Convertible Top Arm Pad
p/n: 70-1217-67
Pad, top folding post. Fastens on lower end of post with two (2) screws. Metal core, close copy.
Accelerator Pedal Service – Black
p/n: 70-1817-40
Revulcanization Service Only for Black Rubber Accelerator Pedal Pad. For Brown see our 70-1817-89.
Stabilizer Bushing
p/n: 70-0627-33
Bushings, stabilizer bar, front. Fully molded rubber. One and three fourths inch (1 3/4") length by one and one half inch (1 1/2") width by three fourths inch (3/4") inside hole diameter by one and five eighths inch (1 5/8") height.
Rear Axle Bumpers
p/n: 70-0210-32
This Rear Axle Bumper pair is a quality reproduction of the original factory part. These bottoming pads are dense rubber blocks that mount by bracket to the rear axle tube.
Windshield Gasket
p/n: 20-1605-50
This Windshield Gasket mounts around the full perimeter of the front glass and has the divider bar molded directly into it for a precise, factory fit. It also has the slot to accommodate the outer edge's decorative molding.
Front Axle Bumpers
p/n: 20-2175-33
This Front Axle Bumper pair is designed from the original part for an authentic fit, finish and function. These Bumpers are manufactured with top quality materials for good durability.
Taillight Mounting Pad
p/n: 30-0198-15
Mounting pad, taillight. With proper edging and shape, molded left and right. Sold only in complete pairs.Length: 9.75 inches.
Red Brake and Clutch Pedal Pad
p/n: 30-0188-89
Pads, brake and clutch pedal, slip over type. Black and red rubber. For black only see our #30-0188-22.Length: 3.875 inches. Width: 2.875 inches.
Gravel Shield
p/n: 30-0007-44
Gravel deflector, underside of running board at rear. Length: 7.125 inches.
Fender Skirt Edge Weatherstrips
p/n: 70-0055-45
This Fender Skirt Edge Weatherstrip pair is designed from the original part for superior fitment, finish and sealing function. Two five (5) foot strips that fit between the rear wheel fender skirt and rear quarter panel.
Brown Accelerator Pedal Pad
p/n: 70-0208-89
Pad, accelerator pedal. Brown rubber. For black see our #70-0208-40. Made to slip over old metal core after removing old rubber.
Heel plate
p/n: 70-3608-88
Heel plate to protect driver's side floor carpet. Identical to original. Only for models with carpet.
Brake and Clutch Pedal Pads - Brown
p/n: 40-0107-89
This reproduction Clutch and Brake Pedal Pad pair slips over the full perimeter of the brake pedal for a precise, factory fit. An oval style perfect reproduction to replace worn original pedal pads. Manufactured in Brown rubber.
Rear Window Gasket
p/n: 20-1676-81
This Rear Window Gasket is designed from the original part for superior fitment and seal. The seal mounts around the full perimeter of the back glass and has vulcanized, or bonded, ends which means no cutting or splicing is required for installation.
Engine Mount Pad
p/n: 30-0267-11
This Engine Mount Pad pair is used as a support insulator at the timing gear cover. Correct design and rubber compound.
Brown Accelerator Service
p/n: 70-1660-89
Pedal, accelerator. Brown rubber. Revulcanization service only. For black see our #70-1660-40. Color: brown Length: 9.0 inches.
Fender Skirt Edge Weatherstrip
p/n: 70-0790-44
This Fender Skirt Edge Weatherstrip pair is designed from the original part for superior fitment, finish, and seal. This weatherstrips fits between the rear wheel fender skirt and the rear fender quarter panel.
Windshield Division Bar Gasket
p/n: 30-0146-52
Gasket, windshield division bar. Molded inner and outer, fully detailed.Length: 13.625 inches.
Chrome Fender Welting - 50ft
p/n: 70-1102-44
Welting, fender, bright chrome vinyl, three sixteenths (3/16) inch bead, one and one half (1-1/2) inch width. Superior quality. Fifty (50) foot roll. Typically used to attach four (4) fenders to body. For twenty five (25) foot roll see #70-1101-44.
Fender Welting 1/4" Bead - 50ft
p/n: 70-1098-44
Welting, fender. Superior quality, proper construction of reinforced black vinyl over vinyl core, one and three eighths (1-3/8) inch wide. One fourth (1/4) inch bead, fifty (50) foot roll. Typically used to attach four (4) fenders to body.
