Engine Mount Pad
p/n: 30-0267-11
This Engine Mount Pad pair is used as a support insulator at the timing gear cover. Correct design and rubber compound.
Rear Window Gasket
p/n: 20-1676-81
This Rear Window Gasket is designed from the original part for superior fitment and seal. The seal mounts around the full perimeter of the back glass and has vulcanized, or bonded, ends which means no cutting or splicing is required for installation.
Brake and Clutch Pedal Pads - Brown
p/n: 40-0107-89
This reproduction Clutch and Brake Pedal Pad pair slips over the full perimeter of the brake pedal for a precise, factory fit. An oval style perfect reproduction to replace worn original pedal pads. Manufactured in Brown rubber.
Brown Accelerator Pedal Pad
p/n: 70-0208-89
Pad, accelerator pedal. Brown rubber. For black see our #70-0208-40. Made to slip over old metal core after removing old rubber.
Fender Skirt Edge Weatherstrips
p/n: 70-0055-45
This Fender Skirt Edge Weatherstrip pair is designed from the original part for superior fitment, finish and sealing function. Two five (5) foot strips that fit between the rear wheel fender skirt and rear quarter panel.
Heel plate
p/n: 70-3608-88
Heel plate to protect driver's side floor carpet. Identical to original. Only for models with carpet.
Gravel Shield
p/n: 30-0007-44
Gravel deflector, underside of running board at rear. Length: 7.125 inches.
Red Brake and Clutch Pedal Pad
p/n: 30-0188-89
Pads, brake and clutch pedal, slip over type. Black and red rubber. For black only see our #30-0188-22.Length: 3.875 inches. Width: 2.875 inches.
Taillight Mounting Pad
p/n: 30-0198-15
Mounting pad, taillight. With proper edging and shape, molded left and right. Sold only in complete pairs.Length: 9.75 inches.
Front Axle Bumpers
p/n: 20-2175-33
This Front Axle Bumper pair is designed from the original part for an authentic fit, finish and function.
Windshield Gasket
p/n: 20-1605-50
This Windshield Gasket mounts around the full perimeter of the front glass and has the divider bar molded directly into it for a precise, factory fit. It also has the slot to accommodate the outer edge's decorative molding.
Rear Axle Bumpers
p/n: 70-0210-32
This Rear Axle Bumper pair is a quality reproduction of the original factory part. These bottoming pads are dense rubber blocks that mount by bracket to the rear axle tube.
Stabilizer Bushing
p/n: 70-0627-33
Bushings, stabilizer bar, front. Fully molded rubber. One and three fourths inch (1 3/4") length by one and one half inch (1 1/2") width by three fourths inch (3/4") inside hole diameter by one and five eighths inch (1 5/8") height.
Accelerator Pedal Service – Black
p/n: 70-1817-40
Revulcanization Service Only for Black Rubber Accelerator Pedal Pad. For Brown see our 70-1817-89.
Convertible Top Arm Pad
p/n: 70-1217-67
Pad, top folding post. Fastens on lower end of post with two (2) screws. Metal core, close copy.
Hood to Cowl Weatherstrip
p/n: 30-0049-42
Scuff pad, hood to cowl. Superior duplication of part with better rubber than original.Length: 8.25 inches.
Rigid Run Channels
p/n: 30-0023-57
This Rigid Run Channel pair for the division bar is un-beaded, steel core, plush lined, and cloth covered. Available as 28" pair.
Windshield Division Bar Gasket
p/n: 70-0247-51
Gasket set, windshield divider post, inner and outer. Two (2) piece set with screw holes and pilots.