Brown Steering Column Grommet
p/n: 27-0047-89
Grommet, steering column at toe board. Brown rubber.Color:brown Length: 3.50 inches.
Brown Steering Floorplate
p/n: 50-0260-89
Retainer, front floor mat on steering column (also called steering column floorplate). Brown rubber. For black see our #50-0260-36.
Bumper Grommet
p/n: 30-0039-28
Grommets, front or rear bumper. On models without trunk racks. Two (2) pair used per car if needing both front and rear bumper grommets.
Cadillac Motors pedal pad
p/n: 70-0076-22
Cadillac Motors pedal pads. Authentic straight diamond pattern. Especially good copy, fine detail.
Cadillac V-8 Pedal Pad
p/n: 70-0148-22
Cadillac V-8 pedal pads, clutch and brake. Another rare one we finally found to copy. Superior copy.
Carpet Heel Plate
p/n: 40-0087-88
Heel pad for carpet. Identical to original. Five and three fourths (5-3/4) inch by ten and one half (10-1/2) inch, to be stitched in place.Length: 10.
Channel Filler Weatherstrip
p/n: 20-1633-62
Seal, door glass and stainless frame special. Top, bottom, and sides for one door.Width: .375 inches. Height: .625 inches.
Choke and Throttle Dash Grommets
p/n: 20-0347-41
This Choke and Throttle Dash Grommet pair mounts in the dash where the choke and throttle rods pass through the dash to keep rods from rattling.
Choke and Throttle Grommet
p/n: 20-2280-88
This Choke and Throttle Grommet pair is the original style grommet. The grommets are a molded rubber encased in a metal sleeve. The pair includes the mounting clips.
Choke and Throttle Rod Grommet
p/n: 20-2279-88
This Choke and Throttle Rod Grommet is used where the choke and throttle pass through the dash. Designed from the original part for superior fit and seal.
Choke, Throttle and Starter Wiper Motor Grommet
p/n: 20-1561-20
This Choke, Throttle or Wiper Motor Grommet is designed from the original part for superior fitment and usage. A multi-purpose grommet, it fits into the vehicles firewall to provide a secure passthrough for the mechanical choke, throttle rod or wiper motor wiring.
Chrome Fender Welting - 25ft
p/n: 70-1101-44
Welting, fender, bright chrome vinyl, three sixteenths (3/16) inch bead, one and one half (1-1/2) inch width. Superior quality. Twenty five (25) foot roll. Typically used to attach two (2) fenders to body. For fifty (50) foot roll see our #70-1102-44.
Chrome Fender Welting - 50ft
p/n: 70-1102-44
Welting, fender, bright chrome vinyl, three sixteenths (3/16) inch bead, one and one half (1-1/2) inch width. Superior quality. Fifty (50) foot roll. Typically used to attach four (4) fenders to body. For twenty five (25) foot roll see #70-1101-44.
Chrome Molding Washer
p/n: 60-0727-45
Washer, for attaching chrome moldings on body. Fits into metal cup retainer. Three fourths (3/4) inch diameter, use as required.
Clutch and Brake Pedal Arm Seals
p/n: 20-1564-23
This Clutch and Brake Pedal Arm Seal pair is designed from the original part for an authentic fit, finish, and appearance. For Clutch and Brake pedal arms to floorboard.
Clutch and Brake Pedal Bump Stops
p/n: 70-4805-24
This Clutch and Brake Pedal Bump Stop pair is designed from the original part for superior fitment, finish and function. These rubber bumpers help align your brake and clutch pedals in the correct position, while also preventing rattles and squeaks.
Clutch and Brake Pedal Bumpers
p/n: 60-0104-24
This Clutch and Brake Pedal Bumper is designed from the original part for superior fitment, finish and function. Pedal shank rides under floorboard. One and one-eighth (1-1/8") inch clearance for pedal shaft.
Clutch and Brake Pedal Pads
p/n: 60-0068-22
This reproduction Clutch and Brake Pedal Pad pair slips over the full perimeter of the pedal for a precise, factory fit. An oval style perfect reproduction to replace worn or damaged original pedal pads.
Clutch and Brake Pedal Pads - Black
p/n: 50-0049-22
This reproduction Clutch and Brake Pedal Pad pair slips over the full perimeter of the pedal for a precise, factory fit. A perfect reproduction to replace worn original pedal pads. Manufactured in quality black rubber.
