Hood bumper
p/n: 70-0543-42
Bumpers, hood to fender. Mounted on hood, rubber with steel core. Replaces Bakelite originals which are not available.
Headlight Mounting Pad
p/n: 10-0122-14
Pad, headlight housing to the mounting bracket that secures the housing to the fender.
Body to door conduit
p/n: 70-0506-21
Conduit (double rubber hose), body to door, for hydraulic and electrical lines to power window.
Door weatherstrip
p/n: 20-1649-73
Weatherstrip, back of door, vertical section. Material enough for all four doors, cut to fit at installation.
License Light Mounting Pad
p/n: 30-0122-17
Pad, rear license light mounting, with correct dimensions and beading.Length: 8.125 inches.
Chrome Fender Welting - 25ft
p/n: 70-1101-44
Welting, fender, bright chrome vinyl, three sixteenths (3/16) inch bead, one and one half (1-1/2) inch width. Superior quality. Twenty five (25) foot roll. Typically used to attach two (2) fenders to body. For fifty (50) foot roll see our #70-1102-44.
Fender Welting 1/4" Bead - 25ft
p/n: 70-1097-44
Welting, fender. Superior quality, proper construction of reinforced vinyl over vinyl core, one and three eighths (1-3/8) inch wide, black only. One fourth (1/4) inch bead, twenty-five (25) foot roll. Typically used to attach two (2) fenders to body.
Vent division bar weatherstrip
p/n: 50-0464-74
Weatherstrip, division post. Rear door on models with rear door vent. Made with metal core and attaching tabs like original.
Sliding Quarter Window Weatherstrip
p/n: 70-0353-78
This Sliding Quarter Window Weatherstrip is used for side window inner and/or outer, front and/or rear doors. Available in a 6ft. lengths.
Convertible Top Front Bow Weatherstrip
p/n: 70-0100-64
This Convertible Top Front Bow Weatherstrip is designed from the original part for superior fitment and seal. This header seal installs directly to the windshield frame to seal between the soft top and the top of the windshield.
Trunk Hinge Mounting Pad
p/n: 70-1229-87
Mounting pad, trunk hinge. Four (4) piece set.Length: 7.625 inches.
Window Felt Beltline Weatherstrips - 3ft Pair
p/n: 30-0244-57
This side window Window Felt Beltline Weatherstrip pair can be used as inner and/or outer. The weatherstrip is flexible, pile lined, rubber covered, with black bead. Available in 3ft pairs.
Suspension Bumper - Front Lower Control Arm
p/n: 50-0092-32
This Suspension Bumper is designed from the original part for superior fitment and function. Bumper mounts to the front suspension lower control arm. Two (2) per car required.
Floor Board Seals
p/n: 20-1595-88
This Floor Board Seal set contains all of the correct sealing components for the front floor boards.
Fender Welting with 3/16 Bead - 25ft
p/n: 70-1099-44
A superior quality Fender Welting material constructed of reinforced black vinyl over a vinyl core. Typically used for attaching two (2) fenders to body. Sold in a 25 foot roll.
Headlight Mounting Pad
p/n: 30-0142-14
Gaskets, headlight body mounting to fender. Cut to exact size as original.
Door Weatherstrip
p/n: 60-0114-73
Weatherstrip, door bottom, sponge constant section, solid skin surface, superior quality. Sold in six (6) foot strips only.Length: 72.0 inches.
Front Stabilizer Bushing
p/n: 60-0088-34
This Front Stabilizer Bushing pair is fully molded from EPDM dense rubber to ensure durability. Used to connect the stabilizer bar to the vehicle frame. Two (2) required per car.
Flexible Run Channel - 5ft
p/n: 70-1107-57
Cloth covered mohair-lined type. For sides and top of side windows. Available in 5ft lengths.
License Light Mounting Pad
p/n: 40-0391-85
Pad, trunk handle and license light housing.Length: 5.875 inches.
Horn button contact cushion
p/n: 50-0409-21
Separator, horn contact. For standard or non-flexible wheel.
Headlight Mounting Pad
p/n: 70-0201-14
This Headlight Mounting Pad is designed from the original part for superior fitment and seal. This pad acts as the headlight adjusting collar. Sold as a pair.
