Starter Pedal Pad
p/n: 40-0094-21
Pad, starter pedal, snap over cover with tread pattern matching other pedals.Length: 2.25 inches.
Trunk Bumper
p/n: 40-0082-85
Bumper, trunk lid, rubber. Retained by two (2) screws (not included).Width: 2.50 inches. Height: 1.625 inches.
Headlight tube flange gasket
p/n: 50-0223-14
Headlight tube flange gasket. Two (2) per car. Replaces #1234556.
Running Board or Inner Fender Splash Filler
p/n: 60-0288-45
This eight (8) foot Splash Filler strip is used for the running board apron to body or fender splash panels anti-rattle filler. This filler strip is top-quality EPDM sponge rubber to accept rivets or retaining screws.
Golf Bag Door Weatherstrip
p/n: 70-0118-85
This Golf Bag Door Weatherstrip is designed from the original part for superior fitment and seal. This seal mounts directly to the golf bag door.
Firewall Grommet
p/n: 25-0026-20
This Firewall Grommet is the six (6) hole type used to run wires, cables, or tubes through the firewall. Designed from the original part for superior fit and seal.
Rear spring bushing
p/n: 60-0311-35
Bushing, rear spring front eye, inlox cartridge type as original.
Fuel Line Grommet
p/n: 30-0045-41
Grommet, fuel gauge and gas line through rear frame cross member. For five eighths (5/8) inch by two and three eighths (2-3/8) inch slot.Length: 2.
Body Mounting Pad
p/n: 70-0299-48
Pad, body mounting, for body bracket. Two (2) collars and retaining rings. Four (4) per car.
Chrome Fender Welting - 25ft
p/n: 70-1101-44
Welting, fender, bright chrome vinyl, three sixteenths (3/16) inch bead, one and one half (1-1/2) inch width. Superior quality. Twenty five (25) foot roll. Typically used to attach two (2) fenders to body. For fifty (50) foot roll see our #70-1102-44.
Fender Welting 1/4" Bead - 25ft
p/n: 70-1097-44
Welting, fender. Superior quality, proper construction of reinforced vinyl over vinyl core, one and three eighths (1-3/8) inch wide, black only. One fourth (1/4) inch bead, twenty-five (25) foot roll. Typically used to attach two (2) fenders to body.
Body Mounting Pad
p/n: 60-0412-48
Body bumpers, rear, at body hold-down bolt. Fully molded rubber. Comes as a pair of two (2). One and three fourths inch (1 3/4") outside length by one and one fourth inch (1 1/4") diameter by three eighths inch (3/8") inside hole diameter.
Clutch and Brake Pedal Pads - Bowtie Emblem
p/n: 60-0043-22
This reproduction Clutch and Brake Pedal Pad pair slips over the full perimeter of the pedal for a precise, factory fit. A perfect reproduction to replace worn original pedal pads. Manufactured in quality black rubber. Excellent detail with bowtie emblem like original.
Cowl Vent Gasket
p/n: 30-0259-54
Gasket, cowl vent. Sponge rubber, good copy of original. Thirty seven and one half (37-1/2) inch developed length.Length: 37.50 inches.
Electrical terminal boot
p/n: 30-0061-21
Cover, starter cable terminal post inside to frame. Full detail and molded as original part.
Fender Welting with 3/16 Bead - 25ft
p/n: 70-1099-44
A superior quality Fender Welting material constructed of reinforced black vinyl over a vinyl core. Typically used for attaching two (2) fenders to body. Sold in a 25 foot roll.
Rumble Seat Lid Bumper Pad
p/n: 60-0191-87
Bumper pad, rumble seat lid, upper corners. Compare with our #70-0120-87.Width: 1.0 inches. Height: 1.125 inches.
Brake and clutch shank seal
p/n: 60-0019-24
Seal, brake and clutch pedal shank to floorboard. Single bellows rubber cup, seals air drafts around pedals.
Brake and clutch pedal bumper
p/n: 30-0380-20
Bumper, inclined toe board pedal hole, carried on toe board to meet our #30-0055-24 pedal. dust cover.
