Rumble Seat Lid Bumper Pad
p/n: 30-0275-44
Bumpers, rumble seat stop bracket. Self-retaining type as original.Length: 1.1875 inches. Width: .75 inches. Height: .375 inches.
Rumble Seat Lid Bumper Pad
p/n: 60-0191-87
Bumper pad, rumble seat lid, upper corners. Compare with our #70-0120-87.Width: 1.0 inches. Height: 1.125 inches.
Rumble Seat Lid Corner Pad
p/n: 70-0120-87
Pad, rumble seat lid corner, Compare with our #60-0191-87. Length: .75 inches.
Rumble Seat Step Mounting Pad
p/n: 30-0272-44
Gasket, rumble seat step. For left hand drive upper. Length: 5.0 inches.
Rumble Seat Step Mounting Pad
p/n: 70-0043-44
Pad, rumble seat step mounting for fender, double beaded edge per original. Width: 4.375 inches.
Rumble Seat Step Mounting Pad
p/n: 25-0019-44
Mounting pad for our #25-0018-44 fender step. Length: 7.375 inches.
Rumble Seat Step Mounting Pad
p/n: 30-0271-44
Gasket, rumble seat step center. Length: 5.875 inches.
Rumble Seat Step Mounting Pad
p/n: 30-0181-44
Pad, rumble seat step bracket to fender. Four and one fourth (4-1/4) inch long.Length: 4.375 inches.
Rumble Seat Step Pad
p/n: 27-0005-44
Pad, rear bumper step, rubber only. Fits old metal core.Height: .8125 inches.
Rumble Seat Step Pad
p/n: 40-0055-44
Pad, rumble seat step, with "DeSoto" logo, full slipover type to fit old carcass and outer trim ring. See also our #40-0353-44.Height: .50 inches.
Rumble Seat Step Pad
p/n: 60-0126-45
Pad, rumble seat step, on rear bumper bracket or fender. Rubber cover only, full slip-over type with bowtie emblem.
Rumble Seat Step Pad
p/n: 40-0412-44
Step pad, rumble seat upper, with "P" logo. Fully molded with core and mounting stud.Height: .625 inches.
Rumble Seat Step Pad
p/n: 25-0018-44
Step, rumble seat fender with molded-in studs. Length: 6.375 inches.
Rumble Seat Step Pad
p/n: 60-0501-45
Step pad, rumble seat, on rear fender, with bowtie emblem. Steel core with bolt.Width: 4.375 inches. Height: 5.25 inches.
Rumble Seat Step Pad
p/n: 40-0413-44
Step pad, rumbleseat, upper, with Chrysler medallion logo. Fully molded with core and mounting stud.Height: .625 inches.
Rumble Seat Weatherstrip
p/n: 25-0025-85
This Rumble Seat Weatherstrip set is designed from original parts for superior fitment and seal. The set contains the pieces for the lower edge and corners.
Run Channel Retaining Clip
p/n: 60-0374-58
This Run Channel Retaining Clip is designed from the original part for an authentic fit, finish and function. Clip fits at the end of door window run channel. Tempered spring steel.
Running Board Edge Seal
p/n: 30-0169-44
Liner, running board to body, (side apron to body seal). Set consists of two (2) pieces seven (7) foot long. One (1) inch width is after fold over.
Running Board Matting
p/n: 30-0214-49
Running board matting. Fully molded right and left hand. Top quality rubber, flawless detail. Includes rubber cross molding for in front of rear fender.
Running Board or Inner Fender Splash Filler
p/n: 60-0288-45
This eight (8) foot Splash Filler strip is used for the running board apron to body or fender splash panels anti-rattle filler. This filler strip is top-quality EPDM sponge rubber to accept rivets or retaining screws.
Shock Absorber Arm Bushing
p/n: 60-0106-32
This Shock Absorber Arm Bushing is designed from the original part for superior fitment and function. Manufactured to OEM original standards.
Shock Absorber Arm Bushing
p/n: 30-0192-32
Bushing, shock absorber arm. Restore proper shock action.Height: 1.375 inches.
Shock Absorber Bushing
p/n: 50-0087-33
Bushing, Delco type, shock absorber link. One and five sixteenths (1-5/16) inch outside diameter, seven sixteenths (7/16) inch inside diameter.
