Access Hole Plug
p/n: 10-0010-44
Cover, rear apron over fuel tank. 3-1/2 inch diameter hollow cup to cover hole above fuel gauge sending unit.
Rear Window Gasket
p/n: 70-0018-83
This Rear Window Gasket comes in a seven foot, three inch (7' 3") strip and mounts around the full perimeter of the back glass. The ends may require trimming and bonding for installation.
Fuel Neck Grommet
p/n: 30-0099-41
Grommet, fuel filler neck. Three and one half (3-7/16) inch inside diameter for four (4) inch hole in apron.
Fuel Neck Grommet
p/n: 30-0232-41
Grommet, fuel filler neck. 2-1/2" inside diameter. Fits 3-3/8" hole in sheet metal. Overall width 4-1/8".
Hood Corner Pad
p/n: 40-0128-42
Pads, hood corners. Square type, brass core. Integral installation tabs. 90 degree angle, used on front or rear corners, as required.
Rear Window Gasket
p/n: 70-0084-77
This Rear Window Gasket comes in a seven foot, six inch (7' 6") strip and mounts around the full perimeter of the back glass. The ends may require trimming and bonding for installation.
Rumble Seat Step Pad
p/n: 40-0050-44
Pad, rumble seat step, with "P" logo, fully detailed slipover pad for old core. Fits original trim ring.Height: .50 inches.
Brake Master Cylinder Filler Access Hole Cover
p/n: 60-0016-24
This Master Cylinder Access Hole Cover is designed from the original part for superior fitment and seal. Secures the Brake Master Cylinder Filler and Inspection Access Hole in the vehicle.
Accelerator Pedal Pad
p/n: 10-0001-40
Pad, accelerator pedal. Cements and fastens with screws to original metal pedal. Length: 6.50 inches.
Transmission Mounting Pad
p/n: 11-0025-25
Mount, transmission. Original pattern, superior workmanship.
Headlight grommet
p/n: 25-0039-14
Base, headlight wire conduit and support post. (Vertical post under headlight).
Parking Light Mounting Pad
p/n: 30-0282-17
Gaskets, parking light (fender light).Length: 2.75 inches. Width: 1.75 inches.
Coil wire sleeve
p/n: 70-0109-21
Sleeve, coil wire to distributor. Fluted to match upper water hoses rubber only. V-12 & V-16 with coils mounted in radiator, V-8 with coils mounted horizontally on brace rods.
Gearshift Boot
p/n: 40-0076-88
Dust boot, gearshift, beehive type. Excellent copy and material. Used on some shift ball sockets.Length: 4.75 inches.
Headlight Stanchion Pad
p/n: 70-0255-21
Mounting pads, horn and headlight stanchion base to hood latch shelf. Two and one half (2-1/2) inches by four and one fourth (4-1/4) inches.Length: 4.
Taillight Gasket
p/n: 70-0258-15
Gaskets, taillight mounting under fender wire conduit base. Width: 3.25 inches.
Rumble Seat Step Pad
p/n: 60-0126-45
Pad, rumble seat step, on rear bumper bracket or fender. Rubber cover only, full slip-over type with bowtie emblem.
Engine Mount Pad
p/n: 11-0026-11
This Engine Mount Pad is designed to original pattern with superior workmanship. Made from high-quality EPDM rubber for a precise, factory like fit. Two (2) required per car.
Headlight tube flange gasket
p/n: 50-0223-14
Headlight tube flange gasket. Two (2) per car. Replaces #1234556.
Running Board or Inner Fender Splash Filler
p/n: 60-0288-45
This eight (8) foot Splash Filler strip is used for the running board apron to body or fender splash panels anti-rattle filler. This filler strip is top-quality EPDM sponge rubber to accept rivets or retaining screws.
Golf Bag Door Weatherstrip
p/n: 70-0118-85
This Golf Bag Door Weatherstrip is designed from the original part for superior fitment and seal. This seal mounts directly to the golf bag door.
