Wheel Cover Cushion
p/n: 70-0633-38
Filler, wheel cover to wheel. Approximately two and one eighth (2-1/8) inches long each, twenty (20) required per car. (Five (5) per wheel cover).
Glovebox Link Bumper
p/n: 70-1459-88
Bumper, glovebox check link. Fits on glovebox door arm as needed.Length: .75 inches. Width: .3125 inches. Height: .4375 inches.
Steering Knuckle Support Seal
p/n: 50-0525-36
Seal, steering knuckle support, upper or lower. Die cut one fourth (1/4) inch, four (4) used per car.Height: .25 inches.
1/16" Sash Channel Filler - Cork
p/n: 70-1115-57
This 1/16" Sash Channel Filler offers the best quality cork product for your classic vehicle project. Manufactured to OEM specifications to install for an authentic fit and finish. Available by the foot.
Tie rod dust cover
p/n: 10-0134-32
Rubber seal, tie rod ends and drag link ends. 2 or 4 required per car. Note: for 4 cylinder vehicles.
Engine Mount Washer
p/n: 20-0442-11
This Front Upper Engine Mount Washer is made of steel. The large upper engine mount insulator sits in this special washer. Fits all Ford 6 cylinder and Flathead V-8 models.
Gravel Shield Bumper
p/n: 33-0286-30
Bumper, rear gravel shield, anti-rattle. Five (5) or more used per car. Fully molded rubber. Replaces factory #1320392.
Run Channel Retaining Clip
p/n: 60-0374-58
This Run Channel Retaining Clip is designed from the original part for an authentic fit, finish and function. Clip fits at the end of door window run channel. Tempered spring steel.
1-3/16" Firewall Grommet
p/n: 32-0112-20
This Firewall Grommet is fully molded and designed from the original part for superior fitment and seal. Designed for firewall applications such as the handbrake cable, heater control cable, and others.
5/8" Radiator Panel Bumper
p/n: 33-0211-31
Lower radiator panel to grille bumper. Also used on radiator valance.
1-3/8" Headlight Grommet
p/n: 32-0437-20
This Headlight Grommet is fully molded and designed from the original part for superior fitment and seal. Designed to run the horn and headlight wires crossover through the radiator shroud.
Windshield Wiper Hose Grommet
p/n: 20-1611-20
This Windshield Wiper Hose Grommet is used to run the wiper hose through the firewall. Designed from original part so it fits correctly.
9/16" Taillight Bumper
p/n: 33-0556-15
Taillight body upper half and fuel filler cover to lower half bumper.
1-1/8" Trunk Floor Pan Plug
p/n: 35-0402-87
This Trunk Floor Pan Plug is designed for floor construction holes and rest pad for the spare wheel area. Six (6) to eight (8) per car, as required.
1-1/4" Utility Plug
p/n: 35-0457-45
This Utility Plug is fully molded and designed from the original part for superior fitment and seal. This plug is made from high-quality EPDM dense rubber to provide excellent durability.
1/16" Sash Channel Filler - Rubber
p/n: 70-2170-57
This 1/16" Sash Channel Filler offers the best quality rubber product for your classic vehicle project. Manufactured to OEM specifications to install for an authentic fit and finish. Available by the foot.
Door Jamb Bumper
p/n: 20-2366-71
This Door Jamb Bumper is a quality reproduction of the original factory part. This rubber bumper mounts into a slot in the door jamb to cushion the door closure. Two (2) required per door.
1/32" Sash Channel Filler - Cork
p/n: 70-1114-57
This 1/32" Sash Channel Filler offers the best quality cork product for your classic vehicle project. Manufactured to OEM specifications to install for an authentic fit and finish. Available by the foot.
1/16" Filler and Cushion Strip
p/n: 70-1236-48
Filler and cushion strip with a variety of applications. Available by the foot.
Shock Absorber Bushing
p/n: 70-0541-33
This Shock Absorber Bushing is manufactured with high-quality Nitrile rubber to OEM specifications. The bushing is the single cone style. Designed from original part and made of high-quality Nitrile dense rubber to ensure durability.