Clutch and Brake Pedal Pads - BLACK
p/n: 25-0024-22
This reproduction Clutch and Brake Pedal Pad pair slips over the full perimeter of the brake pedal for a precise, factory fit. A reproduction with authentic type ribbing, to replace worn original pedal pads. Manufactured in Black rubber.
Clutch and Brake Pedal Pads - Black
p/n: 50-0054-22
This reproduction Clutch and Brake Pedal Pad pair slips over the full perimeter of the pedal for a precise, factory fit. A perfect reproduction to replace worn original pedal pads. Manufactured in quality black rubber.
Clutch and Brake Pedal Pads - Black
p/n: 40-0107-22
This reproduction Clutch and Brake Pedal Pad pair slips over the full perimeter of the brake pedal for a precise, factory fit. An oval style perfect reproduction to replace worn original pedal pads. Manufactured in Black rubber.
Clutch and Brake Pedal Pads - Bowtie Emblem
p/n: 60-0125-22
This reproduction Clutch and Brake Pedal Pad pair slips over the full perimeter of the pedal for a precise, factory fit. A perfect reproduction to replace worn original pedal pads. Manufactured in quality black rubber with Chevy bowtie in tread.
Clutch and Brake Pedal Pads - Brown
p/n: 50-0049-89
This reproduction Clutch and Brake Pedal Pad pair slips over the full perimeter of the pedal for a precise, factory fit. A perfect reproduction to replace worn original pedal pads. Manufactured in quality black rubber.
Clutch and Brake Pedal Pads - Brown
p/n: 50-0054-89
This reproduction Clutch and Brake Pedal Pad pair slips over the full perimeter of the pedal for a precise, factory fit. A perfect reproduction to replace worn original pedal pads. Manufactured in quality brown rubber.
Clutch and Brake Pedal Pads - BROWN
p/n: 25-0024-89
This reproduction Clutch and Brake Pedal Pad pair slips over the full perimeter of the brake pedal for a precise, factory fit. A reproduction with authentic type ribbing, to replace worn original pedal pads. Manufactured in Brown rubber.
Clutch pedal bumper
p/n: 60-0355-24
Bumper, clutch pedal shank under floorboard. Some commercial and utility models, compare with our #60-0104-24.
Coil spring insulator pad
p/n: 70-0801-32
Pad, coil spring insulator. Molded four (4) piece set for one (1) car.
Coil wire sleeve
p/n: 70-1179-21
Sleeve, coil wire to distributor. Fluted to match upper water hoses rubber only.
Coil wire sleeve
p/n: 14-0022-21
Sleeve, spark plug wires from distributor to wiring tube, rubber only.
Control Arms Cross-Shaft Bushing Seal
p/n: 60-0094-32
This Control Arms Cross-Shaft Bushing Seal is designed from the original part for superior fitment and seal. Installs at upper and lower control arm cross shaft bushing, at inner end of control arm.
Convertible Front Header Bow Weatherstrip
p/n: 70-0138-64
This convertible soft top Front Header Bow Weatherstrip is designed from the original part for superior fitment and seal. This seal installs directly to the convertible soft top to seal to the windshield, OUTER, right and left. This weatherstrip is molded with necessary pre-drilled end hook and screw openings to the proper clearance.
Convertible Front Header Bow Weatherstrip
p/n: 70-0157-64
This convertible soft top Front Header Bow Weatherstrip is designed from the original part for superior fitment and seal. This seal installs directly to the convertible soft top to seal to the windshield, INNER, right and left.
Convertible Roof Rail Weatherstrip
p/n: 20-1636-65
This Convertible Roof Rail Weatherstrip is designed from the original part for superior fitment and seal. This window channel seal fits between windshield posts and door. Also fits along the top irons. This part is one (1) each. Five (5) individual pieces are required for the complete top.
Convertible Top Front Bow Weatherstrip
p/n: 70-0100-64
This Convertible Top Front Bow Weatherstrip is designed from the original part for superior fitment and seal. This header seal installs directly to the windshield frame to seal between the soft top and the top of the windshield.
Cowl Firewall Grommet
p/n: 20-1560-20
This Cowl Firewall Grommet fits into the upper section of the firewall for the main wiring harness. Also used to run the dash wires on the firewall and through the firewall.
Cowl Vent Gasket
p/n: 30-0519-54
Gasket, cowl vent. Die cut sponge with smooth curves. Excellent reproduction designed to fit in gutter and not bind when closing.Length: 15.75 inches.
Cowl Vent Gasket
p/n: 40-0271-54
Gasket, cowl vent. Fully molded to original cross-section and outline.Length: 18.0 inches.
