Body To Frame Mounting Pad Set
p/n: 20-1597-48
This fifteen (15) piece Body to Frame Mounting Pad set is designed from the original parts for superior fitment and function.
Body To Frame Mounting Pad Set
p/n: 20-1596-48
This nineteen (19) piece Body to Frame Mounting Pad set is designed from the original parts for superior fitment and function. These frame pads are installed between the frame and the floor pans.
Body to Frame Webbing
p/n: 20-1599-48
This Body to Frame Webbing is designed from the original part for superior fitment and function. This webbing is used to shim the body to the frame. Also used as a noise reducer material. Webbing is two (2) inch wide, twenty-five (25) foot long roll.
Headlight Mounting Pad
p/n: 30-0354-14
Gasket, headlight front assembly to fender. Between headlight bucket and the fender receiver hole. One (1) pair per car, sold only in pairs.
Rear Window Gasket Set
p/n: 20-0398-81
This Rear Window Gasket Set is designed from the original part for superior fitment and seal. The seal mounts around the full perimeter of the back glass and has vulcanized, or bonded, ends which means no cutting or splicing is required for installation.
Swing-Out Windshield Weatherstrip
p/n: 40-0018-52
This Swing-Out Windshield Weatherstrip comes in an eleven (11) foot strip. The seal slides into the track (channel) attached to the glass that goes all the way around the windshield and creates a seal when the glass is pressed against the body of the vehicle.
Door Bumper
p/n: 70-0168-71
Bumper, door side. Square type held by four (4) screws, metal core as original.
Fender Skirt Edge Weatherstrip
p/n: 20-0111-44
This Fender Skirt Edge Weatherstrip pair is designed from the original part for superior fitment, finish and sealing function. Two five (5) foot strips that fit between the rear wheel fender skirt and rear quarter panel.
Engine Mount Pad
p/n: 70-2577-11
This Engine Mount Pad pair is used as a lower support cushion. Correct design and rubber compound. Sold as a pair.
Radiator Mounting Pad
p/n: 30-0309-31
Grommet, several usages. Radiator core cradle tie rod to frame or rear stabilizer pad to link to where the leaf springs are bolted. Fully molded rubber. 2nd type with chamfered edge. Comes as a (4) piece set.
Suspension bushing
p/n: 30-0339-36
Bushing, insulator, front suspension lower support arm, inner. Four (4) piece set.
Suspension bushing
p/n: 30-0335-36
Bushing, insulator, torque arm to frame at rear. Four (4) piece set.
Taillight Mounting Pad
p/n: 40-0177-15
Pads, taillight bracket mounting, right and left. Length: 9.375 inches.
Division Bar Grommet
p/n: 70-0483-62
These Division Bar Grommets are fully molded for the rear door vent divider post (wind deflector). Four (4) piece set.
Front Suspension Rubber Bumper
p/n: 60-0103-32
Front Suspension Rubber Bumper for the front suspension lower control arm (attaches to lower arm spring mount). Steel core, with original size bolt. Width: 1.625 inches.
Fuel Neck Grommet
p/n: 10-0136-41
Grommet, fuel filler neck. Oblong, fully molded rubber. Three and one fourth inch (3-1/4") outside length by two and three sixteenth inch (2-3/16") inside diameter.
Clutch or Brake Pedal Pad - Brown
p/n: 70-0176-89
This reproduction Clutch or Brake Pedal Pad slips over the full perimeter of the pedal for a precise, factory fit. A perfect reproduction to replace worn original pedal pads. Manufactured in quality brown rubber.
Hood Corner Pad
p/n: 40-0127-42
Pads, hood corners, brass core. Approximately 80 degree angle. Integral tabs for installing.Length: 1.50 inches.
Front Stabilizer Bushing
p/n: 70-0193-33
Bushings, front stabilizer bar. Fully molded rubber. One and five eighths inch (1 5/8") length by one and seven sixteenths inch (1 7/16') width by three fourths inch (3/4") inside hole diameter by one and eleven sixteenths inch (1 11/16") height.
Fresh air gasket
p/n: 70-1768-31
Seal, fresh air adaptor door. Part of assembly #903964. For vehicles with accessory air control systems.
Brake and Clutch Pedal Pads - Black
p/n: 40-0121-22
This reproduction Clutch and Brake Pedal Pad pair slips over the full perimeter of the brake pedal for a precise, factory fit. An oval style perfect reproduction to replace worn original pedal pads. Manufactured in Black rubber. For Brown see our 40-0121-89.
