Starter Pedal Pad
p/n: 40-0094-21
Pad, starter pedal, snap over cover with tread pattern matching other pedals.Length: 2.25 inches.
Trunk Bumper
p/n: 40-0082-85
Bumper, trunk lid, rubber. Retained by two (2) screws (not included).Width: 2.50 inches. Height: 1.625 inches.
Engine Mount Pad
p/n: 11-0026-11
This Engine Mount Pad is designed to original pattern with superior workmanship. Made from high-quality EPDM rubber for a precise, factory like fit. Two (2) required per car.
Side Mount Clamp Cushion
p/n: 40-0138-37
Cushion, sidemount clamp. Two and one eighth (2-1/8) inch by four and five eighths (4-5/8) inch.Length: 4.625 inches. Width: 2.125 inches.
Rumble Seat Step Pad
p/n: 60-0126-45
Pad, rumble seat step, on rear bumper bracket or fender. Rubber cover only, full slip-over type with bowtie emblem.
Taillight Gasket
p/n: 70-0258-15
Gaskets, taillight mounting under fender wire conduit base. Width: 3.25 inches.
Headlight Stanchion Pad
p/n: 70-0255-21
Mounting pads, horn and headlight stanchion base to hood latch shelf. Two and one half (2-1/2) inches by four and one fourth (4-1/4) inches.Length: 4.
Rumble Seat Step Mounting Pad
p/n: 70-0262-45
Pad, rumble seat step plate mounting, rectangle type for top of fender.Length: 4.875 inches. Width: 4.25 inches.
Gearshift Boot
p/n: 40-0076-88
Dust boot, gearshift, beehive type. Excellent copy and material. Used on some shift ball sockets.Length: 4.75 inches.
Coil wire sleeve
p/n: 70-0109-21
Sleeve, coil wire to distributor. Fluted to match upper water hoses rubber only. V-12 & V-16 with coils mounted in radiator, V-8 with coils mounted horizontally on brace rods.
Hood Bumper
p/n: 40-0354-42
Bumper, fender to hood. Two (2) per car. Held by four (4) rivets.Length: 2.9375 inches.
Fuel Neck Grommet
p/n: 40-0067-39
Grommet, fuel filler neck. Oblong, fully molded rubber. Four and one eighth inch (4-1/8") outside length by two and one fourth inch (2-1/4") inside diameter.
Firewall Pass Through Grommet
p/n: 40-0522-21
This Firewall Pass Through Grommet is the rectangular large type. Designed from the original part for superior fit and seal.
Parking Light Mounting Pad
p/n: 30-0282-17
Gaskets, parking light (fender light).Length: 2.75 inches. Width: 1.75 inches.
Steering Column Grommet
p/n: 40-0007-36
Grommet, steering column at floor. One and one half (1-1/2) inch tube.
Side Mount Cover Pad
p/n: 40-0314-37
Anti-rattle, spare wheel cover in fenderwell.Width: .25 inches.
Transmission Mounting Pad
p/n: 11-0025-25
Mount, transmission. Original pattern, superior workmanship.
Accelerator Pedal Pad
p/n: 10-0001-40
Pad, accelerator pedal. Cements and fastens with screws to original metal pedal. Length: 6.50 inches.
Brake Master Cylinder Filler Access Hole Cover
p/n: 60-0016-24
This Master Cylinder Access Hole Cover is designed from the original part for superior fitment and seal. Secures the Brake Master Cylinder Filler and Inspection Access Hole in the vehicle.
Rumble Seat Step Pad
p/n: 40-0050-44
Pad, rumble seat step, with "P" logo, fully detailed slipover pad for old core. Fits original trim ring.Height: .50 inches.
Front Spring Bumper
p/n: 50-0423-35
Bumper, front spring. Fits onto original bracket.Length: 2..125 inches. Width: 2.0 inches. Height: 1.875 inches.
Rear Window Gasket
p/n: 70-0084-77
This Rear Window Gasket comes in a seven foot, six inch (7' 6") strip and mounts around the full perimeter of the back glass. The ends may require trimming and bonding for installation.
