Swing-Out Windshield Weatherstrip
p/n: 40-0018-52
This Swing-Out Windshield Weatherstrip comes in an eleven (11) foot strip. The seal slides into the track (channel) attached to the glass that goes all the way around the windshield and creates a seal when the glass is pressed against the body of the vehicle.
Windshield Division Bar Gasket
p/n: 70-0277-51
This inner and outer Windshield Division Bar Gasket is designed from the original part for superior fitment and function. This windshield center divider is molded with pilots and screw holes. Without a steel core.
Body to Frame Webbing
p/n: 20-1599-48
This Body to Frame Webbing is designed from the original part for superior fitment and function. This webbing is used to shim the body to the frame. Also used as a noise reducer material. Webbing is two (2) inch wide, twenty-five (25) foot long roll.
Body To Frame Mounting Pad Set
p/n: 20-2198-48
This is a thirty-four (34) piece Body To Frame Mounting Pad Set. Contains all the vehicle specific mounting pads to effectively cushion the body at the specific points to eliminate body rattles and squeaks.
Taillight Mounting Pad
p/n: 30-0201-15
Pads, taillight bracket mounting, with proper beading and shape. For two and one eighths (2-1/8) inch by five and one half (5-1/2) inch base. Length: 5.
Rear Stabilizer Bushing
p/n: 70-0406-33
Bushings, rear stabilizer. Comes as a four (4) piece set. Fully molded rubber.
Windshield Post To Door Weatherstrips
p/n: 20-2092-63
These Windshield Post To Door Weatherstrips attach to the body and seals between the windshield A-post and the front section of the door or vent window frame when the door is closed. Includes special molded foot. Fits one (1) inch wide channel.
Front Suspension Bumper
p/n: 50-0125-32
Bumper, front suspension, lower arm.Width: 2.625 inches. Height: 2.5625 inches.
Steering Column Collar Grommet
p/n: 70-0682-88
This Steering Column Collar Grommet is designed from the original part for superior fitment and function. The grommet fits the steering column at toe board over carpet.
Front Bumper Grommet
p/n: 27-0018-28
Grommet, front bumper. Fully detailed and flanged as original. Fully molded rubber.
Clutch and Brake Pedal Pads - Black
p/n: 40-0107-22
This reproduction Clutch and Brake Pedal Pad pair slips over the full perimeter of the brake pedal for a precise, factory fit. An oval style perfect reproduction to replace worn original pedal pads. Manufactured in Black rubber.
Torque Ball Boot
p/n: 25-0034-24
Cushion, propeller shaft (drive shaft) bearing.Height: 1.0625 inches.
Rear Bumper Grommet
p/n: 70-2231-29
Grommets, rear support arm. Fully molded with all original details.
Windshield Division Bar Gasket
p/n: 70-0309-51
Gaskets, windshield division channel, inner and outer, fully molded to include bolt holes and pilots. Two (2) piece set.
Brake and Clutch Pedal Pads
p/n: 30-0188-22
Pads, brake and clutch pedal, slip over type. Black rubber only. For black and red (semi-automatic clutch models) see our #30-0188-89.Length: 3.875 inches.
Sliding Quarter Window Seal
p/n: 60-0398-78
Weatherstrip, sliding quarter window. Mounted vertically in body where leading edge of sliding window fits when closed. Right & left rubber only.
Carpet Heel Plate
p/n: 40-0087-88
Heel pad for carpet. Identical to original. Five and three fourths (5-3/4) inch by ten and one half (10-1/2) inch, to be stitched in place.Length: 10.
Brown Steering Floorplate
p/n: 50-0260-89
Retainer, front floor mat on steering column (also called steering column floorplate). Brown rubber. For black see our #50-0260-36.
Clutch and Brake Pedal Pads - Black
p/n: 50-0049-22
This reproduction Clutch and Brake Pedal Pad pair slips over the full perimeter of the pedal for a precise, factory fit. A perfect reproduction to replace worn original pedal pads. Manufactured in quality black rubber.