Clutch and Brake Pedal Pads - BROWN
p/n: 25-0024-89
This reproduction Clutch and Brake Pedal Pad pair slips over the full perimeter of the brake pedal for a precise, factory fit. A reproduction with authentic type ribbing, to replace worn original pedal pads. Manufactured in Brown rubber.
Fuel Neck Grommet
p/n: 18-0020-41
Grommet, fuel filler neck. Fully molded rubber with retaining flange.
Stabilizer Bar End Link Set
p/n: 70-0567-34
Twenty-two (22) piece Stabilizer Bar End Link set for both sides of one (1) vehicle, fits front or rear bar. Order two (2) sets for vehicles with front and rear stabilizer bars. Hex head bolt. 5/16"-24NF x 7-5/8" long. Includes metal sleeves, cup washers and rubber grommets.
Taillight Mounting Pad
p/n: 27-0069-15
Pad, taillight mounting pad to body. Fully molded with original details. Length: 6.375 inches.
Front Stabilizer Bushing
p/n: 50-0170-34
Bushings, front stabilizer bar mounting. Fits original bracket. Fully molded rubber. One and five eighths inch (1 5/8") length by one and three eighths inch (1 3/8") outside diameter by eleven sixteenths inch (11/16") inside hole diameter.
Rear Gravel Deflector to Bumper Face Bar
p/n: 70-0462-45
This Rear Gravel Deflector to Bumper Face Bar staples to the gravel deflector. The seal is die cut from dense rubber. Sold as a six (6) foot strip.
Rear Stabilizer Bushing
p/n: 50-0171-34
Bushings, rear stabilizer bar mounting. Fully molded rubber. One and one half inch (1 1/2") length by one and one fourth inch (1 1/4" outside diameter by nine sixteenths inch (9/16") inside hole diameter.
Front Stabilizer Bushing
p/n: 30-0363-33
Bearings or bushings, front stabilizer rod. One (1) pair used per vehicle. Fully molded rubber.
Taillight Mounting Pad
p/n: 60-0008-15
Mounting pads, taillight. Length: 6.50 inches. Width: 2.6875 inches.
Clutch and Brake Pedal Pads
p/n: 60-0068-22
This reproduction Clutch and Brake Pedal Pad pair slips over the full perimeter of the pedal for a precise, factory fit. An oval style perfect reproduction to replace worn or damaged original pedal pads.
Door weatherstrip
p/n: 20-1644-73
Weatherstrips, open car door hinge. Door seals molded to fit hinge area.
Front Spring Rubber Bumpers
p/n: 70-0329-32
This Front Spring Rubber Bumper Pair fits to the upper control arms on frame. Manufactured to OEM specifications to install for an authentic fit, finish and function.
Accelerator Pedal Pad
p/n: 70-0208-40
Pad, accelerator pedal. Black rubber. For brown see our #70-0208-89. Made to slip over old metal core after removing old rubber. Length: 8.25 inches.
Clutch and Brake Pedal Pads - BLACK
p/n: 25-0024-22
This reproduction Clutch and Brake Pedal Pad pair slips over the full perimeter of the brake pedal for a precise, factory fit. A reproduction with authentic type ribbing, to replace worn original pedal pads. Manufactured in Black rubber.
Door Bumper
p/n: 34-0305-71
Bumper assembly, front door hinge, upper, stop. Two (2) per car, steel core as original.Height: .6875 inches.
Suspension bushing
p/n: 30-0341-36
Bushing, insulator, upper support arm, outer above steering knuckle support. Four (4) piece set.
Brake Master Cylinder Filler Access Hole Cover
p/n: 60-0016-24
This Master Cylinder Access Hole Cover is designed from the original part for superior fitment and seal. Secures the Brake Master Cylinder Filler and Inspection Access Hole in the vehicle.
1935-1974 Cadillac Factory Parts Manual, CD
p/n: 07-1346-07
This GM Licensed Detroit Iron CD provides the most comprehensive set of digital Cadillac Factory parts manuals. The factory manuals on this CD were professionally scanned from the original service and parts manuals.
Clutch Equalizer Bushing and Seals
p/n: 70-2029-24
This Clutch Equalizer Bushing and Seal set is designed from the original part for superior fitment and operation. The set includes a metal sleeved rubber bushing and two (2) molded rubber seals for each end of equalizer shaft.
Front Suspension Bumper
p/n: 60-0093-32
Bumper, front lower suspension arm. Attaches to front cross member by carrot retainer.Height: 2.0 inches.
