Brake and Clutch Shank Seal
p/n: 40-0217-24
Draft cap for brake and clutch pedal.Length: 2.4375 inches. Width: 1.6875 inches.
Brake and clutch shank seal
p/n: 70-0156-23
Grommet, brake and clutch pedal shank at toe board. Flange retained, perfect copy.
Convertible Top - Resting Block
p/n: 20-2231-67
Pad, convertible top resting block. Used when top is down. One (1) required per vehicle.
Flexible Run Channel
p/n: 70-1239-58
This Flexible Run Channel provides a smooth sliding surface while helping to eliminate rattle and protect the glass. The run channel has the stainless beaded edge and is cloth covered and mohair lined with the flexible metal channel.
Taillight Mounting Pad
p/n: 40-0172-15
Pad, taillight bracket mounting. Right and left, plain pad without beading as original. Length: 5.3125 inches.
Engine Mount Pad
p/n: 11-0026-11
This Engine Mount Pad is designed to original pattern with superior workmanship. Made from high-quality EPDM rubber for a precise, factory like fit. Two (2) required per car.
Door Bottom weatherstrip
p/n: 70-3140-73
Seal, lower door. Mounts to door scuff plates. Enough for 4 doors.
Trunk Weatherstrip
p/n: 20-2266-84
This Trunk Weatherstrip is designed from the original part for superior fitment and seal. The seal mounts around the full perimeter of the trunk directly to the body.
Vent division bar weatherstrip
p/n: 30-0461-56
Front vent window division post seal. Fully molded with metal core and attaching tabs.
Cowl Vent Weatherstrip
p/n: 70-0224-54
Weatherstrip, cowl vent. Original solid rubber configuration, not a sponge substitute. A top quality part for your classic vehicle restoration.
Gearshift Boot
p/n: 40-0111-88
Boot, base of gearshift lever. Black rubber. For brown see our #40-0111-89. Made separately to fit most of our gearshift floorplates. Copied from original.
License Light Mounting Pad
p/n: 40-0135-17
Pad, license light mounting.Length: 5.25 inches. Width: 3.875 inches.
Rumble Seat Step Mounting Pad
p/n: 30-0271-44
Gasket, rumble seat step center. Length: 5.875 inches.
Vent division bar weatherstrip
p/n: 70-0791-56
Front vent window division post seal. Fully molded with metal core and attaching tabs.
Vent Window Division Bar Weatherstrips
p/n: 50-0332-56
This Front Vent Window Division Bar / Post Weatherstrip pair is designed from the original part for superior fitment and seal. This piece mounts on the vertical division bar and seals as the vent glass closes against it.
Vent Window Division Post Weatherstrips
p/n: 60-0596-56
This Front Window Vent Division Post Weatherstrip pair is fully molded with metal core and attaching tabs.
Window Felt Beltline Weatherstrips
p/n: 70-0555-58
These Window Felt Beltline Weatherstrips are sold as a three (3) foot pair. The beltline is used for side windows inner and/or outer, front and/or rear doors. Available in a 3ft pair.
Vent Division Bar Weatherstrip
p/n: 70-0695-74
Division bar seal. Proper cross section rubber molded to original style metal with authentic attaching tabs.
Convertible Top - Rest Block
p/n: 50-0318-67
Rest block, convertible top. Two (2) required per car. Fits into dovetail retainer. Length: 1.375 inches. Width: 1.125 inches.
Brown Gearshift Boot
p/n: 50-0035-89
Boot, gearshift. Brown rubber. For black see our #50-0035-24.Color:brown Width: 2.8125 inches.
Brake and Clutch Shank Seal
p/n: 30-0143-24
Boot, brake and clutch pedal shank at toe board.Length: 2.9375 inches.
Hood To Radiator Weatherstrip
p/n: 60-0111-42
This Hood To Radiator Weatherstrip is molded with four (4) self retaining carrots for easy installation. Sold as a pair for the left and right sides.
Rear spring bushing
p/n: 60-0311-35
Bushing, rear spring front eye, inlox cartridge type as original.