1/32" Sash Channel Filler - Rubber
p/n: 70-2169-57
This 1/32" Sash Channel Filler offers the best quality rubber product for your classic vehicle project. Manufactured to OEM specifications to install for an authentic fit and finish. Available by the foot.
Side Window Bumper
p/n: 70-3428-62
Pad, side window inside anti-rattle. Three eights (3/8) inch by one (1) inch for three sixteenths (3/16) inch by three fourths (3/4) inch slot in sheet metal. Six (6) required per truck
1" Firewall Grommet
p/n: 32-0263-17
This Firewall Grommet is fully molded and designed from the original part for superior fitment and seal. Designed for firewall applications such as license lamp wire through the body, parking brake front cable, and idler lever pull rod.
Side Window Lift Limit Cap
p/n: 60-0071-62
Caps, side window lift limit. Rubber, snap-over type, three fourths (3/4) inch diameter by five sixteenths (5/16) inch thick.
1/4" Universal Mounting Pad
p/n: 70-0308-17
This Universal Mounting Pad is used for lights, hinges, brackets, and other bright work when no molded pad is available. Manufactured with a special edge lip to hug bright work when clamped down. Shape outline to suit application.
Peel-N-Stick Door Weatherstrip
p/n: 70-0331-WT
This Peel-N-Stick Door Weatherstrip is made from high-quality EPDM sponge rubber. Available by the foot.
Peel-N-Stick Door Weatherstrip
p/n: 70-0145-WT
This Peel-N-Stick Door Weatherstrip is made from a high-quality EPDM sponge rubber. Available by the foot.
Shock Absorber Bushing
p/n: 70-0547-32
This Shock Absorber Bushing is manufactured with high-quality EPDM rubber to OEM specifications. The bushing is the double cone style. Designed from original part to ensure proper fit.
11/16" Door Weatherstrip
p/n: 70-0145-73
This Door Weatherstrip is made from high-quality EPDM sponge rubber. Excellent for use on many different vehicle models. Available by the foot.
7/16" Door Weatherstrip
p/n: 30-0243-73
Door edge weatherstrip made from high-quality EPDM sponge rubber. Excellent for use on many different vehicle models. Available by the foot.
1" Firewall Grommet
p/n: 32-0064-21
This Firewall Grommet is fully molded and designed from the original part for superior fitment and seal. This grommet is made from high-quality EPDM dense rubber to provide excellent durability. Designed to run the vacuum line through the firewall.
7/16" Door Weatherstrip
p/n: 70-0331-73
This Door Weatherstrip made from high-quality EPDM sponge rubber. With its generic shape it has many uses outside of its original purpose. Available by the foot.
1" Wiring Grommet
p/n: 32-0047-14
This Wiring Grommet is fully molded and designed from the original part for superior fitment and seal. This grommet is made from high-quality EPDM dense rubber. Designed to run the electric wire through the body for head and taillights.
5/8" Utility Body Plug
p/n: 35-0458-45
This Utility Body Plug is fully molded and designed from the original part for superior fitment and seal. This plug is made from high-quality EPDM dense rubber to provide excellent durability.
5/8" Gearshift Bushing
p/n: 32-0051-24
This Gearshift Bushing is fully molded and designed from the original part for superior fitment and seal. This bushing is made from high-quality EPDM dense rubber to provide excellent durability. Designed for the gearshift selector rod.
Peel-N-Stick Door Edge Weatherstrip
p/n: 70-0390-WT
This Peel-N-Stick Door Edge Weatherstrip is designed for a specific set of vehicles but with its generic shape, has many uses outside of its original purpose. Available by the foot. Available by the foot.
1-1/4" Body Hole Plug
p/n: 20-1039-21
This Body Hole Plug is designed from the original part for superior fitment, finish and function. This plug is made from high quality EPDM dense rubber to provide excellent durability. This body plug covers a sheet metal hole that is one and one fourth (1-1/4") inches in diameter.
3/4" Trunk Floor Pan Plug
p/n: 35-0070-87
This Trunk Floor Pan Plug is fully molded and designed from the original part for superior fitment and seal. This plug is made from high-quality EPDM dense rubber to provide excellent durability.
15/16" Firewall Grommet
p/n: 32-0066-20
This Firewall Grommet is fully molded and designed from the original part for superior fitment and seal. Designed for firewall applications such as running the headlight wire through the fender.