Front Stabilizer Bushing
p/n: 70-0348-33
Bushings, front stabilizer bar mounting. Fully molded rubber. One and thirteen sixteenths inch (1 13/16") length by one and three eighths inch (1 3/8") width by eleven sixteenths inch (11/16") inside hole diameter by one and one half inch (1 1/2") height.
Rear Spring Bumper
p/n: 60-0137-32
Bumper, rear spring. Fits original retainer.Width: 2.5625 inches.
Prop shaft retainer bushing
p/n: 70-2268-27
Retainer, intermediate bearing. All models with two piece driveshafts.
Brake and Clutch Floor Plate
p/n: 18-0014-24
This Brake and Clutch Floor Plate is designed from the original part for superior fitment and seal. Fully molded in quality Black EPDM rubber. For Brown rubber see our #18-0014-89. Length: 7-1/2" inches.
Clutch and Brake Pedal Pads - Brown
p/n: 50-0049-89
This reproduction Clutch and Brake Pedal Pad pair slips over the full perimeter of the pedal for a precise, factory fit. A perfect reproduction to replace worn original pedal pads. Manufactured in quality black rubber.
Brake and Clutch Pedal Pads
p/n: 10-0176-22
This Brake and Clutch Pedal Pad pair is designed to slip-over a metal pedal core. These Pedal Pads are made with a high level of fit and finish to the elegant artistry of Ettore Bugatti.
Front Bumper Grommet
p/n: 27-0054-28
Grommet, front bumper. Fully molded rubber, detailed and flanged as original.
Side Window Beltline Scraper Weatherstrips
p/n: 60-0566-58
These inner and outer Side Window Beltline Scraper Weatherstrips slide into the groove on top of the door's window opening and wipes the glass when window is raised and lowered. Four (4) piece set.
Windshield Division Bar Gasket
p/n: 70-0247-51
Gasket set, windshield divider post, inner and outer. Two (2) piece set with screw holes and pilots.
Accelerator Pedal Service – Black
p/n: 70-1802-40
Revulcanization Service Only for Black Rubber Accelerator Pedal Pad. For Brown see our 70-1802-89.
Bumper Grommet
p/n: 30-0039-28
Grommets, front or rear bumper. On models without trunk racks. Two (2) pair used per car if needing both front and rear bumper grommets.
Rear Axle Bumpers
p/n: 70-0210-32
This Rear Axle Bumper pair is a quality reproduction of the original factory part. These bottoming pads are dense rubber blocks that mount by bracket to the rear axle tube.
Front Bumper Grommet
p/n: 60-0080-28
Grommets, front bumper, right and left. Hollow construction as original. Fully molded rubber.
Front Axle Bumpers
p/n: 20-2175-33
This Front Axle Bumper pair is designed from the original part for an authentic fit, finish and function.
Taillight Mounting Pad
p/n: 70-1110-15
Spacer, taillight and license light bracket to body. Right hand. For the left hand version see our #70-1109-15.Length: 4.5 inches.
Red Brake and Clutch Pedal Pad
p/n: 30-0188-89
Pads, brake and clutch pedal, slip over type. Black and red rubber. For black only see our #30-0188-22.Length: 3.875 inches. Width: 2.875 inches.
Fender Skirt Edge Weatherstrips
p/n: 70-0055-45
This Fender Skirt Edge Weatherstrip pair is designed from the original part for superior fitment, finish and sealing function. Two five (5) foot strips that fit between the rear wheel fender skirt and rear quarter panel.
Rear Bumper Grommet
p/n: 40-0363-30
Grommet, rear bumper to body, right and left. Fully molded rubber.
Taillight Mounting Pad
p/n: 30-0132-15
Pads, taillight bracket mounting, with proper beading.Length: 6.625 inches.