Fender Welting with 3/16" Bead - 50ft
p/n: 70-1100-44
A superior quality Fender Welting material constructed of reinforced black vinyl over a vinyl core. Typically used for attaching four (4) fenders to body. Sold in a 50 foot roll.
Rear Window Division Bar Seal
p/n: 70-0999-82
Weatherstrip, rear window division bar inner and outer. Die cut to original dimensions.Length: 14.25 inches.
Convertible Top Arm Pad
p/n: 70-1216-67
Pad, top folding post. Fastens on lower end of post with two (2) screws. Metal core, close copy.
Brake and Clutch Pedal Pads - Brown
p/n: 40-0121-89
This reproduction Clutch and Brake Pedal Pad pair slips over the full perimeter of the brake pedal for a precise, factory fit. An oval style perfect reproduction to replace worn original pedal pads. Manufactured in Brown rubber.
Swing-Out Windshield Weatherstrip
p/n: 60-0447-50
This Swing-Out Windshield Weatherstrip is designed from the original part. The seal mounts into the track (channel) attached to the glass that goes all the way around the windshield and creates a seal when the glass is pressed against the body of the vehicle.
Engine Mount Pad
p/n: 30-0238-11
This Engine Mount Pad pair is used as a support cushion at the timing gear cover. Correct design and rubber compound. Sold only in pairs. One (1) pair required per car.
Radiator mounting pad
p/n: 30-0121-31
Grommet, radiator cradle to frame tie rod. 1st type, with locating boss. One four (4) piece set required per car. See also our #30-0309-31.
Division bar grommet
p/n: 70-3135-62
Grommet, rear door vent divider post. Upper and lower, right and left. 4 piece set.
Hinge seal
p/n: 70-0481-73
Filler, front door hinge pillar at dash, right and left. With metal core. Located at top front of front door, under door flange.
Windshield Division Bar Gasket
p/n: 60-0128-52
This two (2) piece Windshield Division Bar Gasket set is designed from the original part for superior fitment and function. Inner and outer windshield division bar molding retainer. With threaded brass core as original (molding not included).
Accelerator Pedal Service – Black
p/n: 70-1813-40
Revulcanization Service Only for Black Rubber Accelerator Pedal Pad. For Brown see our 70-1813-89.
Rear window division bar seal
p/n: 70-0246-82
Gasket set, back window divider post. Inner and outer, with mounting holes. Four (4) piece set.
Front Bumper Grommet
p/n: 30-0071-28
Grommets, front bumper. Proper hollow construction as original for good fit. Fully molded rubber.
Taillight To Body Mounting Pads
p/n: 60-0144-15
This Taillight To Body Mounting Pad pair is designed from the original part for superior fitment and sealing. These reproduction gaskets fit between taillight frame housing and the vehicle body.
Trunk Weatherstrip
p/n: 70-1690-84
This Trunk Weatherstrip is designed from the original part for superior fitment and seal. The weatherstrip mounts around the full perimeter of the trunk directly to the body.
Rear Window Division Bar Weatherstrips
p/n: 70-0632-82
Four (4) piece set, inner and outer, Rear Window Division Bar Weatherstrips. Overall Length: 11-1/2 inches each.
Trunk Weatherstrip
p/n: 70-1129-84
This Trunk Weatherstrip is designed from the original part for superior fitment and seal. The seal mounts around the full perimeter of the trunk lid.
Front Spring Bumpers
p/n: 30-0120-32
This Front Spring Bumper pair is a quality reproduction of the original factory part. Self retaining type bumper manufactured with top quality materials.
Transmission Mount Service
p/n: 60-0407-25
Insulator (support), transmission mounting. Revulcanization service only.Length: 7.0625 inches.
Front Door Vent Window Weatherstrips
p/n: 20-1614-55
These Front Door Vent Window Weatherstrips are the main seals needed to replace the rubber on your vent windows. They are molded as a straight piece and designed from original parts for superior fitment and seal.
Trunk Weatherstrip
p/n: 20-1685-84
This Trunk Weatherstrip is designed from the original part for superior fitment and seal. The seal mounts around the full perimeter of the trunk directly to the body.
Rigid Run Channels
p/n: 70-0536-58
A Rigid Run Channel pair with bright beaded edge, mohair lined channel, die trimmed and round formed at the top. Sold in 29" pairs.
License Light Mounting Pad
p/n: 70-3611-17
Pad, rear license light mounting. Replaces factory #902601.
Carpet Heel Plate
p/n: 40-0190-88
Heel pad. Black rubber. For brown see our #40-0190-89. To protect driver's side floor carpet.