Fuel Filler Neck Grommet
p/n: 60-0040-41
This Fuel Filler Neck Grommet is a fully molded rubber, grommet slightly angled with a retaining flange. Three and five sixteenths inch (3-5/16") outside width by three and one half inch (3-1/2") outside length by two and one eighth inch (2-1/8") inside hole diameter.
Horn Button Contact Set
p/n: 60-0492-21
This is a three (3) piece Horn Button Contact set which is designed from the original part for superior fitment and function. Renews the operation of the steering wheel horn blowing ring.
Cowl Vent Hose
p/n: 60-0457-54
Hose, cowl vent drain. Seems to be correct for some models rather than our #50-0259-54.
License Light Mounting Pad
p/n: 60-0074-17
Mounting pad, license light. Three and one eighth (3-1/8) inch by eight and seven eighths (8-7/8) inch. Fully detailed.Length: 8.875 inches.
Door Lower Weatherstrips
p/n: 20-1652-73
This three (3) piece Lower Door Weatherstrip set is designed from the original part for superior fitment and seal. Use full-length for front doors, cut third piece in half to complete installation for both rear doors.
License Lens Gasket
p/n: 70-2276-16
Gasket, license light lens. Fully molded with proper details.Length: 3.0 inches. Width: 1.6875 inches.
Brake and clutch shank seal
p/n: 70-0465-23
Grommets, brake and clutch pedal shank below floorboard.
Side Window Sash Channel
p/n: 70-0641-58
This Side Window Sash Channel is the u-shaped steel channel only, no filler. Sold in 4 foot strip, usually sufficient for two (2) windows.
Parking light gasket
p/n: 70-2651-16
Gaskets, front parking light. Lamp base. For lens gasket see our #70-2652-16. This style used on Series 75 models only with small parking lamp.
Firewall Grommet
p/n: 70-0554-20
This Firewall Grommet is a special rectangular, two (2) hole grommet, that is used on the left side of the cowl the run the hydraulic line through the sheet metal.
Backup Light Mounting Pad
p/n: 60-0072-17
Mounting pads, back up lights, elliptic, sharp beaded edge. One and five sixteenths (1-5/16) inch by two and seven eighths (2-7/8) inch.Length: 2.
Cowl vent weatherstrip
p/n: 70-0143-54
Gasket, cowl vent. Perfect copy of original, not a sponge substitute, top quality material.
Brake and Clutch Shank Seal
p/n: 40-0175-24
Seal, brake and clutch pedal shank to floorboard. One and one half (1-1/2) inch by two and one eighth (2-1/8) inch by three fourths (3/4) inch thick.
Trunk stop lamp lens gasket
p/n: 70-3525-15
Gasket, trunk stop lamp lens. Used on the decklid center of the trunk. Fully molded rubber.
Fuel Tank Filler Neck Grommet
p/n: 20-0345-39
This Fuel Tank Filler Neck Grommet is designed from the original part for superior fitment and seal. This grommet fits around the vehicles fuel filler neck between the filler neck and vehicle body.
Cowl Vent Gasket
p/n: 60-0124-54
Gasket, cowl vent. Original labyrinth style, not sponge.Length: 16.5 inches. Width: 4.0 inches.
Fabric Hood Lacing
p/n: 20-0354-42
This Fabric Hood Lacing installs where the hood rests on the cowl panel. Original woven style lacing complete with installation tacks. Sold as a forty-nine (49) inch strip.
Convertible Top Rest Bump Stop Block
p/n: 70-0397-67
This Convertible Top Rest Bump Stop Block pair is designed from the original part for an authentic fit, finish, and appearance. Attaches to the folding pillar arm of the convertible top assembly. This rubber only bumper block glues to the original metal core.
Rigid Run Channels
p/n: 70-0516-58
This Rigid Run Channel pair is zinc plated steel with black cloth inside lining to provide a smooth sliding surface for glass movement. Also works to protect the glass. Fastens in place by small screws or rivets on top and bottom.
License Light Mounting Pad
p/n: 25-0045-17
Pad, rear license light body.Length: 7.0 inches. Width: 3.375 inches.
Taillight Gasket
p/n: 70-0900-15
Gasket, taillight housing. Also order #70-0471-15 for the taillight mounting pad, and for the taillight lens gasket order #70-0658-15. Length: 8.25 inches.
Antenna Mount Pad
p/n: 70-2621-21
Pad, roof mounted antenna gasket. Models with antenna mounted above center of windshield.