Hood Corner Pad
p/n: 40-0128-42
Pads, hood corners. Square type, brass core. Integral installation tabs. 90 degree angle, used on front or rear corners, as required.
Fuel Neck Grommet
p/n: 30-0232-41
Grommet, fuel filler neck. 2-1/2" inside diameter. Fits 3-3/8" hole in sheet metal. Overall width 4-1/8".
Quarter Window Weatherstrip
p/n: 60-0446-77
Weatherstrip, stationary quarter windows. Eight (8) foot strip for two (2) quarter windows. Most models with stationary windows.Length: 96.0 inches.
Accelerator Pedal Pad - Black
p/n: 50-0080-40
Accelerator pedal pad manufactured in Black rubber. Full slip-over type and a perfect copy. For Brown see our #50-0080-89.
Rear Window Gasket
p/n: 70-0018-83
This Rear Window Gasket comes in a seven foot, three inch (7' 3") strip and mounts around the full perimeter of the back glass. The ends may require trimming and bonding for installation.
Access Hole Plug
p/n: 10-0010-44
Cover, rear apron over fuel tank. 3-1/2 inch diameter hollow cup to cover hole above fuel gauge sending unit.
Rumble Seat Weatherstrip
p/n: 14-0051-87
Weatherstrip or rubber buffer, rumble seat opening notch-out on perimeter of opening near water catch rail. Two (2) used per car.
Brake and Clutch Pedal Pads
p/n: 40-0213-22
Pad, brake and clutch pedals. Horizontal oval style, slip over type.Length: 3.8125 inches. Width: 2.375 inches.
Steering Column Floorplate
p/n: 17-0001-36
Grommet, steering column floor, black rubber only, excellent copy of original.Length: 5.0 inches.
Headlight Grommet
p/n: 40-0009-14
Grommet, headlight bar to shell. One and one fourth (1-1/4) inch round hole.
Windshield Gasket
p/n: 70-0078-52
This Windshield Gasket is made of a high-quality EPDM dense rubber extrusion. This four (4) foot weatherstrip mounts on the lower windshield.
Accelerator Pedal Pad - Brown
p/n: 50-0080-89
Accelerator pedal pad manufactured in Brown rubber. Full slip-over type and a perfect copy.
Brake and Clutch Pedal Pads
p/n: 30-0188-22
Pads, brake and clutch pedal, slip over type. Black rubber only. For black and red (semi-automatic clutch models) see our #30-0188-89.Length: 3.875 inches.
Carpet Heel Plate
p/n: 40-0087-88
Heel pad for carpet. Identical to original. Five and three fourths (5-3/4) inch by ten and one half (10-1/2) inch, to be stitched in place.Length: 10.
Cowl Vent Gasket
p/n: 70-0713-54
Gasket, cowl side ventilator. One eighth (1/8) inch sponge rubber.Length: 11.375 inches. Width: 4.625 inches.
Rear Spring Bumper
p/n: 60-0137-32
Bumper, rear spring. Fits original retainer.Width: 2.5625 inches.
Steering Column Grommet
p/n: 15-0002-36
Grommet, steering column clamp at dash, one and three fourths (1-3/4)inch wide for one and three fourths (1-3/4)inch column.Length: 6.125 inches.
Rumble Seat Step Pad
p/n: 40-0209-44
Pad, rumble seat step slip over style for original core, "DB" logo.
Brake and Clutch Pedal Pads
p/n: 40-0038-22
Pad, brake and clutch pedal. See also our #40-0072-22.Length: 3.8125 inches. Width: 2.3125 inches.
Rumble Seat Step Pad
p/n: 40-0353-44
Pad, rumble seat step, with "DS" logo. Fits old bracket and bezel. See our #40-0055-44 also.Height: .50 inches.
Steering Column Grommet
p/n: 70-1512-36
Insulator, steering column bracket. Two (2) pieces of extruded rubber like original.Width: 1.3125 inches.
