Fender Welting with 3/16" Bead - 50ft
p/n: 70-1100-44
A superior quality Fender Welting material constructed of reinforced black vinyl over a vinyl core. Typically used for attaching four (4) fenders to body. Sold in a 50 foot roll.
Accelerator Pedal Service - Brown
p/n: 27-0082-89
Revulcanization Service Only for Brown Rubber Accelerator Pedal Pad. For Black see our #27-0082-40.
Engine Mount Pad
p/n: 30-0267-11
This Engine Mount Pad pair is used as a support insulator at the timing gear cover. Correct design and rubber compound.
Rear Window Gasket
p/n: 20-0396-81
This Rear Window Gasket is designed from the original part for superior fitment and seal. The seal mounts around the full perimeter of the back glass and has vulcanized, or bonded, ends which means no cutting or splicing is required for installation.
Taillight Mounting Pad
p/n: 40-0392-15
Pad, brake light. Mounts on center of trunk lid.Length: 13.125 inches.
Engine Mount Service – Revulcanization Only
p/n: 10-0135-11
This Revulcanization Service Only is designed to restore your Engine Support Mount to a like new original condition. Service requires your metal core. Please call or email for more service details and ordering.
License Plate Light Lens Gaskets
p/n: 70-0560-17
This License Plate Light Lens Gasket pair is designed from the original part for superior fitment and seal. This reproduction gasket fits between the License Plate Light Lens and the License Plate Light Housing or Bezel.
Brown Accelerator Pedal Pad
p/n: 70-0208-89
Pad, accelerator pedal. Brown rubber. For black see our #70-0208-40. Made to slip over old metal core after removing old rubber.
Red Brake and Clutch Pedal Pad
p/n: 30-0188-89
Pads, brake and clutch pedal, slip over type. Black and red rubber. For black only see our #30-0188-22.Length: 3.875 inches. Width: 2.875 inches.
Windshield Gasket
p/n: 20-1605-50
This Windshield Gasket mounts around the full perimeter of the front glass and has the divider bar molded directly into it for a precise, factory fit. It also has the slot to accommodate the outer edge's decorative molding.
Rear Bumper Grommet
p/n: 40-0468-30
Grommets, rear bumper. Fully molded rubber, used on rear side brackets only.
Convertible Top Arm Pad
p/n: 50-0310-67
Pad, folding post, lower, on bottom of post, held by two (2) screws. Brass core, right and left hand.
Rear Axle Bumpers
p/n: 70-0210-32
This Rear Axle Bumper pair is a quality reproduction of the original factory part. These bottoming pads are dense rubber blocks that mount by bracket to the rear axle tube.
Stabilizer Bushing
p/n: 70-0627-33
Bushings, stabilizer bar, front. Fully molded rubber. One and three fourths inch (1 3/4") length by one and one half inch (1 1/2") width by three fourths inch (3/4") inside hole diameter by one and five eighths inch (1 5/8") height.
Convertible Top Arm Pad
p/n: 70-1217-67
Pad, top folding post. Fastens on lower end of post with two (2) screws. Metal core, close copy.
Roof Rail Filler
p/n: 50-0255-67
Filler, folding top side roof rail to front roof rail. Right and left with metal core as original.
Rigid Run Channels
p/n: 30-0023-57
This Rigid Run Channel pair for the division bar is un-beaded, steel core, plush lined, and cloth covered. Available as 28" pair.
Transmission Mount Revulcanization Service Only
p/n: 10-0157-25
This Revulcanization Service is designed to restore your existing Transmission Mount to a like new original condition. Service requires your metal core. Please call or email for more service details and ordering.
Front Spring Bumpers
p/n: 60-0393-32
This Front Spring Bumper pair is a quality reproduction of the original factory part. These axle to frame bottoming rebound pads are dense rubber blocks that mount to the front axle.
Fender Skirt Edge Weatherstrip
p/n: 70-0154-45
This Fender Skirt Edge Weatherstrip pair is designed from the original part for superior fitment, finish, and seal. This weatherstrips fits between the rear wheel fender skirt and the rear fender quarter panel.
Side Window Beltline Scraper Weatherstrips
p/n: 60-0566-58
These inner and outer Side Window Beltline Scraper Weatherstrips slide into the groove on top of the door's window opening and wipes the glass when window is raised and lowered. Four (4) piece set.
Spring Shackle Bushing Set
p/n: 20-1581-33
This Spring Shackle Bushing Set is for the rear leaf springs. This set is an original steel stud type.