Hood to Cowl Weatherstrip
p/n: 60-0056-42
This Hood to Cowl Weatherstrip is extruded from a high quality dense rubber for a durable and proper seal. This seal mounts at the rear of the engine bay to seal between the hood and vehicle body cowl.
Hood to Cowl Weatherstrip
p/n: 60-0090-42
This Hood to Cowl Weatherstrip is extruded from a high quality dense rubber for a durable and proper seal. This pair comes with pre-drilled holes for easy installation.
Door Lock Weatherstrip
p/n: 50-0172-70
Weatherstrip, door lock, front and rear. Protects door lock mechanism from dust and weather.Length: 3.625 inches.
Fuel Neck Grommet
p/n: 10-0123-41
Grommet, fuel filler neck. Fully molded soft flexible rubber. Two and seven sixteenths inch (2-7/16") outside diameter by one and seven sixteenths inch (1-7/16") inside hole diameter by five sixteenths (5/16") height.
2-3/8" Firewall Grommet
p/n: 70-0185-20
This Firewall Grommet is used to run the main wiring harness in addition to five (5) accessory wires through the firewall. Designed from the original part for superior fit and seal.
Trunk Weatherstrip
p/n: 60-0562-85
This Trunk Weatherstrip is designed from the original part for superior fitment and seal. The seal mounts on the lower length of the trunk directly to the body.
Flexible Run Channel - 30 Inch Pair
p/n: 40-0309-57
Channel, side window glass, vertical run. Flexible, felt lined, rubber covered channel. Available in 30" pair.
Taillight Retainer Pad
p/n: 60-0340-17
This Taillight Retainer Pad is designed from the original part for superior fitment and seal. These reproduction mounting pads fit to the rear taillight assembly.
Fender Welting
p/n: 20-1590-44
This black Fender Welting is designed from the original part for superior fitment and seal. This welting material fits between the fenders and the vehicle body. Thirty (30) foot roll.
Gearshift Seal
p/n: 60-0471-24
This Gearshift Seal is designed from the original part for superior fitment and function. For the gearshift at floor.
Track Bar Bushing
p/n: 25-0080-32
Bushing, rear axle track bar. Made in halves for easier replacement. Sold in pairs, two (2) pair needed per bar.Height: .75 inches.
Center Division Bar Chrome Molding Retainer
p/n: 70-0373-51
Center Division Bar Chrome Molding Retainer for outside windshield center post stainless molding. Use with original stainless molding and clips. Length: 15-1/2 inches. Width: 1-1/4 inches.
Engine Mount
p/n: 20-1978-11
This Engine Mount is designed from the original part for superior fitment and function. This engine mount works to absorb and isolate engine and driveline vibrations. The set services one mount. 1937-1941 require four (4) sets for both Front and Rear. 1942-1948 require two (2) sets.
Running Board Mounting Pad
p/n: 20-1603-49
Grommets, running board to frame and front fender to cowl. Rubber grommets and metal washers. Twenty four (24) piece set.
Top Motor Grommet Set
p/n: 20-1637-67
This Top Motor Grommet Set contains three (3) pieces that are used for the top motor to the firewall bracket. Designed from the original part for superior fit and seal.
Rear Bumper Stone Deflector
p/n: 20-1569-29
This Rear Bumper Stone Deflector installs between the metal gravel deflector and the inside of the rear bumper. Made from top quality rubber to ensure durability and proper seal.
Gearshift Gasket
p/n: 60-0397-24
This sponge rubber Gearshift Gasket is one-half (1/2) inch thick. For the gearshift at floorboard. One required per vehicle.
License Light Mounting Pad
p/n: 50-0034-17
Pad, rear license light and trunk handle body.Length: 7.50 inches.
Gravel Shield Bumper Set
p/n: 60-0146-30
This Gravel Shield Bumper Set is used as a rear bumper deflector. Also used between the radiator grille and the lower panel. Two (2) required per car. Designed from the original part for superior fitment and seal.
Exhaust System Hanger
p/n: 70-0626-13
Insulator (hanger) tailpipe to frame. See also our #70-0600-13.Length: 3.9375 inches. Width: 1.9375 inches.
5" Wide Bow Drill Cloth Tape
p/n: 70-1175-65
This Bow Drill Cloth Tape is used for covering convertible side window weatherstrip. Black in color and available in a five (5) foot roll.