Accelerator Pedal Pad
p/n: 60-0430-40
Cover, accelerator pedal. Exact pattern of original. Slipover type. Use your old steel core. Length: 7.875 inches.
Fender Welting with 3/16 Bead - 25ft
p/n: 70-1099-44
A superior quality Fender Welting material constructed of reinforced black vinyl over a vinyl core. Typically used for attaching two (2) fenders to body. Sold in a 25 foot roll.
Rumble Seat Step Mounting Pad
p/n: 30-0181-44
Pad, rumble seat step bracket to fender. Four and one fourth (4-1/4) inch long.Length: 4.375 inches.
Wiring Grommet
p/n: 70-0709-21
Grommet, horn wire exit from horn motor cover. Eleven thirty seconds (11/32) inch inside diameter. Two (2) per car.
Brake and clutch shank seal
p/n: 60-0019-24
Seal, brake and clutch pedal shank to floorboard. Single bellows rubber cup, seals air drafts around pedals.
Front Bumper Seal
p/n: 70-1103-28
Seals, front bumper. Fully molded rubber, U-shaped. Three and one half inches (3-1/2") long by three and one half inches (3-1/2") wide by thirteen sixteenths inch (13/16") height. For the grommets see our #70-1104-28, sold separately.
Flexible Run Channel - 5ft
p/n: 70-1107-57
Cloth covered mohair-lined type. For sides and top of side windows. Available in 5ft lengths.
Door Weatherstrip
p/n: 40-0367-57
Door belt inner weatherstrip (scraper seal). Front door only. Thirty six (36) inches long.
Horn button contact cushion
p/n: 50-0409-21
Separator, horn contact. For standard or non-flexible wheel.
Fuel Filler Neck Grommet
p/n: 60-0040-41
This Fuel Filler Neck Grommet is a fully molded rubber, grommet slightly angled with a retaining flange. Three and five sixteenths inch (3-5/16") outside width by three and one half inch (3-1/2") outside length by two and one eighth inch (2-1/8") inside hole diameter.
Detachable Center Post Pad
p/n: 30-0422-67
Pad, convertible top center latch. Excellent workmanship with metal insert like original.
Rumble Seat Lid Corner Pad
p/n: 70-0152-87
Pads, rumble seat lid corners, original rounded triangle shape.Length: 1.5 inches. Width: .4375 inches.
Firewall Grommet
p/n: 70-0223-20
This Firewall Grommet is used on the lower end of the elbow from the firewall to the voltage regulator. Designed from the original part for superior fit and seal.
Rumble Seat Step Mounting Pad
p/n: 50-0182-44
Mounting pad, rumble seat step to fender, proper beaded edge, exact copy.Width: 4.8125 inches.
Headlight Mounting Stand Pads
p/n: 20-0316-14
This Headlight Mounting Stand Pad pair is designed from the original part for an authentic fit, finish, and appearance. These mounting pads fit between the headlight stands and the front fenders.
Cowl vent weatherstrip
p/n: 70-0143-54
Gasket, cowl vent. Perfect copy of original, not a sponge substitute, top quality material.
Rear Engine Mount
p/n: 70-0648-11
This Rear Engine Mount is used as an upper and lower support bracket at the transmission. Made from high-quality EPDM rubber for a precise, factory like fit.
Radio Antenna End Loop
p/n: 70-0105-21
End loop, radio antenna. Cord reinforced rubber with metal grommet. Mounted on running board on some models.