Fuel Line Grommet
p/n: 30-0045-41
Grommet, fuel gauge and gas line through rear frame cross member. For five eighths (5/8) inch by two and three eighths (2-3/8) inch slot.Length: 2.
Body Mounting Pad
p/n: 70-0299-48
Pad, body mounting, for body bracket. Two (2) collars and retaining rings. Four (4) per car.
Fender Welting 1/4" Bead - 25ft
p/n: 70-1097-44
Welting, fender. Superior quality, proper construction of reinforced vinyl over vinyl core, one and three eighths (1-3/8) inch wide, black only. One fourth (1/4) inch bead, twenty-five (25) foot roll. Typically used to attach two (2) fenders to body.
Chrome Fender Welting - 25ft
p/n: 70-1101-44
Welting, fender, bright chrome vinyl, three sixteenths (3/16) inch bead, one and one half (1-1/2) inch width. Superior quality. Twenty five (25) foot roll. Typically used to attach two (2) fenders to body. For fifty (50) foot roll see our #70-1102-44.
Clutch and Brake Pedal Pads - Bowtie Emblem
p/n: 60-0043-22
This reproduction Clutch and Brake Pedal Pad pair slips over the full perimeter of the pedal for a precise, factory fit. A perfect reproduction to replace worn original pedal pads. Manufactured in quality black rubber. Excellent detail with bowtie emblem like original.
Fender Welting with 3/16 Bead - 25ft
p/n: 70-1099-44
A superior quality Fender Welting material constructed of reinforced black vinyl over a vinyl core. Typically used for attaching two (2) fenders to body. Sold in a 25 foot roll.
Rumble Seat Lid Bumper Pad
p/n: 60-0191-87
Bumper pad, rumble seat lid, upper corners. Compare with our #70-0120-87.Width: 1.0 inches. Height: 1.125 inches.
Cowl Vent Gasket
p/n: 30-0259-54
Gasket, cowl vent. Sponge rubber, good copy of original. Thirty seven and one half (37-1/2) inch developed length.Length: 37.50 inches.
Electrical terminal boot
p/n: 30-0061-21
Cover, starter cable terminal post inside to frame. Full detail and molded as original part.
Brake and clutch shank seal
p/n: 60-0019-24
Seal, brake and clutch pedal shank to floorboard. Single bellows rubber cup, seals air drafts around pedals.
Firewall Wiring Grommet
p/n: 25-0016-20
This Firewall Wiring Organizer Grommet is designed for original configuration and superior fit. Made from high-quality dense rubber to provide excellent durability.
Brake and clutch pedal bumper
p/n: 30-0380-20
Bumper, inclined toe board pedal hole, carried on toe board to meet our #30-0055-24 pedal. dust cover.
Side Window Sash Channel
p/n: 70-0641-58
This Side Window Sash Channel is the u-shaped steel channel only, no filler. Sold in 4 foot strip, usually sufficient for two (2) windows.
1-1/4" Firewall Grommet
p/n: 30-0060-21
This Firewall Grommet is used to run the coil wire and temperature gauge line through the firewall. Designed from the original part for superior fit and seal.
Brake and Clutch Shank Seal
p/n: 40-0175-24
Seal, brake and clutch pedal shank to floorboard. One and one half (1-1/2) inch by two and one eighth (2-1/8) inch by three fourths (3/4) inch thick.
Brake and Clutch Shank Seal
p/n: 30-0055-24
Seals, brake and clutch pedal shanks, against underside of floorboard.Length: 2.5625 inches. Width: 1.75 inches.
Headlight Bracket Pad
p/n: 50-0222-14
Headlight bracket-to-fender pad. POA #1245890-1, right and left.
Flexible Run Channel - 30 Inch Pair
p/n: 40-0309-57
Channel, side window glass, vertical run. Flexible, felt lined, rubber covered channel. Available in 30" pair.
Body Mounting Pad
p/n: 70-0297-48
Pad, body mounting. Three eighths (3/8) inch by two (2) inch by three (3) inch with collar and retainer ring.
