Front and Rear Door Bumper
p/n: 34-0025-42
High quality steel core Front and Rear Door Bumper for front and rear body hinge pillar. Mounted by screw. For auxiliary use only where needed to prevent door rattles. Replaces factory #372341.
Front Apron Crossbar Grommet
p/n: 70-1130-45
Grommets, front splash apron crossbar.Width: 3.5 inches. Height: 3.6875 inches.
Front Apron Crossbar Grommet
p/n: 17-0002-45
This two (2) piece Front Apron Crossbar Grommet pair is for the left and right side. Made of a top quality EPDM Dense rubber to ensure durability.
Front Apron Crossbar Grommets
p/n: 70-1131-45
This Front Apron Crossbar Grommet pair is designed from the original part for superior fitment, finish and function. Width: 3-1/2" inches. Height: 3-1/2" inches.
Front Bow Weatherstrip
p/n: 30-0066-67
Pad, folding top, front frame to windshield. Five sixteenths (5/16) inch by one half (1/2) inch rectangular section, fifty (50) inches long. Length: 50.
Front Bow Weatherstrip
p/n: 70-0137-64
Weatherstrip, front bow-to-windshield, soft rubber, hollow body, proper screw holes, hinged flaps front and back.
Front Engine Cushion Set
p/n: 25-0037-11
This four (4) piece Front Engine Cushion Set is molded from a high-quality EPDM dense rubber. Designed from an original part for an exact reproduction.
Front Engine Mount Support Cushion
p/n: 70-0324-11
This Front Engine Mount Support Cushion is designed from an original part to correct specification for a correct fit and appearance.
Front Spring Bumper
p/n: 50-0238-35
Bumpers, front spring, Two (2) per car.Width: 2.0 inches. Height: 1.75 inches.
Front Spring Bumper
p/n: 50-0423-35
Bumper, front spring. Fits onto original bracket.Length: 2..125 inches. Width: 2.0 inches. Height: 1.875 inches.
Front spring mounting block
p/n: 11-0015-33
Shock insulator or mounting block, front spring, both ends. Four (4) piece set.
Fuel Line Grommet
p/n: 30-0045-41
Grommet, fuel gauge and gas line through rear frame cross member. For five eighths (5/8) inch by two and three eighths (2-3/8) inch slot.Length: 2.
Fuel Neck Grommet
p/n: 30-0232-41
Grommet, fuel filler neck. 2-1/2" inside diameter. Fits 3-3/8" hole in sheet metal. Overall width 4-1/8".
Fuel Neck Grommet
p/n: 40-0067-39
Grommet, fuel filler neck. Oblong, fully molded rubber. Four and one eighth inch (4-1/8") outside length by two and one fourth inch (2-1/4") inside diameter.
Gearshift Boot
p/n: 40-0076-88
Dust boot, gearshift, beehive type. Excellent copy and material. Used on some shift ball sockets.Length: 4.75 inches.
Gearshift Floorplate
p/n: 40-0137-88
Floorplate, gearshift and handbrake cover. Steel core as original, with exact rubber pattern.Length: 13.125 inches. Width: 10.875 inches.
Gearshift Floorplate
p/n: 40-0017-88
Floorplate, gearshift and handbrake. Full metal insert as original.Length: 13.125 inches.
Gearshift Floorplate
p/n: 40-0156-88
Floorplate, gearshift and handbrake. Hole cover, grass core as original.Length: 12.50 inches. Width: 9.0 inches.
Gearshift Floorplate
p/n: 40-0058-88
Floorplate, gearshift and handbrake. Fine detail, metal core as original.Length: 8.125 inches.
Gearshift Floorplate
p/n: 17-0005-24
Floorplate, gearshift and handbrake, black rubber only.Length: 10.625 inches. Width: 8.875 inches.
Golf Bag Door Weatherstrip
p/n: 70-0118-85
This Golf Bag Door Weatherstrip is designed from the original part for superior fitment and seal. This seal mounts directly to the golf bag door.
Handbrake Floorplate
p/n: 11-0005-24
Floor plate, handbrake lever. Brass core as original, fully detailed.
Headlight Bar Grommet
p/n: 11-0002-14
Grommet, headlight bar-to-radiator shell. Includes clearance groove, faithful detail. 1-1/8 inch inside diameter.
Headlight Bracket Pad
p/n: 50-0222-14
Headlight bracket-to-fender pad. POA #1245890-1, right and left.
Headlight Grommet
p/n: 40-0008-14
Grommets, headlight bar to shell. Slightly oval. One and one fourth (1-1/4) inch diameter hole.
Headlight Grommet
p/n: 40-0009-14
Grommet, headlight bar to shell. One and one fourth (1-1/4) inch round hole.
Headlight Stanchion Pad
p/n: 70-0255-21
Mounting pads, horn and headlight stanchion base to hood latch shelf. Two and one half (2-1/2) inches by four and one fourth (4-1/4) inches.Length: 4.
Headlight tube flange gasket
p/n: 50-0223-14
Headlight tube flange gasket. Two (2) per car. Replaces #1234556.
Hinge Pillar Weatherstrip
p/n: 70-0734-63
Convertible Hinge Pillar Weatherstrip - Attaches to the body and seals between the A-pillar post and the front section of the door or vent window frame when the door is closed.
Hood Bumper
p/n: 60-0034-42
Bumper stop, hood, lower center. Two (2) required per vehicle.Length: 1.0 inches. Width: .75 inches. Height: .4375 inches.
Hood bumper
p/n: 70-0013-42
Pads, hood hold-down clamp, mount on clamp swivels to hold hood corners in. Set of four (4) rubber pads in solid brass, chrome plated cups.