7/16" Door Weatherstrip
p/n: 70-0390-73
This Door Weatherstrip is made from high-quality EPDM sponge rubber. Excellent for use on many different vehicle models. Available by the foot.
Hood and Trunk Bumper Cap for Adjustment Screw
p/n: 70-0294-42
This Hood and Trunk Bumper Cap is designed from the original part for superior fitment, finish and function. Cap type for front hood or rear trunk lid adjustment screw.
Glovebox Door Bumper
p/n: 40-0501-88
This Glovebox Door Bumper is fully molded and designed from the original part for superior fitment and seal. This bumper is made from high-quality EPDM dense rubber to provide excellent durability.
3/4" Gearshift Grommet
p/n: 32-0050-24
This Gearshift Grommet is fully molded and designed from the original part for superior fitment and seal. This grommet is made from high-quality EPDM dense rubber. Designed as an insulator for the gearshift control rod.
3/4" Hood and Door Bumper
p/n: 33-0459-42
This Hood and Door Bumper is fully molded and designed from the original part for superior fitment and seal. Designed for hood to cowl and door hinge pillar upper bumper. May be used in both places.
Window Channel Retaining Clip
p/n: 70-0514-62
Clip, side window run channel retaining. Rust resistant spring steel. Compare with your original.
Trunk or Hood Bumper
p/n: 34-0203-42
This Bumper is designed to be used for the trunk or hood. The bumper is molded with clearance for the screw.
1-3/8" Wiring Grommet
p/n: 32-0369-20
This Wiring Grommet is fully molded and designed from the original part for superior fitment and seal. Designed to run the wiring harness through the fender skirts or hood latch lower mounting panels.
Shock Absorber Link Arm Bushing
p/n: 60-0216-33
This Shock Absorber Link Arm Bushing is designed from the original part for superior fitment, finish and function. This bushing is for double acting shock absorber arm links.
Window Channel Retaining Clip
p/n: 70-0515-62
Clip, side window run channel retaining. Rust resistant spring steel.
1/2" Standard Bumper
p/n: 33-0136-42
This Standard Bumper is fully molded from quality dense rubber to provide excellent durability. Commonly used as a door bumper on the center upper post on post model vehicles.
Choke, Throttle and Starter Wiper Motor Grommet
p/n: 20-1561-20
This Choke, Throttle or Wiper Motor Grommet is designed from the original part for superior fitment and usage. A multi-purpose grommet, it fits into the vehicles firewall to provide a secure passthrough for the mechanical choke, throttle rod or wiper motor wiring.
11/16" Hood Bumper
p/n: 33-0003-42
Bumper, hood, 2 uses. Hood to radiator shell at side panel, hood to fender, as required.
1" Firewall Grommet
p/n: 32-0438-20
This Firewall Grommet is fully molded and designed from the original part for superior fitment and seal. This grommet is made from high-quality EPDM dense rubber to provide excellent durability.
Engine Mount Washer
p/n: 20-0440-11
This Upper Engine Mount Washer is made of steel. Reproduction is designed from the original part to fit correctly.
Chrome Molding Washer
p/n: 60-0727-45
Washer, for attaching chrome moldings on body. Fits into metal cup retainer. Three fourths (3/4) inch diameter, use as required.
Glovebox bumper
p/n: 20-2391-88
Bumpers, glovebox door.Ford Cars 1960 Bumpers, fuel tank door. All Galaxie models. Ford Truck 1935-47 Bumpers, glovebox door.
Door Check Arm Bumper
p/n: 20-1639-70
This Door Check Arm Bumper is designed from the original part for superior fitment and function. This rubber with arm slot bumper mounts on the door check arm. Works to cushion the door swing.
1-1/4" Wiring Grommet
p/n: 32-0401-45
This Wiring Grommet is fully molded and designed from the original part for superior fitment and seal. Designed to run the license light wire through the trunk inner panel.
5/16" Standard Stem Bumper - GM
p/n: 33-0127-41
This 5/16" Standard Stem Bumper is designed from the original part for superior fitment, finish and function. This bumper is commonly used as a console and fuel filler door bumper on GM models.