Brake and Clutch Pedal Pads - Brown
p/n: 40-0107-89
This reproduction Clutch and Brake Pedal Pad pair slips over the full perimeter of the brake pedal for a precise, factory fit. An oval style perfect reproduction to replace worn original pedal pads. Manufactured in Brown rubber.
Taillight Mounting Pad
p/n: 40-0185-15
Pad, taillight mounting.Length: 8.8125 inches. Width: 3.875 inches.
Accelerator Pedal Service – Brown
p/n: 70-1802-89
Revulcanization Service Only for Brown Rubber Accelerator Pedal Pad. For Black see our 70-1802-40.
Accelerator Pedal Service, Brown
p/n: 70-1777-89
Accelerator pedal, Brown. Revulcanization service only.
Accelerator Pedal Service - Brown
p/n: 25-0067-89
Revulcanization Service Only for Brown Rubber Accelerator Pedal Pad. For Black see our #25-0067-40.
Stabilizer Bushing
p/n: 60-0316-34
Bushing, front stabilizer shaft. Two (2) per car.Length: 1.875 inches. Width: 1.6875 inches. Height: 1.4375 inches.
Detachable Center Post Pad
p/n: 70-0280-88
Pads, folding front seat rest, brass core. Also used as bumper, slat iron to compartment on convertibles.
Brown Brake and Clutch Floor Plate
p/n: 18-0014-89
This Brake and Clutch Floor Plate is designed from the original part for superior fitment and seal. Fully molded in quality Brown EPDM rubber. For Black rubber see our #18-0014-24.
Windshield Division Bar Gasket
p/n: 30-0146-52
Gasket, windshield division bar. Molded inner and outer, fully detailed.Length: 13.625 inches.
Chrome Fender Welting - 50ft
p/n: 70-1102-44
Welting, fender, bright chrome vinyl, three sixteenths (3/16) inch bead, one and one half (1-1/2) inch width. Superior quality. Fifty (50) foot roll. Typically used to attach four (4) fenders to body. For twenty five (25) foot roll see #70-1101-44.
Fender Welting 1/4" Bead - 50ft
p/n: 70-1098-44
Welting, fender. Superior quality, proper construction of reinforced black vinyl over vinyl core, one and three eighths (1-3/8) inch wide. One fourth (1/4) inch bead, fifty (50) foot roll. Typically used to attach four (4) fenders to body.
Fender Welting with 3/16" Bead - 50ft
p/n: 70-1100-44
A superior quality Fender Welting material constructed of reinforced black vinyl over a vinyl core. Typically used for attaching four (4) fenders to body. Sold in a 50 foot roll.
Brake and Clutch Pedal Pads - Brown
p/n: 40-0121-89
This reproduction Clutch and Brake Pedal Pad pair slips over the full perimeter of the brake pedal for a precise, factory fit. An oval style perfect reproduction to replace worn original pedal pads. Manufactured in Brown rubber.
Swing-Out Windshield Weatherstrip
p/n: 60-0447-50
This Swing-Out Windshield Weatherstrip is designed from the original part. The seal mounts into the track (channel) attached to the glass that goes all the way around the windshield and creates a seal when the glass is pressed against the body of the vehicle.
Engine Mount Pad
p/n: 30-0238-11
This Engine Mount Pad pair is used as a support cushion at the timing gear cover. Correct design and rubber compound. Sold only in pairs. One (1) pair required per car.
Engine Mount Pad
p/n: 30-0331-11
This Engine Mount Pad pair is used as a support at the timing gear cover. One (1) pair required per car. Sold only in pairs.
Rear Bumper Grommet
p/n: 30-0067-29
Grommets, rear bumper. Length: 4.3125 inches. Width: 2.6875 inches.
Spare wheel carrier grommet
p/n: 30-0334-37
Grommet, rear spare wheel carrier bracket. Two (2) per car. (Also order our #32-0355-37 separately).