Red Brake and Clutch Pedal Pad
p/n: 30-0188-89
Pads, brake and clutch pedal, slip over type. Black and red rubber. For black only see our #30-0188-22.Length: 3.875 inches. Width: 2.875 inches.
Radiator Brace Filler Strip
p/n: 70-0020-31
Filler strip, radiator brace rods. Retains ignition wire and thermometer tube in hollow brace rods. Thirty (30) inch strips.
Sidemount Wheel Carrier Grommet
p/n: 60-0002-37
This Sidemount Wheel Carrier Grommet for the wheel carrier brace support-at-cowl panel. Manufactured with a heavy brass core. Has a flexible neck. A close copy of original.
Fender Welting with 3/16" Bead - 50ft
p/n: 70-1100-44
A superior quality Fender Welting material constructed of reinforced black vinyl over a vinyl core. Typically used for attaching four (4) fenders to body. Sold in a 50 foot roll.
Chrome Fender Welting - 50ft
p/n: 70-1102-44
Welting, fender, bright chrome vinyl, three sixteenths (3/16) inch bead, one and one half (1-1/2) inch width. Superior quality. Fifty (50) foot roll. Typically used to attach four (4) fenders to body. For twenty five (25) foot roll see #70-1101-44.
Fender Welting 1/4" Bead - 50ft
p/n: 70-1098-44
Welting, fender. Superior quality, proper construction of reinforced black vinyl over vinyl core, one and three eighths (1-3/8) inch wide. One fourth (1/4) inch bead, fifty (50) foot roll. Typically used to attach four (4) fenders to body.
Windshield stanchion base pad
p/n: 40-0244-52
Mounting pad. Windshield post in open cars. 6 cylinder
Brake and Clutch Pedal Pads
p/n: 40-0072-22
Pad, brake and clutch pedal.Length: 3.9375 inches. Width: 2.9375 inches.
Rumble Seat Step Pad
p/n: 40-0012-44
Pad, rumble seat step bears Chrysler medallion logo in center.Height: .50 inches.
Starter pedal pad
p/n: 40-0158-21
Pad, starter pedal. Rectangular outline, curved as original to fit oval steel pedal core, proper tread pattern to match other pedals.
Front Spring Bumper
p/n: 50-0238-35
Bumpers, front spring, Two (2) per car.Width: 2.0 inches. Height: 1.75 inches.
Shock absorber arm seal
p/n: 40-0081-32
Dust seal set, shock absorber link, rubber only. Eight (8) piece set.
Headlight Grommet
p/n: 40-0008-14
Grommets, headlight bar to shell. Slightly oval. One and one fourth (1-1/4) inch diameter hole.
LaSalle Monogram
p/n: 70-0056-49
LaSalle monograms for center of running board matting, exact copy, to be in-laid.
Rumble Seat Step Pad
p/n: 40-0124-44
Pad, rumble seat step, with "Dodge" logo, slip over type to fit old steel core. Perfect detail and lettering.Height: .50 inches.
Cadillac V-8 Pedal Pad
p/n: 70-0148-22
Cadillac V-8 pedal pads, clutch and brake. Another rare one we finally found to copy. Superior copy.
Luggage Rack Grommet
p/n: 17-0021-46
Grommet, luggage rack support arm through body.Length: 2.25 inches. Width: 1.25 inches.
Firewall Grommet Set
p/n: 70-1147-21
This Firewall Grommet Set contains six (6) pieces intended for spark and choke rods, fuel line, oil gauge line and radiator brace rods. Designed from the original part for superior fit and seal.
Side Mount Spare Grommet Set
p/n: 70-1136-37
This six (6) piece Side Mount Spare Grommet Set is made from top-quality EPDM rubber and designed from the original parts for durability and proper function. This set can be used for various applications to support arms, brace rods, and cowl standoff posts.
Engine Mount Pad
p/n: 70-1161-11
This Engine Mount Pad pair is designed from the original for an exact original configuration. For cars with round cone-type front mounts.