Clutch and Brake Pedal Pads - Black
p/n: 40-0107-22
This reproduction Clutch and Brake Pedal Pad pair slips over the full perimeter of the brake pedal for a precise, factory fit. An oval style perfect reproduction to replace worn original pedal pads. Manufactured in Black rubber.
3" Firewall Grommet
p/n: 30-0110-42
This Firewall Grommet pair is used for the hood lock link through the firewall. Designed from the original part for superior fit and seal.
Taillight Lens Gasket
p/n: 40-0348-15
Gasket taillight lens. Relieved top and bottom as original, for better sealing.Length: 4.3125 inches. Width: 2.5 inches.
Body To Frame Mounting Pad Set
p/n: 20-1598-48
This twenty-five (25) piece Body To Frame Mounting Pad set is designed from the original parts for superior fitment and function. A complete set of rubber pads and biscuits to isolate the vehicle body from the vehicle frame. Installation instructions are included.
Body to Frame Webbing
p/n: 20-1599-48
This Body to Frame Webbing is designed from the original part for superior fitment and function. This webbing is used to shim the body to the frame. Also used as a noise reducer material. Webbing is two (2) inch wide, twenty-five (25) foot long roll.
Trunk Emblem Mounting Pad
p/n: 50-0114-17
Mounting pad, trunk ornament. Top quality material, finely detailed.Hole to hole this part measures 9.5 inches.Width: 13.875 inches.
Rear Window Gasket Set
p/n: 20-0398-81
This Rear Window Gasket Set is designed from the original part for superior fitment and seal. The seal mounts around the full perimeter of the back glass and has vulcanized, or bonded, ends which means no cutting or splicing is required for installation.
Swing-Out Windshield Weatherstrip
p/n: 40-0018-52
This Swing-Out Windshield Weatherstrip comes in an eleven (11) foot strip. The seal slides into the track (channel) attached to the glass that goes all the way around the windshield and creates a seal when the glass is pressed against the body of the vehicle.
Door Bumper
p/n: 70-0168-71
Bumper, door side. Square type held by four (4) screws, metal core as original.
Hood To Cowl Weatherstrip
p/n: 60-0091-42
This Hood To Cowl Weatherstrip pair is molded with all original details. One (1) pair required per car. Length: 11 inches.
Fender Skirt Edge Weatherstrip
p/n: 20-0111-44
This Fender Skirt Edge Weatherstrip pair is designed from the original part for superior fitment, finish and sealing function. Two five (5) foot strips that fit between the rear wheel fender skirt and rear quarter panel.
Engine Mount Pad
p/n: 70-2577-11
This Engine Mount Pad pair is used as a lower support cushion. Correct design and rubber compound. Sold as a pair.
Radiator Mounting Pad
p/n: 30-0309-31
Grommet, several usages. Radiator core cradle tie rod to frame or rear stabilizer pad to link to where the leaf springs are bolted. Fully molded rubber. 2nd type with chamfered edge. Comes as a (4) piece set.
Division Bar Grommet
p/n: 70-0483-62
These Division Bar Grommets are fully molded for the rear door vent divider post (wind deflector). Four (4) piece set.
Front Suspension Rubber Bumper
p/n: 60-0103-32
Front Suspension Rubber Bumper for the front suspension lower control arm (attaches to lower arm spring mount). Steel core, with original size bolt. Width: 1.625 inches.
Clutch or Brake Pedal Pad - Brown
p/n: 70-0176-89
This reproduction Clutch or Brake Pedal Pad slips over the full perimeter of the pedal for a precise, factory fit. A perfect reproduction to replace worn original pedal pads. Manufactured in quality brown rubber.
Front Stabilizer Bushing
p/n: 70-0193-33
Bushings, front stabilizer bar. Fully molded rubber. One and five eighths inch (1 5/8") length by one and seven sixteenths inch (1 7/16') width by three fourths inch (3/4") inside hole diameter by one and eleven sixteenths inch (1 11/16") height.
Fresh air gasket
p/n: 70-1768-31
Seal, fresh air adaptor door. Part of assembly #903964. For vehicles with accessory air control systems.
Spring Shackle Bushing Set
p/n: 20-1580-33
This Spring Shackle Bushing Set is for the front leaf springs. This set is an original steel stud type.
Brake and Clutch Pedal Pads - Black
p/n: 40-0121-22
This reproduction Clutch and Brake Pedal Pad pair slips over the full perimeter of the brake pedal for a precise, factory fit. An oval style perfect reproduction to replace worn original pedal pads. Manufactured in Black rubber. For Brown see our 40-0121-89.
Taillight Mounting Pad
p/n: 27-0069-15
Pad, taillight mounting pad to body. Fully molded with original details. Length: 6.375 inches.
Stabilizer Bar End Link Set
p/n: 70-0567-34
Twenty-two (22) piece Stabilizer Bar End Link set for both sides of one (1) vehicle, fits front or rear bar. Order two (2) sets for vehicles with front and rear stabilizer bars. Hex head bolt. 5/16"-24NF x 7-5/8" long. Includes metal sleeves, cup washers and rubber grommets.