Rumble Seat Lid Corner Pad
p/n: 70-0120-87
Pad, rumble seat lid corner, Compare with our #60-0191-87. Length: .75 inches.
5" Wide Bow Drill Cloth Tape
p/n: 70-1175-65
This Bow Drill Cloth Tape is used for covering convertible side window weatherstrip. Black in color and available in a five (5) foot roll.
Door Bumper
p/n: 10-0011-70
Cushion, door wedge plate, right and left, for door aligning lug receiver.Width: 1.1875 inches. Height: .625 inches.
Brake and Clutch Shank Seal
p/n: 40-0016-24
Seal, brake and clutch pedal shank to floorboard (draft excluder).Length: 2.4375 inches. Width: 1.875 inches.
Firewall Grommet
p/n: 50-0272-20
This Firewall Grommet is used to run the water temperature indicator pipe through the dash. Designed from the original part for superior fit and seal.
Starter Button Cover
p/n: 60-0322-21
This Starter Button Cover is designed from the original part for an authentic fit, finish, and appearance. A push on replacement to rod. Two (2") inch outside diameter.
Hood latch swivel
p/n: 70-0061-42
Swivel, hood latch. Exact copy from .075 steel, pierced for rivets, not plated.
Accelerator Rod Button Cover
p/n: 60-0357-40
Cover, accelerator rod button. Round slip-over type. Good copy with bow tie center. Height: .4375 inches.
Detachable Centerpost Pads
p/n: 30-0108-67
This Detachable Centerpost Pad pair is designed from the original part for an authentic fit and finish.
Shock Absorber Arm Bushing
p/n: 30-0192-32
Bushing, shock absorber arm. Restore proper shock action.Height: 1.375 inches.
Steering Column Spacer
p/n: 60-0563-32
Spacer, steering column to dash at U-clamp.Length: 2.50 inches.
Rear Spring Pad
p/n: 70-0191-32
Pad, rear spring insulator for two (2) inch wide springs. (see our number 70-0245-32 for two and one fourth (2-1/4) inch springs). Cloth reinforced. Four (4) per vehicle.
Shock Absorber Arm Bushing
p/n: 15-0005-33
Bushing, shock absorber arm ball joint.Height: .875 inches.
Door Alignment Pad
p/n: 70-1821-71
Wedge pads, door aligning.Length: 1.125 inches. Width: .5 inches. Height: .875 inches.
Starter Pedal Button Cover
p/n: 60-0166-21
This Starter Button Pedal Cover is designed from the original part for an authentic fit, finish, and appearance. Rubber slip over type for old metal. Two (2") inch outside diameter.
Firewall Grommet
p/n: 30-0093-21
This Firewall Grommet is used to run the ignition advance along with various rods and tubing through the firewall. Designed from the original part for superior fit and seal.
Shock Absorber Bushing
p/n: 40-0069-32
Bushing, shock absorber link, flanged at both ends. Seven eighths (7/8) inch long between flanges, one (1) inch diameter barrel.
Battery Clamp Cover
p/n: 70-0095-21
This Battery Clamp Cover helps to protect the nearby metal and finish. Fully molded from high-quality EPDM rubber to ensure durability. Good copy from an original part.
Channel Filler Weatherstrip
p/n: 20-2091-62
This Channel Filler Weatherstrip is designed from the original part for superior fitment and seal. This door glass to body filler seal fits in the metal channel that holds the glass piece. Sold in a 36" strips.
Brake shaft stop bumper
p/n: 70-0271-24
Bumper, brake rocker shaft lever stop. Two (2) used per car. Also used as door side bumper for some 1927-31 Cadillacs.
Door Bumper
p/n: 30-0002-71
Bumper, door side. One and one fourth (1-1/4) inch by two (2) inch.Length: 2.0 inches. Width: 1.25 inches.