Overload Spring Arm Bumpers
p/n: 70-2301-32
A reproduction Overload Spring Arm Bumper pair manufactured to OEM specifications. Fully molded quality rubber bumpers that installs in the truck's overload spring arms.
Door - Gravel Shield - Running Board Weatherstrip
p/n: 60-0054-73
This Door - Gravel Shield - Running Board Weatherstrip is a anti-squeak bulb type extrusion with fitment for General Motors vehicles. A twelve (12) foot strip made of high-quality EPDM dense rubber and designed from original parts for superior fitment, finish and function.
Flexible Run Channel - 60 Inch
p/n: 20-1619-58
Channel, side window glass, vertical run. Flexible, felt lined, rubber covered channel. Available 60" lengths.
Flexible Run Channel
p/n: 20-1146-58
This Flexible Run Channel helps to eliminate window rattle, provides a smooth sliding surface for glass movement, and works to protect the glass. Stainless steel beaded. Available in sixty (60) inch strips.
Front Stabilizer Bushing
p/n: 30-0123-33
Bushings, front stabilizer mounting bracket. Fully molded rubber.
Rear Gravel Deflector to Bumper Seal
p/n: 60-0020-30
This Rear Gravel Deflector to Bumper Seal is made of a high quality EPDM dense rubber extrusion. Designed from the original part so it fits correctly. Sold as a six (6) foot strip.
Window Pinchweld Seal
p/n: 70-0096-52
This twelve (12) foot Window Pinchweld Seal is designed from the original part for superior fitment and function. The part is used to seal and retain an outer decorative reveal molding. Used with our 70-1192-52.
Rear coil spring pad
p/n: 50-0359-35
Insulators, rear coil spring. Fabric reinforced rubber as original. One (1) pair per car.
Door Hinge Weatherstrips
p/n: 20-1643-73
This Door Hinge Weatherstrip pair is designed from the original parts for superior fitment and sealing. These door edge weatherstrips are molded specifically to fit the door hinge area of the vehicle.
Cowl Vent Gasket
p/n: 30-0050-54
Gasket, cowl vent. Perfect reproduction, high quality, original configuration, not a sponge substitute.Length: 14.0 inches. Width: 5.75 inches.
Cowl Vent Gasket
p/n: 40-0271-54
Gasket, cowl vent. Fully molded to original cross-section and outline.Length: 18.0 inches.
Fuel Neck Grommet
p/n: 40-0043-39
Grommet, fuel filler neck. Fully molded rubber with retaining flange. Three and five eighths inch (3-5/8") outside diameter by two and one eighth inch (2-1/8") inside diameter by one inch (1") height.
Rear Window Gasket
p/n: 20-1668-81
This Rear Window Gasket mounts around the full perimeter of the back glass and has vulcanized, or bonded, ends. It also has the slot to accommodate the outer edge's decorative molding.
Rear Window Gasket
p/n: 20-0395-81
This Rear Window Gasket is designed from the original part for superior fitment and seal. The seal mounts around the full perimeter of the back glass and has vulcanized, or bonded, ends which means no cutting or splicing is required for installation.
Rear Window Gasket
p/n: 20-1660-81
This Rear Window Gasket mounts around the full perimeter of the back glass and has vulcanized, or bonded, ends which means no cutting or splicing is required for installation.
Exterior Windshield Division Bar
p/n: 20-2341-51
This stainless steel Exterior Windshield Division Bar is designed from the original part for superior fitment, appearance and function.
Accelerator Pedal Service
p/n: 60-0701-40
Pedal, accelerator. Revulcanization service only. Excellent cover detailing with molded in rod ball socket as original.
Cowl Vent Gasket
p/n: 70-0194-54
Gasket, cowl vent. Original solid rubber configuration, not a sponge substitute.
Firewall Grommet
p/n: 30-0070-21
This Firewall Grommet is used to run instrument board cables through the firewall. The oval type with masked hole for six (6) wires or cables is the necessary replacement for correct restoration.
Front Bow Weatherstrip
p/n: 60-0440-64
Weatherstrip, front bow to windshield, outer. Installs on convertible top. Approximately four (4) foot ten (10) inches long.
Gearshift Boot - Black
p/n: 20-0334-26
This reproduction Black Gearshift Boot is designed from the original part for an authentic fit, finish, and appearance.
Hood Corner Pad
p/n: 60-0118-42
Pad. hood corner, steel core as original, front and rear.Length: 1.5 inches.
Brown seat back rest pad
p/n: 70-0482-89
Rest pads, seat back, outer, on two (2) door styles with folding seats. Brown rubber. For black see our #70-0482-88. Self retaining, perfect copy.