Side Window Sash Channel
p/n: 70-0641-58
This Side Window Sash Channel is the u-shaped steel channel only, no filler. Sold in 4 foot strip, usually sufficient for two (2) windows.
1-1/4" Firewall Grommet
p/n: 30-0060-21
This Firewall Grommet is used to run the coil wire and temperature gauge line through the firewall. Designed from the original part for superior fit and seal.
Brake and Clutch Shank Seal
p/n: 40-0175-24
Seal, brake and clutch pedal shank to floorboard. One and one half (1-1/2) inch by two and one eighth (2-1/8) inch by three fourths (3/4) inch thick.
Horn trumpet grommet
p/n: 40-0086-21
Grommet for trumpet horn wire through motor cover. Close reproduction. Two (2) per car.
Brake and Clutch Shank Seal
p/n: 30-0055-24
Seals, brake and clutch pedal shanks, against underside of floorboard.Length: 2.5625 inches. Width: 1.75 inches.
Fender Well Pad
p/n: 15-0011-37
Pad, fender well for sidemounted spares. One (1) pair per fender.Length: 2.875 inches. Width: 2.875 inches. Height: .4375 inches.
Headlight Bracket Pad
p/n: 50-0222-14
Headlight bracket-to-fender pad. POA #1245890-1, right and left.
Flexible Run Channel - 30 Inch Pair
p/n: 40-0309-57
Channel, side window glass, vertical run. Flexible, felt lined, rubber covered channel. Available in 30" pair.
Body Mounting Pad
p/n: 70-0297-48
Pad, body mounting. Three eighths (3/8) inch by two (2) inch by three (3) inch with collar and retainer ring.
Rumble Seat Lid Corner Pad
p/n: 70-0120-87
Pad, rumble seat lid corner, Compare with our #60-0191-87. Length: .75 inches.
5" Wide Bow Drill Cloth Tape
p/n: 70-1175-65
This Bow Drill Cloth Tape is used for covering convertible side window weatherstrip. Black in color and available in a five (5) foot roll.
Firewall Pass Through Grommet
p/n: 40-0523-21
This Firewall Pass Through Grommet is the smaller rectangular type. Made from high-quality dense rubber to provide excellent durability.
Brake and Clutch Shank Seal
p/n: 40-0016-24
Seal, brake and clutch pedal shank to floorboard (draft excluder).Length: 2.4375 inches. Width: 1.875 inches.
Firewall Grommet
p/n: 50-0272-20
This Firewall Grommet is used to run the water temperature indicator pipe through the dash. Designed from the original part for superior fit and seal.
Starter Button Cover
p/n: 60-0322-21
This Starter Button Cover is designed from the original part for an authentic fit, finish, and appearance. A push on replacement to rod. Two (2") inch outside diameter.
Hood latch swivel
p/n: 70-0061-42
Swivel, hood latch. Exact copy from .075 steel, pierced for rivets, not plated.
Accelerator Rod Button Cover
p/n: 60-0357-40
Cover, accelerator rod button. Round slip-over type. Good copy with bow tie center. Height: .4375 inches.
Shock Absorber Arm Bushing
p/n: 30-0192-32
Bushing, shock absorber arm. Restore proper shock action.Height: 1.375 inches.
Steering Column Spacer
p/n: 60-0563-32
Spacer, steering column to dash at U-clamp.Length: 2.50 inches.
Door Bumper
p/n: 17-0041-70
Pad, door jamb, large size, retained by both dovetail retainer from back, and screw through center. Usually 2 per door.Length: 2.125 inches. Width: 1.
Rear Spring Pad
p/n: 70-0191-32
Pad, rear spring insulator for two (2) inch wide springs. (see our number 70-0245-32 for two and one fourth (2-1/4) inch springs). Cloth reinforced. Four (4) per vehicle.
Rumble Seat Lid Bumper Pad
p/n: 40-0297-85
Bumper, rumble seat lid. Sometimes used on trunk. One half (1/2) inch by one (1) inch by one (1) inch. Two (2) per car.Length: 1.0 inches. Width: 1.0 inches.
Door Alignment Pad
p/n: 70-1821-71
Wedge pads, door aligning.Length: 1.125 inches. Width: .5 inches. Height: .875 inches.