck. Oblong shape, fully molded rubber. Four and one fourth inch (4-1/4") outside width by five and five eighths inch (5-5/8") outside length by seven eighths (7/8") height.
Fuel Neck Grommet
p/n: 30-0241-41
Grommet, gas tank inlet to wheel housing. Also used as grommet, gas tank inlet tube to wheel compartment bottom.
Fuel Neck Grommet
p/n: 10-0120-41
Grommet, fuel filler neck. Fully molded rubber. Three and five eighths inch (3-5/8") outside diameter by two and five eighths inch (2-5/8") inside diameter by thirteen sixteenths inch (13/16") height.