Front and Rear Bumper Spacer
p/n: 70-0184-30
Spacer or mute, front and rear bumper mounting bar to gravel deflector. Fully molded rubber. Two and nine sixteenths inch (2-9/16") outside length by seven eighths inch (7/8") width by thirteen sixteenths inch (13/16") height.
Front Door weatherstrip
p/n: 10-0115-73
Weatherstrip, door opening, special bulb seal with lip to fit original retainer. Approximately 46 inch strip.Width: .375 inches. Height: .625 inches.
Parking Light Mounting Pad
p/n: 60-0007-17
Mounting pads, parking lights.Length: 4.25 inches. Width: 2.375 inches.
Steering Column Grommet - Brown
p/n: 60-0621-89
This brown rubber Steering Column To Toe Board Grommet is designed from the original part for superior fitment and sealing. Part is molded from quality rubber to authentic original dimensions.
Headlight Door To Lens Weatherstrips
p/n: 70-0493-14
This Headlight Door To Lens Weatherstrip pair is the double lip type for sealed beam headlights. The pair is molded without wire. Designed from the original part to fit correctly.
Rigid Run Channels
p/n: 70-0347-58
This Rigid Run Channel pair is stainless beaded and mohair-lined to help eliminate window rattles and provide a smooth sliding surface for glass movement. Also works to protect the glass.
Rear Valance Gasket Strip
p/n: 70-0461-45
This Rear Valance Gasket Strip installs on the gravel shield to body. Designed from the original part so it fits correctly. Customer will need to cut bolt clearance as needed.
Taillight Lens Gasket
p/n: 70-1213-15
Gasket, taillight lens. For the main pad order our #70-1212-15.Length: 6.875 inches.
Cowl Vent Gasket
p/n: 30-0262-54
Gasket, cowl vent. Labyrinth style as original.Length: 12.75 inches.
Steering Column Grommet - Black
p/n: 60-0621-36
This black rubber Steering Column To Toe Board Grommet is designed from the original part for superior fitment and sealing. Part is molded from quality rubber to authentic original dimensions.
Flexible Run Channel - 6 Ft.
p/n: 70-1108-57
Channel, flexible window run, un-beaded. Cloth covered mohair-lined type. Available in 6ft lengths.
Clutch and Brake Pedal Pads - Bowtie Emblem
p/n: 60-0125-22
This reproduction Clutch and Brake Pedal Pad pair slips over the full perimeter of the pedal for a precise, factory fit. A perfect reproduction to replace worn original pedal pads. Manufactured in quality black rubber with Chevy bowtie in tread.
Engine Snubber Pad Set
p/n: 30-0311-11
This four (4) piece Engine Snubber Pad Set is designed from original for correct fit and function. Sold only in complete sets. One four (4) piece set required per car.
Beltline Weatherstrips
p/n: 40-0539-57
This Beltline Weatherstrip pair installs on the left and right doors to wipe the inside and outside of the windows when the glass is lowered. Flexible, pile lined, rubber covered, with a black bead. Available in 3ft pair.
Brake and Clutch Shank Seal
p/n: 40-0217-24
Draft cap for brake and clutch pedal.Length: 2.4375 inches. Width: 1.6875 inches.
Vent division bar weatherstrip
p/n: 30-0347-74
Weatherstrip, rear vent window, front edge (on division post) right and left.
Vent division bar weatherstrip
p/n: 30-0346-56
Front vent window division post seal. Fully molded with metal core and attaching tabs.
Clutch Control Boot
p/n: 30-0273-24
Boot, clutch control unit governor.1940-42: Cars with Overdrive 1941-42: Cars with Electromatic
Flexible Run Channel
p/n: 70-1239-58
This Flexible Run Channel provides a smooth sliding surface while helping to eliminate rattle and protect the glass. The run channel has the stainless beaded edge and is cloth covered and mohair lined with the flexible metal channel.
Fuel Neck Grommet
p/n: 60-0401-41
Grommet, fuel filler neck. Fully molded, slightly angled. Four and one fourth inch (4-1/4") inch outside diameter by two and one eighth inch (2-1/8") inside hole diameter by seven eights inch (7/8") height at front.
Hood Bumper
p/n: 70-0409-42
Bumpers, hood top panel at cowl. One half (1/2) inch by one half (1/2) inch by three and one fourth (3-1/4) inch. Held in place by screws. Two (2) to four (4) per car as required.
Parking Light Lens Gasket
p/n: 50-0164-16
Pad, fender parking light lens.Width: 5.125 inches. Height: 2.25 inches.