Door weatherstrip
p/n: 20-1649-73
Weatherstrip, back of door, vertical section. Material enough for all four doors, cut to fit at installation.
Flexible Run Channel
p/n: 70-1238-58
Cloth covered, mohair lined flexible metal channel for sides and top of door windows.
Clutch and Brake Pedal Pads - Brown
p/n: 50-0054-89
This reproduction Clutch and Brake Pedal Pad pair slips over the full perimeter of the pedal for a precise, factory fit. A perfect reproduction to replace worn original pedal pads. Manufactured in quality brown rubber.
Rear spring bushing
p/n: 60-0311-35
Bushing, rear spring front eye, inlox cartridge type as original.
Cab Bumper
p/n: 60-0510-48
Bumper, cab hold down bolts. Comes as a pair of two (2). Fully molded rubber.
Brake and clutch shank seal
p/n: 70-0192-23
Grommets, clutch and brake pedal shank. Hollow accordion action type, not a sponge ring.
Front Stabilizer Bushing
p/n: 50-0094-34
Bushings, front stabilizer shaft-to-frame or stabilizer shaft, front or rear. Fully molded rubber.
Brake and Clutch Shank Seal
p/n: 30-0143-24
Boot, brake and clutch pedal shank at toe board.Length: 2.9375 inches.
Gearshift Boot
p/n: 70-2126-24
Boot, transmission gear hand shift lever. Molded in pliable black rubber which may be painted if needed for restoration.
Headlight Door To Lens Ring Seals
p/n: 70-0389-14
This Headlight Door To Lens Ring seal pair is designed from the original part for superior fitment and function. The part works to seal between the headlight door housing and the headlight retaining ring. The part is a single lip type seal for sealed beam headlights.
Windshield Division Bar Gasket
p/n: 70-0372-51
This Windshield Division Bar Gasket is designed from the original part for superior fitment and seal. Part is properly sized with "H" section. Part requires fitting to top and bottom, as it is not drilled.
Folding seat bumper
p/n: 70-0482-88
Rest pads, seat back, outer, on two (2) door styles with folding seats. Black rubber. For brown see our #70-0482-89. Self retaining, perfect copy.
Front Bumper Gravel Shield Mute
p/n: 30-0399-29
These Front Bumper Gravel Shield Mutes are fully molded out of quality EPDM rubber. They are sold as a pair to fit on the outer bumper brackets. Designed to slide over the outer bumper to put tension on the bottom of the shield to prevent rattle.
Running Board or Inner Fender Splash Filler
p/n: 60-0288-45
This eight (8) foot Splash Filler strip is used for the running board apron to body or fender splash panels anti-rattle filler. This filler strip is top-quality EPDM sponge rubber to accept rivets or retaining screws.
Vent Division Bar Weatherstrip
p/n: 70-0695-74
Division bar seal. Proper cross section rubber molded to original style metal with authentic attaching tabs.
License Light Mounting Pad
p/n: 27-0035-17
Pad, license light and trunk handle mounting.Length: 6.875 inches.
Vent division bar weatherstrip
p/n: 70-0694-56
Front vent window division post seal. Fully molded with metal core and attaching tabs.
Clutch or Brake Pedal Pad - Black
p/n: 70-0176-22
This reproduction Clutch or Brake Pedal Pad slips over the full perimeter of the pedal for a precise, factory fit. A perfect reproduction to replace worn original pedal pads. Manufactured in quality black rubber.
Fuel Neck Grommet
p/n: 40-0352-39
Grommet, fuel filler neck, exact copy with thirty (30) degree slope. Fully molded rubber with retaining flange. Three and five sixteenths inch (3-5/16") outside width by four and one eight inch (4-1/8") outside length.
Vent Window Division Post Weatherstrips
p/n: 60-0569-56
This Front Window Vent Division Post Weatherstrip pair is fully molded with metal core and attaching tabs.
Vent Window Division Post Weatherstrips
p/n: 60-0494-56
This front door Vent Window Division Post Weatherstrip pair is designed from the original part for superior fitment and seal. Fully molded rubber with metal core and attaching tabs.
Window Felt Beltline Weatherstrips
p/n: 70-0555-58
These Window Felt Beltline Weatherstrips are sold as a three (3) foot pair. The beltline is used for side windows inner and/or outer, front and/or rear doors. Available in a 3ft pair.