Cowl Vent Gasket
p/n: 14-0037-54
Gasket stock, cowl vent, high grade sponge of proper cross-section, (not molded into ring), approximately forty eight (48) inch strip per car.
Cowl Vent Gasket
p/n: 70-0194-54
Gasket, cowl vent. Original solid rubber configuration, not a sponge substitute.
Cowl Vent Gasket
p/n: 60-0081-54
Gasket, cowl vent. These parts are made of the highest quality and authenticity.Length: 15.0 inches.
Cowl Vent Gasket
p/n: 30-0050-54
Gasket, cowl vent. Perfect reproduction, high quality, original configuration, not a sponge substitute.Length: 14.0 inches. Width: 5.75 inches.
Cowl Vent Gasket
p/n: 20-1613-54
This Cowl Vent Gasket is designed from the original part for superior fitment and seal. Manufactured to OEM specifications to install for an authentic fit and finish.
Cowl vent weatherstrip
p/n: 70-0143-54
Gasket, cowl vent. Perfect copy of original, not a sponge substitute, top quality material.
Crankshaft Vibration Damper - Revulcanization Only
p/n: 30-0376-12
This Revulcanization Service Only is designed to restore the Crankshaft Vibration Damper to a like new original condition. This revulcanizing service is for the rubber cushion elements. Service requires your metal core.
Detachable Center Post Pad
p/n: 30-0261-67
Pad set, detachable center post, folding top upper and lower, right and left. Steel cores as original. 4 piece set.Width: 3.0 inches. Height: 2.75 inches.
Detachable Center Post Pad
p/n: 30-0286-67
Pads, lower, top removable center pillar, right and left. Brass core.Width: 3.375 inches. Height: 2.75 inches.
Detachable Center Post Pad
p/n: 30-0422-67
Pad, convertible top center latch. Excellent workmanship with metal insert like original.
Detachable Center Post Pad
p/n: 70-0280-88
Pads, folding front seat rest, brass core. Also used as bumper, slat iron to compartment on convertibles.
Detachable Center Post Pad
p/n: 70-0273-67
Pads, upper and lower for removable center post, brass carcass as original. Four (4) piece set.Length: 3.125 inches.
Detachable Center Post Pad
p/n: 70-0295-67
Pads, detachable center post, upper and lower, steel core. One and nine sixteenths (1-9/16) inches by four and one fourth (4-1/4) inches. Four (4) piece set.
Detachable Center Post Pad
p/n: 70-0445-66
Pads, detachable center post, upper and lower, right and left, brass core, four (4) piece set.Length: 4.375 inches. Width: 1.625 inches.
Detachable Center Post Pad
p/n: 30-0287-67
Pads, convertible top folding pillar (top main bow hinge), right and left, with brass core.
Detachable center post pad
p/n: 20-2227-66
Pads, center pillar post. Two (2) upper and two (2) lower in set.
Dimmer Switch Grommet
p/n: 40-0083-88
This Dimmer Switch Grommet is used during carpet installations in automotive restorations. Made from high-quality EPDM dense rubber to provide excellent durability. Includes a wide flange for floor dimmer switch fitments.
Door - Gravel Shield - Running Board Weatherstrip
p/n: 60-0054-73
This Door - Gravel Shield - Running Board Weatherstrip is a anti-squeak bulb type extrusion with fitment for General Motors vehicles. A twelve (12) foot strip made of high-quality EPDM dense rubber and designed from original parts for superior fitment, finish and function.
Door - Upper Weatherstrip
p/n: 70-0063-73
Door - Upper Weatherstrip - The upper and inner door weatherstrip on the body. Hollow rubber seal, fits metal retainer as original. Set of four (4) strips, five (5) foot long per strip.
Door Alignment Pad
p/n: 70-1821-71
Wedge pads, door aligning.Length: 1.125 inches. Width: .5 inches. Height: .875 inches.
Door and Trunk Handle Gasket
p/n: 40-0132-70
Pad, door handle escutcheon. Two and five sixteenths (2-5/16) inch by one and seven sixteenths (1-7/16) inch.
Door Bottom weatherstrip
p/n: 70-3140-73
Seal, lower door. Mounts to door scuff plates. Enough for 4 doors.
Door Bumper
p/n: 34-0131-37
Bumper, front door above the upper hinge on the upper radius of the door. Stiff-backed, retained by screw, mounted on door only.
Door Bumper
p/n: 70-0168-71
Bumper, door side. Square type held by four (4) screws, metal core as original.