Trunk Hinge Mounting Pad
p/n: 50-0106-87
Mounting pads, trunk hinge, four (4) piece set. Models with outside hinges.Length: 8.25 inches.
Clutch and Brake Pedal Pads - Brown
p/n: 50-0054-89
This reproduction Clutch and Brake Pedal Pad pair slips over the full perimeter of the pedal for a precise, factory fit. A perfect reproduction to replace worn original pedal pads. Manufactured in quality brown rubber.
Flexible Run Channel
p/n: 70-1238-58
Cloth covered, mohair lined flexible metal channel for sides and top of door windows.
Accelerator Pedal Pad
p/n: 60-0097-40
Pad, accelerator pedal. Slip-over type for original core. Length: 9.125 inches.
Quarter Window Weatherstrips
p/n: 20-2376-77
This Quarter Window Weatherstrip pair is designed from the original part for superior fitment and sealing. Ends are pre-bonded together.
Rear Window Gasket Set
p/n: 20-2261-81
This Rear Window Gasket Set mounts around the two (2) separate back windows. They have vulcanized, or bonded, ends which means no cutting or splicing is required for installation.
Trunk or Rumble Seat Weatherstrip Set
p/n: 20-2127-84
This Trunk or Rumble Seat Weatherstrip Set is designed from the original parts for superior fitment and seal. The set includes the strip that mounts to the body and the strip that mounts to the lid.
Windshield Weatherstrip
p/n: 20-2203-50
This Windshield weatherstrip gasket is a fully molded rubber channel for installing front window glass. Seals windshield glass to body and protects interior of vehicle. All corners are correctly molded to fit perfectly.
Chrome Fender Welting - 25ft
p/n: 70-1101-44
Welting, fender, bright chrome vinyl, three sixteenths (3/16) inch bead, one and one half (1-1/2) inch width. Superior quality. Twenty five (25) foot roll. Typically used to attach two (2) fenders to body. For fifty (50) foot roll see our #70-1102-44.
Fender Welting 1/4" Bead - 25ft
p/n: 70-1097-44
Welting, fender. Superior quality, proper construction of reinforced vinyl over vinyl core, one and three eighths (1-3/8) inch wide, black only. One fourth (1/4) inch bead, twenty-five (25) foot roll. Typically used to attach two (2) fenders to body.
Sliding Quarter Window Weatherstrip
p/n: 70-0353-78
This Sliding Quarter Window Weatherstrip is used for side window inner and/or outer, front and/or rear doors. Available in a 6ft. lengths.
Trunk Hinge Mounting Pad
p/n: 70-1229-87
Mounting pad, trunk hinge. Four (4) piece set.Length: 7.625 inches.
Rumble Seat Step Mounting Pad
p/n: 30-0272-44
Gasket, rumble seat step. For left hand drive upper. Length: 5.0 inches.
Headlight Mounting Pad
p/n: 60-0115-14
Pad, headlight support bracket. Two and one half (2-1/2) inch by six and one fourth (6-1/4) inch.Length: 6.25 inches. Width: 2.5 inches.
Window Felt Beltline Weatherstrips - 3ft Pair
p/n: 30-0244-57
This side window Window Felt Beltline Weatherstrip pair can be used as inner and/or outer. The weatherstrip is flexible, pile lined, rubber covered, with black bead. Available in 3ft pairs.
Accelerator Rod Seal
p/n: 60-0136-41
Grommet, accelerator rod through toe board. Brass core and center bushing as original.
Rumble Seat Lid Bumper Pad
p/n: 70-0278-87
Side pads, rumble seat lid, right and left. Length: 1.125 inches. Width: .6875 inches.
Accelerator Pedal Pad
p/n: 60-0430-40
Cover, accelerator pedal. Exact pattern of original. Slipover type. Use your old steel core. Length: 7.875 inches.
Cowl Vent Gasket
p/n: 30-0172-54
Gasket, cowl vent. Top quality sponge of correct section, cut to sufficient length for circumference of vent cover.
Fender Welting with 3/16 Bead - 25ft
p/n: 70-1099-44
A superior quality Fender Welting material constructed of reinforced black vinyl over a vinyl core. Typically used for attaching two (2) fenders to body. Sold in a 25 foot roll.