Windshield Division Bar Gasket
p/n: 60-0128-52
This two (2) piece Windshield Division Bar Gasket set is designed from the original part for superior fitment and function. Inner and outer windshield division bar molding retainer. With threaded brass core as original (molding not included).
Rear window division bar seal
p/n: 70-0246-82
Gasket set, back window divider post. Inner and outer, with mounting holes. Four (4) piece set.
Gearshift Seal
p/n: 30-0165-24
Seal, gearshift to floorboard.Length: 5.625 inches. Width: 4.875 inches.
Stabilizer Bushing
p/n: 30-0484-33
Bearings, stabilizer front rod. Requires two (2) per car. Fully molded rubber.
Trunk Weatherstrip
p/n: 70-1129-84
This Trunk Weatherstrip is designed from the original part for superior fitment and seal. The seal mounts around the full perimeter of the trunk lid.
Accelerator Pedal Service, Black
p/n: 70-1777-40
Accelerator pedal, black. Revulcanization service only.
Rigid Run Channel
p/n: 30-0180-57
Channel, rigid run, for vent window division bar. Chrome beaded edge, mohair lined steel channel to proper dimensions for window side of wing window frame.
Accelerator Pedal Service
p/n: 30-0400-41
Revulcanization Service Only for Black Rubber Accelerator Pedal Pad. Includes new ball sockets as original, with correctly detailed tread pattern.
Front Bumper Grommet
p/n: 70-0291-28
Grommets, front bumper arm. Hollow construction for good fit. Fully molded rubber.
Plug Wire Sleeve
p/n: 30-0204-21
Sleeve, plug wire tube to distributor cap. One (1) pair required per car.Height: .9375 inches.
Cadillac V-8 Pedal Pad
p/n: 70-0148-22
Cadillac V-8 pedal pads, clutch and brake. Another rare one we finally found to copy. Superior copy.
Hood Corner Pad
p/n: 30-0010-42
Pads, hood rear corners. High quality rubber with metal core as original.Length: 3.4375 inches. Width: 1.875 inches.
Stabilizer Bushing
p/n: 30-0483-33
Bearings, stabilizer rear rod. Requires two (2) per car. Fully molded rubber.
Hood Corner Pad
p/n: 30-0088-42
Pad, hood front corner. Metal core, retained by four (4) tabs.Length: 3.25 inches. Width: 1.25 inches.
Rigid Run Channels
p/n: 70-0536-58
A Rigid Run Channel pair with bright beaded edge, mohair lined channel, die trimmed and round formed at the top. Sold in 29" pairs.
Windshield Division Bar Gasket
p/n: 27-0017-51
This inner and outer Windshield Division Bar Gasket is designed from the original part for superior fitment and function. With tapped brass core, sixteen (16) inches long. For models without division bar strainer built into body.
Lower Suspension Arm Dust Seal Set
p/n: 70-0865-32
This four (4) piece Lower Suspension Arm Dust Seal Set is fully molded of high-quality EPDM dense rubber for durability and proper fitment. These seals are used to protect your lower suspension arm bushings from dust and debris.
Transmission Mounting Pad
p/n: 50-0335-25
Transmission support pad, insulator blocks, upper and lower.
Coil wire sleeve
p/n: 14-0022-21
Sleeve, spark plug wires from distributor to wiring tube, rubber only.
Trunk Weatherstrip
p/n: 70-1128-84
This Trunk Weatherstrip is designed from the original part for superior fitment and seal. The seal mounts around the full perimeter of the trunk lid.
Front Spring Bumpers
p/n: 30-0087-32
This Front Spring Bumper pair is a quality reproduction of the original factory part. Self retaining type bumper manufactured with top quality materials.
Trunk Weatherstrip
p/n: 20-2267-84
This Trunk Weatherstrip is designed from the original part for superior fitment and seal. The seal mounts around the full perimeter of the trunk directly to the body.
Front Bumper Grommet
p/n: 40-0077-30
Grommet, front bumper. Hollow construction for good fit as original.Length: 3.5625 inches.