Engine Mount Pad
p/n: 11-0028-11
This Engine Mount Pad is designed to original pattern with superior workmanship. Made of a high-quality EPDM dense rubber for durability and authentic fit.
Door Bumper
p/n: 34-0342-71
Door bumper, round, rubber with steel insert, (called door anti-rattle). Two (2) per door on all closed body styles, one (1) per door on convertible Sedan.
Coil wire sleeve
p/n: 40-0336-21
Nipple, sparkplug wire at sparkplug, for right angle plug terminal. This is an exact copy of the style used at the time. Not a modernistic makeover.
Shock Absorber Bushing
p/n: 40-0273-32
Bushing. shock absorber link, smaller type. Eight (8) required per car. Compare with our #40-0069-32 (larger type). Length: .9375 inches.
Starter Button Cover
p/n: 60-0358-21
Cover, starter rod button, round slip over type. One and seven sixteenths (1-7/16) inch outside diameter. Good copy with bow tie center.
Door Handle Ferrule
p/n: 70-0111-69
A Ferrule for three fourths (3/4") inch outside door handles. Chrome plated brass. Used for outside door handle or outside trunk handle.
2-1/2" Black Bow Drill Cloth Tape
p/n: 70-1172-65
This Bow Drill Cloth Tape is used for covering convertible side window weatherstrip. Black in color and available in a five (5) foot roll.
Door Bumper
p/n: 70-1154-71
Pad, door jamb, rear door fender cut out. One and one half (1-1/2) inch outside diameter, seven eighths (7/8) inch plug.
Engine Mount Pad
p/n: 11-0029-11
This Engine Mount Pad is designed to original pattern with superior workmanship. Made of a high-quality EPDM dense rubber for durability and authentic fit.
2-1/2" Tan Bow Drill Cloth Tape
p/n: 70-1173-65
This Bow Drill Cloth Tape is used for covering convertible side window weatherstrip. Tan in color and available in a five (5) foot roll.
Door Check Link Rod End Stop
p/n: 70-0326-70
End stop and pad, door check link rod. Rubber with embedded steel plate, five sixteenths (5/16) inch diameter thread. Most models with rod type door checks.
Shock or Stabilizer Link Cross Pin Bushing
p/n: 50-0220-32
This Shock or Stabilizer Link Cross Pin Bushing is designed from the original part for superior fitment and function. A rubber bushing for shock absorber link cross pin or stabilizer cross link pin.
Engine Mount Pad
p/n: 11-0027-11
This Engine Mount Pad is designed to original pattern with superior workmanship. Made of a high-quality EPDM dense rubber for durability and authentic fit.
Door Bumper
p/n: 70-1157-71
Pad, door jamb (door side bumper).Some bodies using escutcheons around pads.Length: 1.5625 inches. Width: 1.1875 inches.
Door Bumper
p/n: 30-0350-71
Bumper, door dovetail. Goes in door opening, two (2) door, under steel cap in dovetail receiver.Width: 1.125 inches. Height: .9375 inches.
Dimmer Switch Grommet
p/n: 40-0083-88
This Dimmer Switch Grommet is used during carpet installations in automotive restorations. Made from high-quality EPDM dense rubber to provide excellent durability. Includes a wide flange for floor dimmer switch fitments.
Door and Trunk Handle Gasket
p/n: 40-0132-70
Pad, door handle escutcheon. Two and five sixteenths (2-5/16) inch by one and seven sixteenths (1-7/16) inch.
Door Jamb Bumper Pad
p/n: 40-0042-70
This Door Jamb Bumper Pad is designed from the original part for superior fitment and seal. A reproduction of earlier type, screw retained and a perfect copy.
Door Bumper
p/n: 70-1156-71
Door Side Bumper made from EPDM Dense rubber. Clip retained. Appears identical to Atwood #107, #208. Width: 1-1/2" inches. Height: 1-5/16"
Door Bumper
p/n: 70-1155-71
Pad, door jamb (door side bumper).Length: 1.25 inches. Width: .9375 inches.