Vent division bar weatherstrip
p/n: 70-0791-56
Front vent window division post seal. Fully molded with metal core and attaching tabs.
Vent Division Bar Weatherstrip
p/n: 70-2089-56
This Front Vent Division Bar Weatherstrip is fully molded with metal core and attaching tabs.
Vent division bar weatherstrip
p/n: 30-0530-56
Front vent window division post seal. Fully molded with metal core and attaching tabs.
Parking Light Lens Gasket
p/n: 50-0164-16
Pad, fender parking light lens.Width: 5.125 inches. Height: 2.25 inches.
Hood Bumper
p/n: 70-0409-42
Bumpers, hood top panel at cowl. One half (1/2) inch by one half (1/2) inch by three and one fourth (3-1/4) inch. Held in place by screws. Two (2) to four (4) per car as required.
Flexible Run Channel
p/n: 70-1239-58
This Flexible Run Channel provides a smooth sliding surface while helping to eliminate rattle and protect the glass. The run channel has the stainless beaded edge and is cloth covered and mohair lined with the flexible metal channel.
Clutch Control Boot
p/n: 30-0273-24
Boot, clutch control unit governor.1940-42: Cars with Overdrive 1941-42: Cars with Electromatic
Fuel Neck Grommet
p/n: 60-0401-41
Grommet, fuel filler neck. Fully molded, slightly angled. Four and one fourth inch (4-1/4") inch outside diameter by two and one eighth inch (2-1/8") inside hole diameter by seven eights inch (7/8") height at front.
Vent division bar weatherstrip
p/n: 30-0346-56
Front vent window division post seal. Fully molded with metal core and attaching tabs.
Vent division bar weatherstrip
p/n: 30-0347-74
Weatherstrip, rear vent window, front edge (on division post) right and left.
Brake and Clutch Shank Seal
p/n: 40-0217-24
Draft cap for brake and clutch pedal.Length: 2.4375 inches. Width: 1.6875 inches.
Beltline Weatherstrips
p/n: 40-0539-57
This Beltline Weatherstrip pair installs on the left and right doors to wipe the inside and outside of the windows when the glass is lowered. Flexible, pile lined, rubber covered, with a black bead. Available in 3ft pair.
Clutch and Brake Pedal Pads - Bowtie Emblem
p/n: 60-0125-22
This reproduction Clutch and Brake Pedal Pad pair slips over the full perimeter of the pedal for a precise, factory fit. A perfect reproduction to replace worn original pedal pads. Manufactured in quality black rubber with Chevy bowtie in tread.
Engine Snubber Pad Set
p/n: 30-0311-11
This four (4) piece Engine Snubber Pad Set is designed from original for correct fit and function. Sold only in complete sets. One four (4) piece set required per car.
Flexible Run Channel - 6 Ft.
p/n: 70-1108-57
Channel, flexible window run, un-beaded. Cloth covered mohair-lined type. Available in 6ft lengths.
Cowl Vent Gasket
p/n: 30-0262-54
Gasket, cowl vent. Labyrinth style as original.Length: 12.75 inches.
Steering Column Grommet - Black
p/n: 60-0621-36
This black rubber Steering Column To Toe Board Grommet is designed from the original part for superior fitment and sealing. Part is molded from quality rubber to authentic original dimensions.
Taillight Lens Gasket
p/n: 70-1213-15
Gasket, taillight lens. For the main pad order our #70-1212-15.Length: 6.875 inches.
Rear Valance Gasket Strip
p/n: 70-0461-45
This Rear Valance Gasket Strip installs on the gravel shield to body. Designed from the original part so it fits correctly. Customer will need to cut bolt clearance as needed.
Headlight Door To Lens Weatherstrips
p/n: 70-0493-14
This Headlight Door To Lens Weatherstrip pair is the double lip type for sealed beam headlights. The pair is molded without wire. Designed from the original part to fit correctly.
Rigid Run Channels
p/n: 70-0347-58
This Rigid Run Channel pair is stainless beaded and mohair-lined to help eliminate window rattles and provide a smooth sliding surface for glass movement. Also works to protect the glass.
Steering Column Grommet - Brown
p/n: 60-0621-89
This brown rubber Steering Column To Toe Board Grommet is designed from the original part for superior fitment and sealing. Part is molded from quality rubber to authentic original dimensions.