Hood Bumper
p/n: 40-0354-42
Bumper, fender to hood. Two (2) per car. Held by four (4) rivets.Length: 2.9375 inches.
Hood Corner Pad
p/n: 40-0128-42
Pads, hood corners. Square type, brass core. Integral installation tabs. 90 degree angle, used on front or rear corners, as required.
Hood Corner Pad
p/n: 34-1186-42
Pads, hood door corners, cup type.1931 Twenty (20) required. 1932 Twenty Four (24) required.Height: .375 inches.
Hood Hinge Top Strap Pivot
p/n: 70-0045-42
A Hood Hinge Top Strap Pivot manufactured to OEM specifications to install for an authentic fit and finish. Cold rolled steel as original.
Hood latch swivel
p/n: 70-0061-42
Swivel, hood latch. Exact copy from .075 steel, pierced for rivets, not plated.
Hood Latch Swivel Pad
p/n: 34-0408-42
Pad, hood latch swivel for hood latch pressure against hood corners. For screw or rivet.
Hood Ventilator Bumper Set
p/n: 70-0011-42
This forty (40) piece Hood Ventilator Bumper set is designed from the original parts for superior fitment and function. The set includes bumpers and rivets for one (1) hood.
Horn trumpet grommet
p/n: 40-0086-21
Grommet for trumpet horn wire through motor cover. Close reproduction. Two (2) per car.
Inner Side Window Bumper
p/n: 70-0775-62
Bumper, inner side window garnish molding. One (1) per door.Length: 1.0 inches. Width: .3125 inches. Height: .25 inches.
LaSalle Monogram
p/n: 70-0056-49
LaSalle monograms for center of running board matting, exact copy, to be in-laid.
LaSalle monogram pedal pad
p/n: 70-0037-22
LaSalle pedal pads, clutch and brake, excellent copy from authentic original with LaSalle monogram.
Luggage Rack Grommet
p/n: 17-0021-46
Grommet, luggage rack support arm through body.Length: 2.25 inches. Width: 1.25 inches.
Muffler Bypass Floor Plate
p/n: 11-0006-88
Floor plate, muffler bypass control. Brass core as original, fully detailed.
Parking Light Mounting Pad
p/n: 30-0282-17
Gaskets, parking light (fender light).Length: 2.75 inches. Width: 1.75 inches.
Pressure Ring
p/n: 70-0261-69
Pressure ring (washer), sponge rubber, interior door handle and window regulator escutcheon. One and three fourths (1-3/4) inches outside diameter by three eighths (3/8) inch thick.
Quarter Window Weatherstrip
p/n: 60-0446-77
Weatherstrip, stationary quarter windows. Eight (8) foot strip for two (2) quarter windows. Most models with stationary windows.Length: 96.0 inches.
Radiator Brace Filler Strip
p/n: 70-0020-31
Filler strip, radiator brace rods. Retains ignition wire and thermometer tube in hollow brace rods. Thirty (30) inch strips.
Rear Axle Bumpers - Revulcanization
p/n: 11-0030-35
This Rear Axle Bumpers - Revulcanization is designed to restore your original rubber bumper pads to a like new condition. Service requires your metal cores. Please call or email for more service details and ordering. Revulcanization service only.
Rear Engine Support Pad
p/n: 70-0442-11
This Rear Engine Support Pad is used as a cushion at transmission. Makes a four (4) piece set after splitting. V-8 and V-12
Rear Engine Support Pad
p/n: 70-0443-11
This Rear Engine Support Pad is used as a cushion at transmission. Makes a four (4) piece set after splitting.
Rear Spring Bumper
p/n: 60-0137-32
Bumper, rear spring. Fits original retainer.Width: 2.5625 inches.
Rear spring bushing
p/n: 60-0311-35
Bushing, rear spring front eye, inlox cartridge type as original.
Rear Spring Pad
p/n: 70-0191-32
Pad, rear spring insulator for two (2) inch wide springs. (see our number 70-0245-32 for two and one fourth (2-1/4) inch springs). Cloth reinforced. Four (4) per vehicle.
Rear Spring Thrust Washer
p/n: 40-0526-32
Thrust washer, rear spring. "Silent Block". Three sixteenths (3/16) inch thick. Seven eighths (7/8) inch by one and five eighths (1-5/8).
Rear Spring Thrust Washer
p/n: 40-0525-32
Thrust washer, rear spring. "Silent Block". Three sixteenths (3/16) inch thick. One (1) inch by one and three fourths (1-3/4) inch.
Rear Window Gasket
p/n: 70-0084-77
This Rear Window Gasket comes in a seven foot, six inch (7' 6") strip and mounts around the full perimeter of the back glass. The ends may require trimming and bonding for installation.
Rear Window Gasket
p/n: 70-0018-83
This Rear Window Gasket comes in a seven foot, three inch (7' 3") strip and mounts around the full perimeter of the back glass. The ends may require trimming and bonding for installation.
Red Brake and Clutch Pedal Pad
p/n: 30-0188-89
Pads, brake and clutch pedal, slip over type. Black and red rubber. For black only see our #30-0188-22.Length: 3.875 inches. Width: 2.875 inches.
Rigid Run Channel
p/n: 70-0130-58
Special channel, felt lined rubber, for door upper front post for convertibles with cast upper post. Each piece sixteen (16) inches long.
Rumble Seat Lid Bumper Pad
p/n: 40-0297-85
Bumper, rumble seat lid. Sometimes used on trunk. One half (1/2) inch by one (1) inch by one (1) inch. Two (2) per car.Length: 1.0 inches. Width: 1.0 inches.
Rumble Seat Lid Bumper Pad
p/n: 60-0191-87
Bumper pad, rumble seat lid, upper corners. Compare with our #70-0120-87.Width: 1.0 inches. Height: 1.125 inches.