Hood Bumper
p/n: 30-0080-42
Bumper, inner hood rest. Good copy and material. One (1) pair required per car.Length: 1.50 inches. Width: .875 inches.
Rumble Seat Lid Bumper Pad
p/n: 30-0275-44
Bumpers, rumble seat stop bracket. Self-retaining type as original.Length: 1.1875 inches. Width: .75 inches. Height: .375 inches.
Rumble Seat Step Mounting Pad
p/n: 30-0181-44
Pad, rumble seat step bracket to fender. Four and one fourth (4-1/4) inch long.Length: 4.375 inches.
Wiring Grommet
p/n: 70-0709-21
Grommet, horn wire exit from horn motor cover. Eleven thirty seconds (11/32) inch inside diameter. Two (2) per car.
Brake and clutch shank seal
p/n: 60-0019-24
Seal, brake and clutch pedal shank to floorboard. Single bellows rubber cup, seals air drafts around pedals.
Front Bumper Seal
p/n: 70-1103-28
Seals, front bumper. Fully molded rubber, U-shaped. Three and one half inches (3-1/2") long by three and one half inches (3-1/2") wide by thirteen sixteenths inch (13/16") height. For the grommets see our #70-1104-28, sold separately.
Flexible Run Channel - 5ft
p/n: 70-1107-57
Cloth covered mohair-lined type. For sides and top of side windows. Available in 5ft lengths.
Door Weatherstrip
p/n: 40-0367-57
Door belt inner weatherstrip (scraper seal). Front door only. Thirty six (36) inches long.
Fuel Filler Neck Grommet
p/n: 60-0040-41
This Fuel Filler Neck Grommet is a fully molded rubber, grommet slightly angled with a retaining flange. Three and five sixteenths inch (3-5/16") outside width by three and one half inch (3-1/2") outside length by two and one eighth inch (2-1/8") inside hole diameter.
Horn button contact cushion
p/n: 50-0409-21
Separator, horn contact. For standard or non-flexible wheel.
Rumble Seat Lid Corner Pad
p/n: 70-0152-87
Pads, rumble seat lid corners, original rounded triangle shape.Length: 1.5 inches. Width: .4375 inches.
Firewall Grommet
p/n: 70-0223-20
This Firewall Grommet is used on the lower end of the elbow from the firewall to the voltage regulator. Designed from the original part for superior fit and seal.
Rumble Seat Step Mounting Pad
p/n: 50-0182-44
Mounting pad, rumble seat step to fender, proper beaded edge, exact copy.Width: 4.8125 inches.
Side Window Sash Channel
p/n: 70-0641-58
This Side Window Sash Channel is the u-shaped steel channel only, no filler. Sold in 4 foot strip, usually sufficient for two (2) windows.
Cowl vent weatherstrip
p/n: 70-0143-54
Gasket, cowl vent. Perfect copy of original, not a sponge substitute, top quality material.
Trunk Hinge Mounting Pad
p/n: 50-0372-87
Pad, trunk hinge. Non-bead cushion like original. Four (4) piece set.Length: 7.125 inches.
Brake and Clutch Shank Seal
p/n: 40-0175-24
Seal, brake and clutch pedal shank to floorboard. One and one half (1-1/2) inch by two and one eighth (2-1/8) inch by three fourths (3/4) inch thick.
Radio Antenna End Loop
p/n: 70-0105-21
End loop, radio antenna. Cord reinforced rubber with metal grommet. Mounted on running board on some models.
Rear Engine Mount
p/n: 70-0648-11
This Rear Engine Mount is used as an upper and lower support bracket at the transmission. Made from high-quality EPDM rubber for a precise, factory like fit.
Brake and Clutch Pedal Bumper
p/n: 60-0024-24
Bumpers, brake and clutch pedal shank to floorboard. Rides pedal shank under floorboard.
Brake and Clutch Shank Seal
p/n: 30-0055-24
Seals, brake and clutch pedal shanks, against underside of floorboard.Length: 2.5625 inches. Width: 1.75 inches.