Shock Absorber Link Arm Bushing
p/n: 60-0216-33
This Shock Absorber Link Arm Bushing is designed from the original part for superior fitment, finish and function. This bushing is for double acting shock absorber arm links.
Shock and Stabilizer Grommet
p/n: 70-0274-33
This Shock and Stabilizer Grommet is fully molded using EPDM dense rubber. Designed from original with locating collar. Eight (8) required per car.
Shock and stabilizer seal
p/n: 70-1185-33
Seals, shock absorber and rear stabilizer link. Eight (8) piece set.
Shock and Stabilizer Seal
p/n: 70-1184-33
Seals, shock absorber and rear stabilizer link. Eight (8) piece set. Width: 1.1875 inches.
Shock and Sway Bar Grommet
p/n: 30-0193-33
Grommet, rear shock arm link (lower end), or rear sway bar link lower end. Shock arms used four (4) per car. If needed, sway bar used two (2) per car. Fully molded rubber.
Shock or Stabilizer Link Cross Pin Bushing
p/n: 50-0220-32
This Shock or Stabilizer Link Cross Pin Bushing is designed from the original part for superior fitment and function. A rubber bushing for shock absorber link cross pin or stabilizer cross link pin.
Side Mount Clamp Cushion
p/n: 40-0138-37
Cushion, sidemount clamp. Two and one eighth (2-1/8) inch by four and five eighths (4-5/8) inch.Length: 4.625 inches. Width: 2.125 inches.
Side Mount Grommet
p/n: 40-0140-37
Grommet, sidemount carrier brace to fender. One and five sixteenths (1-15/16) inch outside diameter by one half (1/2) inch inside diameter.
Side Mount Grommet
p/n: 30-0135-37
Grommets, sidemount carrier arm through fender. Reversible for right and left hand.Height: 4.0 inches.
Side Mount Grommet
p/n: 30-0100-37
Grommets, spare wheel sidemount brace, lower.Length: 2.625 inches. Width: 2.50 inches.
Side Mount Spare Grommet Set
p/n: 70-0180-37
This Side Mount Spare Grommet Set is made from top-quality EPDM rubber and designed from the original parts for durability and proper function. This set is for the rear spare wheel mount on cars without a luggage rack.
Side Mount Spare Wheel Grommet
p/n: 70-0099-37
Grommets, spare wheel sidemount arm.Width: 3.625 inches.
Side Mount Spare Wheel Grommet
p/n: 70-0341-37
Grommets, sidemount. These are the very large type, right and left. Used simultaneously with our #70-0388-37. Compare with your original. (See also our #70-0388-37).
Side Mount Spare Wheel Grommet
p/n: 70-0388-37
Grommets/seals, for sidemounted spares, cover hole in fender. Large, fully flanged for fender metal, compare to our #70-0341-37 and your original. Symmetrical, right and left. Approximately five and three fourths (5-3/4) inches by eight (8) inches outside
Side Mount Spare Wheel Grommet
p/n: 50-0082-37
Grommet set, side mounted spare wheel brace. Four (4) piece set with two (2) different sizes.
Side Mount Tire Cushion
p/n: 30-0410-37
Cushion, upper (thin) spare wheel in fender well. Two (2) per car.Length: 11.25 inches. Width: 3.0 inches.
Side Mount Tire Cushion
p/n: 30-0411-37
Cushion, lower (thick) spare wheel in fender well. Two (2) per car.Length: 11.0 inches. Width: 3.0 inches.
Side Roof Rail Weatherstrip
p/n: 40-0095-65
Weatherstrip, convertible top to side windows. Fifteen sixteenths (15/16) inch by five eighths (5/8) inch. Sold in twelve (12) foot strips only.
Side Roof Rail Weatherstrip
p/n: 30-0035-65
Weatherstrip, side window, rubber only. Fits in metal retainer as shown. Available by the foot.
Side Roof Rail Weatherstrip
p/n: 14-0001-80
Fifteen (15) foot strip for convertible side window fits aluminum retainer channel.
Side Roof Rail Weatherstrip
p/n: 20-2225-65
Seal, top iron to door glass. One (1) inch wide by thirty (30) inch length.
Side Roof Rail Weatherstrip
p/n: 70-0251-65
Weatherstrip, side window. Base fifteen sixteenths (15/16) inch wide but easily trims to more narrow channel if necessary.