Cowl Vent Gasket
p/n: 30-0172-54
Gasket, cowl vent. Top quality sponge of correct section, cut to sufficient length for circumference of vent cover.
Wiring Grommet
p/n: 70-0709-21
Grommet, horn wire exit from horn motor cover. Eleven thirty seconds (11/32) inch inside diameter. Two (2) per car.
Hood Bumper
p/n: 30-0080-42
Bumper, inner hood rest. Good copy and material. One (1) pair required per car.Length: 1.50 inches. Width: .875 inches.
Rear Leaf Spring Bushings
p/n: 70-0663-32
This Rear Leaf Spring Bushing pair is designed from the original part for superior fitment and function. Busing are for the rear leaf spring front or rear spring eyes.
Brake and clutch shank seal
p/n: 60-0019-24
Seal, brake and clutch pedal shank to floorboard. Single bellows rubber cup, seals air drafts around pedals.
Flexible Run Channel - 5ft
p/n: 70-1107-57
Cloth covered mohair-lined type. For sides and top of side windows. Available in 5ft lengths.
Trunk Lid Clamp Mounting Pad
p/n: 30-0182-87
Pads, trunk lid hasp (clamp) mounting. Fine beaded edge, perfect copy. These are not hinge pads. Four (4) piece set.Length: 4.0 inches. Width: 1.0 inches.
Brake and clutch pedal bumper
p/n: 30-0380-20
Bumper, inclined toe board pedal hole, carried on toe board to meet our #30-0055-24 pedal. dust cover.
Trunk Weatherstrip
p/n: 20-2126-84
This Trunk Weatherstrip is designed from the original part for superior fitment and seal. The seal mounts around the full perimeter of the trunk directly to the body.
Firewall Grommet
p/n: 70-0223-20
This Firewall Grommet is used on the lower end of the elbow from the firewall to the voltage regulator. Designed from the original part for superior fit and seal.
Side Window Sash Channel
p/n: 70-0641-58
This Side Window Sash Channel is the u-shaped steel channel only, no filler. Sold in 4 foot strip, usually sufficient for two (2) windows.
Headlight Mounting Pad
p/n: 60-0558-14
Pad, headlight bracket at fender. See also our #60-0178-14. Two and one eighth (2-1/8) inch by three and seven sixteenths (3-7/16) inch.Length: 3.
Rumble Seat Step Mounting Pad
p/n: 25-0019-44
Mounting pad for our #25-0018-44 fender step. Length: 7.375 inches.
Fuel Neck Grommet
p/n: 60-0336-41
Grommet, fuel filler neck. Fully molded rubber. Three and fifteen sixteenths inch (3-15/16") outside diameter by two and one sixteenth inch (2-1/6") top hole diameter by two and three sixteenths inch (2-3/16") bottom hole diameter.
Cowl vent weatherstrip
p/n: 70-0143-54
Gasket, cowl vent. Perfect copy of original, not a sponge substitute, top quality material.
Rear Engine Mount
p/n: 70-0648-11
This Rear Engine Mount is used as an upper and lower support bracket at the transmission. Made from high-quality EPDM rubber for a precise, factory like fit.
Radio Antenna End Loop
p/n: 70-0105-21
End loop, radio antenna. Cord reinforced rubber with metal grommet. Mounted on running board on some models.
Brake and Clutch Shank Seal
p/n: 40-0175-24
Seal, brake and clutch pedal shank to floorboard. One and one half (1-1/2) inch by two and one eighth (2-1/8) inch by three fourths (3/4) inch thick.
Convertible Post Bumper
p/n: 30-0409-67
Bumper, convertible top side roof rail, center. Two (2) per car.
Rear Window Division Bar Seal
p/n: 40-0285-77
Gasket, back window division bar. Closed body styles with split back window.Length: 9.25 inches. Width: 1.125 inches.
Brake and Clutch Shank Seal
p/n: 30-0055-24
Seals, brake and clutch pedal shanks, against underside of floorboard.Length: 2.5625 inches. Width: 1.75 inches.